W DOC AIRBUS | AMM A320F

Detailed Inspection of Outer-Wing Flap-Track-Beams 2, 3, 4 Aft-Spigot

TASK 57-26-00-220-005-A
Detailed Inspection of Outer-Wing Flap-Track-Beams 2, 3, 4 Aft-Spigot

WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.
WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:
  • THE FLIGHT CONTROLS
  • THE FLIGHT CONTROL SURFACES
  • THE LANDING GEAR AND THE RELATED DOORS
  • COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.
CAUTION: BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
  • DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
  • DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
  • MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
ZONE: 530
ZONE: 630
1. Reason for the Job
Refer to the MPD TASK: 572610-01
NOTE: The effectivity of this task is ALL. To know if this task is applicable for your aircraft, refer to the MPD task applicability and the weight variant data given in the SRM introduction.
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
AR
ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
No specific
AR
SAFETY BARRIER(S)
No specific
AR
SAFETY CLIP - CIRCUIT BREAKER
No specific
AR
WARNING NOTICE(S)
No specific
Torque wrench: range to between 1.21 and 0.99 m.daN (107.08 and 87.61 lbf.in ) T
98D27803000000
1
LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION
 B. Consumable Materials
REFERENCE
DESIGNATION
(Material No.08BAA9)
Non Aqueous Cleaner-General - -
(Material No.14SBA1)
Textile-Lint free Cotton -
 C. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
530
L WG FLAP TAB, FLAP TRACK FAIR & WG TIP
630
RIGHT WING FLAP TRACK FAIR AND WING TIP
531CB, 532CB, 533CB, 631CB, 632CB, 633CB
 D. Referenced Information
REFERENCE
DESIGNATION
TASK 27-50-00-866-008-A
Extension of the Flaps on the Ground
TASK 27-50-00-866-008-A-01
Extension of the Flaps/Slats on the Ground
TASK 27-50-00-866-009-A
Retraction of the Flaps on the Ground
TASK 27-50-00-866-009-A-01
Retraction of the Flaps/Slats on the Ground
TASK 57-55-11-000-001-A
Removal of the Flap Track Fairings Nos. 2, 3 and 4
TASK 57-55-11-000-004-A
Removal of the Flap Track Fairings Nos. 2, 3 and 4
TASK 57-55-11-400-001-A
Installation of the Flap Track Fairings Nos. 2, 3 and 4
TASK 57-55-11-400-004-A
Installation of the Flap Track Fairings Nos. 2, 3 and 4
SRM 572600
 (for corrective action)
CMM 575141
 (for corrective action)
F Flap Track Beams 2, 3 and 4 - Aft Spigots
3. Job Set-up
Subtask 57-26-00-941-066-A
A. Safety Precautions
   (1) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's instructions and your local regulations.
   (2) Put WARNING NOTICE(S) in the cockpit to tell persons not to operate the flaps or slats.
Subtask 57-26-00-866-062-A
B. Aircraft Maintenance Configuration
   (1) Fully extend the flaps (Ref. AMM TASK 27-50-00-866-008).
   (2) Make sure that the 98D27803000000 LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION is on the control lever.
Subtask 57-26-00-865-062-A
C. Open, safety and tag this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C ALL
49VUFLIGHT CONTROLS/FLP/CTL AND MONG/SYS16CVB07
121VUFLIGHT CONTROLS/FLP/CTL AND/MONG/SYS28CVQ21
Subtask 57-26-00-010-067-A ** ON A/C NOT FOR ALL
D. Get Access
   (1) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE below the applicable wing trailing edge at the flap tracks 2, 3 and 4, zones 531(631), 532(632) and 533(633).
   (2) Remove the applicable flap track fairing access panels (Ref. AMM TASK 57-55-11-000-001):
     (a) For the flap track 2,:
  • for the left wing, remove 531CB
  • for the right wing, remove 631CB.
     (b) For the flap track 3,:
  • for the left wing, remove 532CB
  • for the right wing, remove 632CB.
     (c) For the flap track 4,:
  • for the left wing, remove 533CB
  • for the right wing, remove 633CB.
Subtask 57-26-00-010-067-B ** ON A/C NOT FOR ALL
D. Get Access
   (1) Put the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE below the applicable wing trailing edge at the flap tracks 2, 3 and 4, zones 531(631), 532(632) and 533(633).
   (2) Remove the applicable flap track fairing access panels (Ref. AMM TASK 57-55-11-000-004):
     (a) For the flap track 2,:
  • for the left wing, remove 531CB
  • for the right wing, remove 631CB.
     (b) For the flap track 3,:
  • for the left wing, remove 532CB
  • for the right wing, remove 632CB.
     (c) For the flap track 4,:
  • for the left wing, remove 533CB
  • for the right wing, remove 633CB.
4. Procedure
CAUTION: BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
  • DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
  • DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
  • MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
Subtask 57-26-00-110-060-A
A. Preparation for Inspection
   (1) Use a Textile-Lint free Cotton - (Material No.14SBA1) , made moist with Non Aqueous Cleaner-General - - (Material No.08BAA9) to clean the aft spigot of the applicable flap track beam.
Subtask 57-26-00-280-054-A
B. Detailed Inspection of Outer-Wing Flap-Track-Beams 2, 3, 4 Aft-Spigot
   (1) TORQUE the nut of the aft spigot to between 1.21 and 0.99 m.daN (107.08 and 87.61 lbf.in ) T.
   (2) Make sure that the nut of the aft spigot does not turn.
NOTE: If necessary, refer to the SRM 572600 or the flap track beam CMM 575141 for the correct repair procedure.
5. Close-up
Subtask 57-26-00-410-069-A ** ON A/C NOT FOR ALL
A. Close Access
   (1) Make sure that the work area is clean and clear of tools and other items.
   (2) Install the applicable flap track fairing access panels (Ref. AMM TASK 57-55-11-400-001):
     (a) For the flap track 2,:
  • for the left wing, install 531CB
  • for the right wing, install 631CB.
     (b) For the flap track 3,:
  • for the left wing, install 532CB
  • for the right wing, install 632CB.
     (c) For the flap track 4,:
  • for the left wing, install 533CB
  • for the right wing, install 633CB.
Subtask 57-26-00-410-069-B ** ON A/C NOT FOR ALL
A. Close Access
   (1) Make sure that the work area is clean and clear of tools and other items.
   (2) Install the applicable flap track fairing access panels (Ref. AMM TASK 57-55-11-400-004):
     (a) For the flap track 2,:
  • for the left wing, install 531CB
  • for the right wing, install 631CB.
     (b) For the flap track 3,:
  • for the left wing, install 532CB
  • for the right wing, install 632CB.
     (c) For the flap track 4,:
  • for the left wing, install 533CB
  • for the right wing, install 633CB.
Subtask 57-26-00-865-063-A
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C ALL
49VUFLIGHT CONTROLS/FLP/CTL AND MONG/SYS16CVB07
121VUFLIGHT CONTROLS/FLP/CTL AND/MONG/SYS28CVQ21
Subtask 57-26-00-866-063-A
C. Aircraft Maintenance Configuration
   (1) Make sure that the work area is clean and clear of tools and other items.
   (2) Remove the 98D27803000000 LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION from the flap/slat control lever.
   (3) Retract the flaps (Ref. AMM TASK 27-50-00-866-009).
   (4) On the servocontrol, make sure that the pointer on the hex. head is opposite the letter 'O' on the housing.
Subtask 57-26-00-942-061-A
D. Removal of Equipment
   (1) Remove the safety barriers.
   (2) Remove the WARNING NOTICE(S).
   (3) Remove the access platform(s).
   (4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
[Rev.8 from Aug 2017] 2026.04.01 02:11:31 UTC
"Aviabrain" 2025