Special Detailed Inspection (US) of Front Spar Joint at RIB 24, Aft Face

TASK 57-21-00-280-806-A
Special Detailed Inspection (US) of Front Spar Joint at RIB 24, Aft Face

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

ZONE: 550
ZONE: 650

1. Reason for the Job
Refer to the MPD TASK: 572172-02

NOTE: The effectivity of this task is "ALL". To know if this task is applicable for your aircraft, refer to the MPD task applicability and the weight variant data given in the SRM introduction.

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 4M (13 FT)
No specific	AR	SAFETY BARRIER(S)
No specific	AR	WARNING NOTICE(S)
98D27803500001	1	LOCKING TOOL ZERO POS

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.14SBA1)	Textile-Lint free Cotton -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
550	VENT SURGE TANK
650	VENT SURGE TANK
550CB, 650CB

D. Referenced Information

REFERENCE	DESIGNATION
TASK 12-11-28-650-003-A	Pressure Refuel with Automatic Control
TASK 28-10-00-910-001-A	Safety Procedures When You Do Work in a Fuel Tank
TASK 28-12-45-000-001-A	Removal of the Panel Assembly
TASK 28-12-45-400-002-A	Installation of the Panel Assembly
TASK 28-25-00-650-001-A	Pressure Defuel
TASK 28-25-00-650-003-A	To Drain Remaining Fuel from the Wing Tanks and the Center Tank
TASK 28-25-00-650-003-A-01	To Drain Remaining Fuel from the Wing Tanks and the Center Tank
TASK 28-25-00-869-001-A	Fuel Transfer
SRM 572100
NTM 572172
Details of the Front Spar Joint at RIB 24, Aft Face

3. Job Set-up
Subtask 57-21-00-941-108-A

A. Safety Precautions

WARNING: OBEY THE SAFETY PROCEDURES WHEN YOU DO WORK IN A FUEL TANK.

(1) You must obey the fuel safety procedures when you do work in a fuel tank (Ref. AMM TASK 28-10-00-910-001).
(2) Install the 98D27803500001 LOCKING TOOL ZERO POS on the flap/slat control lever.
(3) Put a WARNING NOTICE(S) in the cockpit to tell persons not to operate the flaps or slats.
(4) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's instructions and your local regulations.

Subtask 57-21-00-650-102-A

B. Fuel Configuration
(1) Defuel the applicable fuel tank (Ref. AMM TASK 28-25-00-650-001).
(2) Drain the remaining fuel from the applicable fuel tank (Ref. AMM TASK 28-25-00-650-003).

Subtask 57-21-00-010-100-A

C. Get Access
(1) Put an ACCESS PLATFORM 4M (13 FT) in position:
(a) For the left wing, below zone 550.
(b) For the right wing, below zone 650.
(2) Remove the applicable access panel (Ref. AMM TASK 28-12-45-000-001):
(a) For the left wing, remove 550CB.
(b) For the right wing, remove 650CB.

4. Procedure
Subtask 57-21-00-110-096-A

A. Preparation for Inspection
(1) Use a clean Textile-Lint free Cotton - (Material No.14SBA1) , made moist with Non Aqueous Cleaner-General - - (Material No.08BAA9) to clean the applicable inspection area.

Subtask 57-21-00-280-058-A

B. Special Detailed Inspection (US) of Front Spar Joint at RIB 24, Aft Face
(1) Examine the applicable inspection area NTM 572172.

NOTE: If necessary, refer to the SRM 572100 for the correct repair procedure.

5. Close-up
Subtask 57-21-00-410-092-A

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the applicable access panel (Ref. AMM TASK 28-12-45-400-002):
(a) For the left wing, install 550CB.
(b) For the right wing, install 650CB.

Subtask 57-21-00-650-103-A

B. Fuel Configuration
(1) Refuel (Ref. AMM TASK 12-11-28-650-003) or transfer fuel (Ref. AMM TASK 28-25-00-869-001) as necessary.

Subtask 57-21-00-942-103-A

C. Removal of Equipment
(1) Remove the safety barriers.
(2) Remove the access platform(s).
(3) Remove the 98D27803500001 LOCKING TOOL ZERO POS from the flap/slat control lever.
(4) Remove the WARNING NOTICE(S).
(5) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

[Rev.8 from Aug 2017] 2026.04.01 02:11:08 UTC