W DOC AIRBUS | AMM A320F

Installation of the Bearing of the Pylon Rear Attachment at RIB10

TASK 54-51-17-400-003-A
Installation of the Bearing of the Pylon Rear Attachment at RIB10

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:
  • THE FLIGHT CONTROLS
  • THE FLIGHT CONTROL SURFACES
  • THE LANDING GEAR AND THE RELATED DOORS
  • COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.
WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
CAUTION: BEFORE YOU INSTALL/REMOVE THE GSE-TOOL, READ THE INSTRUCTIONS IN THE APPLICABLE GSE INSTRUCTION MANUAL. WHILE YOU OPERATE THIS TOOL, CAREFULLY OBEY THEM. IF YOU DO NOT OBEY THE INSTRUCTIONS, DAMAGE TO EQUIPMENT CAN OCCUR.
CAUTION: THIS PART IS A REMOVABLE STRUCTURAL COMPONENT (RSC), WHICH CAN BE MOVED BETWEEN AIRCRAFT. THUS IT CAN HAVE DIFFERENT OPERATION CONDITIONS AND A DIFFERENT LIFE RECORD (FLIGHT HOURS/FLIGHT CYCLES/CALENDAR) FROM THE AIRCRAFT IT IS INSTALLED ON OR REMOVED FROM. THE OPERATOR IS RESPONSIBLE FOR THE SPECIFIC TRACKING AND CONTINUED AIRWORTHINESS OF REMOVABLE STRUCTURAL COMPONENTS. INCORRECT MAINTENANCE OF THESE COMPONENTS CAN CAUSE A RISK FOR THE FLIGHT SAFETY.
ZONE: 400
1. Reason for the Job
Self explanatory
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
AR
ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
No specific
AR
SPATULA - PLASTIC
No specific
AR
WARNING NOTICE(S)
No specific
Torque wrench: range to between 40 and 30 m.daN (294.99 and 221.24 lbf.ft ) T
98D54003006000
1
WRENCH-CASTELLETED
 B. Consumable Materials
REFERENCE
DESIGNATION
(Material No.03HBD9)
Synthetic Ester base Grease-General Purpose Low Temp -
(Material No.08BAA9)
Non Aqueous Cleaner-General - -
(Material No.14SBA1)
Textile-Lint free Cotton -
 C. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
400
POWER PLANT, NACELLES AND PYLONS
 D. Expendable Parts
FIG.ITEM
DESIGNATION
IPC-CSN
4
BEARINGS
AIPC 54-51-29-04-010
 E. Referenced Information
REFERENCE
DESIGNATION
TASK 28-00-00-910-001-A
Fuel Safety Procedures
TASK 54-51-17-400-002-A
Installation of the Pylon-to-Wing Aft Attach-Fitting at RIB10
TASK 78-30-00-040-012-A
Deactivation of the Thrust Reverser Hydraulic Control Unit (HCU) for Ground Maintenance
TASK 78-30-00-081-041-A
Make the Thrust Reverser Serviceable after Maintenance
TASK 78-30-00-081-041-B
Make the Thrust Reverser Serviceable after Maintenance
TASK 78-30-00-440-012-A
Re-activation of the Thrust Reverser Hydraulic Control Unit (HCU) after Ground Maintenance
TASK 78-30-00-481-041-A
Make the Thrust Reverser Unserviceable for Maintenance
TASK 78-30-00-481-041-B
Make the Thrust Reverser Unserviceable for Maintenance
F Pylon Rear Attachment at RIB10 ** ON A/C NOT FOR ALL
F Pylon Rear Attachment at RIB10 ** ON A/C NOT FOR ALL
3. Job Set-up
Subtask 54-51-17-941-058-A ** ON A/C NOT FOR ALL
A. Safety Precautions
   (1) Make sure that the WARNING NOTICE(S) is(are) in position to tell persons not to start engine 1(2).
   (2) On the ENG section of overhead maintenance panel 50VU:
     (a) Make sure that the ON legend of the FADEC GND PWR 1(2) pushbutton switch is off.
     (b) Make sure that the WARNING NOTICE(S) is(are) in position to tell persons not to energize FADEC 1(2).
   (3) Make sure that you obeyed the instructions of the fuel safety procedure (Ref. AMM TASK 28-00-00-910-001).
WARNING: MAKE SURE THAT THE THRUST REVERSER IS LOCKED. IF NOT, THE THRUST REVERSER CAN OPERATE ACCIDENTALLY AND CAUSE INJURY TO PERSONNEL AND/OR DAMAGE TO THE REVERSER.
   (4) Make sure that the thrust reverser is unserviceable for maintenance (Ref. AMM TASK 78-30-00-481-041).
   (5) Make sure that the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE is in position:
     (a) For the left pylon, at zone 470
     (b) For the right pylon, at zone 480.
Subtask 54-51-17-941-058-B ** ON A/C NOT FOR ALL
A. Safety Precautions
   (1) Make sure that a WARNING NOTICE(S) is in position in the cockpit to tell persons not to start engine 1(2).
   (2) On overhead maintenance panel 50VU:
     (a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
     (b) Make sure that there is a WARNING NOTICE(S) in position to tell persons not to energize FADEC 1(2).
   (3) Make sure that the fuel safety procedure instructions are obeyed (Ref. AMM TASK 28-00-00-910-001).
WARNING: MAKE SURE THAT THE THRUST REVERSER IS LOCKED. IF NOT, THE THRUST REVERSER CAN OPERATE ACCIDENTALLY AND CAUSE INJURY TO PERSONNEL AND/OR DAMAGE TO THE REVERSER.
   (4) Make sure that the thrust reverser is unserviceable for maintenance (Ref. AMM TASK 78-30-00-040-012).
   (5) Make sure that the ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE is in position:
     (a) For the left pylon, in zone 470
     (b) For the right pylon, in zone 480.
4. Procedure
Subtask 54-51-17-110-050-A ** ON A/C NOT FOR ALL
A. Preparation before Installation
F Pylon Rear Attachment at RIB10 ** ON A/C NOT FOR ALL
F Pylon Rear Attachment at RIB10 ** ON A/C NOT FOR ALL
   (1) Clean the parts that you kept from the removed component with Non Aqueous Cleaner-General - - (Material No.08BAA9) and the Textile-Lint free Cotton - (Material No.14SBA1) .
   (2) Use the SPATULA - PLASTIC to remove the unwanted material from the interface of the pylon rear attachment.
   (3) Clean the interface of the bearings (4) and the pylon rear attachment (3) with Non Aqueous Cleaner-General - - (Material No.08BAA9) and the Textile-Lint free Cotton - (Material No.14SBA1) .
   (4) Examine the pylon rear attachment and the adjacent structure for:
  • Cracks
  • Damaged paint and sealant
  • Distortion
  • Correct condition of all fasteners and safety devices.
Subtask 54-51-17-420-060-A ** ON A/C NOT FOR ALL
B. Installation of the Bearing of the Pylon Rear Attachment
F Pylon Rear Attachment at RIB10 ** ON A/C NOT FOR ALL
F Pylon Rear Attachment at RIB10 ** ON A/C NOT FOR ALL
   (1) Apply Synthetic Ester base Grease-General Purpose Low Temp - (Material No.03HBD9) to the interface of the bearings (4) and the pylon rear attachment (3).
   (2) Install the new AIPC 54-51-29-04-010 BEARINGS (4) on the pylon rear attachment (3) with the 98D54003006000 WRENCH-CASTELLETED (98D54003006202).
   (3) Install the new tab washers (2).
   (4) Make sure that the internal tab of the washers (2) is engaged in the slot on the bearings (4).
   (5) Lightly bend the tabs of the tab washers (2) before you install the slotted nuts (1).
NOTE: This will make the locking of the slotted nuts easier.
   (6) Install the slotted nuts (1) on the bearings (4) with the chamfered face against the tab washers (2).
   (7) Hold the bearings (4) with the 98D54003006000 WRENCH-CASTELLETED (98D54003006202).
   (8) TORQUE the slotted nuts (1) to between 40 and 30 m.daN (294.99 and 221.24 lbf.ft ) T with the 98D54003006000 WRENCH-CASTELLETED (98D54003006200).
   (9) Safety the slotted nuts (1) with the tab washers (2).
5. Close-up
Subtask 54-51-17-410-054-A ** ON A/C NOT FOR ALL
A. Close Access
   (1) Install the applicable pylon-to-wing aft attach-fitting at RIB10 (Ref. AMM TASK 54-51-17-400-002).
Subtask 54-51-17-440-050-A ** ON A/C NOT FOR ALL
B. Aircraft Maintenance Configuration
   (1) Make the thrust reverser serviceable after maintenance (Ref. AMM TASK 78-30-00-081-041).
Subtask 54-51-17-440-050-B ** ON A/C NOT FOR ALL
B. Aircraft Maintenance Configuration
   (1) Make the thrust reverser serviceable after maintenance (Ref. AMM TASK 78-30-00-440-012).
Subtask 54-51-17-942-056-A ** ON A/C NOT FOR ALL
C. Put the aircraft back to its initial configuration.
   (1) Make sure that the work area is clean and clear of tools and other items.
   (2) Remove the access platform(s).
   (3) Remove the WARNING NOTICE(S).
[Rev.10 from 2021] 2026.04.01 02:00:34 UTC
"Aviabrain" 2025