Removal of Oil Lube Module (131-9(A))

TASK 49-91-45-000-003-A
Removal of Oil Lube Module (131-9(A))

WARNING: DO NOT TOUCH THE APU UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).

ZONE: 315
ZONE: 316

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE
No specific	AR	CAP - BLANKING
No specific	1	CONTAINER 10 L(2 1/2 USGAL)
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	AR	WARNING NOTICE(S)
98L12003001000	AR	HARNESS,SAFETY

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
315	TAIL CONE APU AND ACCESSORY COMPARTMENT
316	TAIL CONE APU AND ACCESSORY COMPARTMENT
315AL, 316AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 24-42-00-861-001-A	Energize the Ground Service Network from the External Power
TASK 29-00-00-864-001-A	Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action
TASK 49-32-11-000-003-A	Removal of the Fuel Control Unit (FCU) (131-9(A))
TASK 52-41-00-010-001-A	Open the APU Doors for Access
Oil Lube Module

3. Job Set-up
Subtask 49-91-45-860-055-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Energize the ground service network
(Ref. AMM TASK 24-42-00-861-001).
(2) On the overhead panel 25VU, make sure that the APU MASTER SW pushbutton switch is released (the ON legend is off).
(3) On the APU section of overhead panel 25VU, put a WARNING NOTICE(S) to tell persons not to start the APU.
(4) Make sure that the hydraulic systems are depressurized
(Ref. AMM TASK 29-00-00-864-001).

Subtask 49-91-45-865-059-A ** ON A/C NOT FOR ALL

B. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
121VU	APU/APU/CTL	2KD	L42
121VU	APU/ECB/SPLY	1KD	L41

Subtask 49-91-45-010-053-A ** ON A/C NOT FOR ALL

C. Get Access

WARNING: BEFORE YOU START WORK, YOU MUST PUT ON A SAFETY HARNESS AND ATTACH IT TO THE ACCESS PLATFORM. WITHOUT A SAFETY HARNESS, YOU CAN FALL. THIS CAN KILL YOU OR CAUSE YOU INJURY.

(1) Put on and attach the HARNESS, SAFETY before you start work in the work area.
(2) Put an ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE in position below the APU access doors 315AL and 316AR.
(3) Open APU access doors 315AL and 316AR (Ref. AMM TASK 52-41-00-010-001).
(4) Set the light switch 11LJ to the ON position.

4. Procedure
Subtask 49-91-45-020-055-A ** ON A/C NOT FOR ALL

A. Remove the Oil Lube Module
(1) Remove the fuel control unit (Ref. AMM TASK 49-32-11-000-003).
(2) Put the CONTAINER 10 L(2 1/2 USGAL) below the oil lube module (4).
(3) Disconnect the electrical connectors (3).
(4) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(5) Loosen the captive bolts (1) and remove the oil lube module (4) from the APU.
(6) Remove and discard the packing (2) from the mounting boss.

[Rev.10 from 2021] 2026.04.01 01:33:36 UTC