DOC AIRBUS | AMM A320FRemoval of the Accent Washtable Light
TASK 33-24-12-000-805-A
Removal of the Accent Washtable Light
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Referenced Information
3. Job Set-up
Subtask 33-24-12-860-060-A ** ON A/C NOT FOR ALL
Subtask 33-24-12-020-055-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 06:20:09 UTC
Removal of the Accent Washtable Light
FIN: 54LQ13 ** ON A/C NOT FOR ALL
FIN: 56LQ6 ** ON A/C NOT FOR ALL
FIN: 61LQ111 ** ON A/C NOT FOR ALL
FIN: 61LQ112 ** ON A/C NOT FOR ALL
1. Reason for the JobFIN: 56LQ6 ** ON A/C NOT FOR ALL
FIN: 61LQ111 ** ON A/C NOT FOR ALL
FIN: 61LQ112 ** ON A/C NOT FOR ALL
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | CAP - BLANKING |
| No specific | 1 | ELEC CONTACTS INSERTION EXTRACTION TOOL M15570-20 |
| No specific | 1 | PIN - NON METALLIC |
| No specific | AR | SAFETY CLIP - CIRCUIT BREAKER |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-41-00-861-002-A | Energize the Aircraft Electrical Circuits from the External Power |
| TASK 24-41-00-861-002-A-01 | Energize the Aircraft Electrical Circuits from the APU |
| TASK 24-41-00-861-002-A-02 | Energize the Aircraft Electrical Circuits from Engine 1(2) |
| FOR [56LQ6] (WASH TABLE LIGHT) | |
| TASK 25-45-38-000-802-A | Removal of the Wash Basin of the Space Flex Lavatory |
Wash Table LightSubtask 33-24-12-860-060-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).
Subtask 33-24-12-865-067-A ** ON A/C NOT FOR ALL (1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).
B. Open, safety and tag this(these) circuit breaker(s):
Subtask 33-24-12-010-054-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | LIGHTING/EMER LT/CABIN | 79WL | H07 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | LIGHTING/EMER LT/CABIN | 79WL | H05 |
| ** ON A/C NOT FOR ALL | |||
| 2000VU | LAV FWD-OCCUPIED | 1WJ | F01 |
| ** ON A/C NOT FOR ALL | |||
| 2000VU | LIGHT-LAV | 1LQ | J01 |
| ** ON A/C NOT FOR ALL | |||
| 2000VU | LAV FWD & MID-OCCUPIED | 1WJ | F01 |
| ** ON A/C NOT FOR ALL | |||
| 2001VU | LAVATORY AFT-OCCUPIED | 11WJ | B04 |
C. Get Access
(1) Get Access to the Wash Table Light in the Spaceflex lavatory:
(a) FOR [56LQ6] (WASH TABLE LIGHT)
Subtask 33-24-12-010-059-A ** ON A/C NOT FOR ALL (1) Get Access to the Wash Table Light in the Spaceflex lavatory:
(a) FOR [56LQ6] (WASH TABLE LIGHT)
- Remove the Wash Basin if necessary (Ref. AMM TASK 25-45-38-000-802).
D. Get Access
(1) Get Access to the Wash Table Light in the SMART lavatory:
(a) FOR 61LQ*
1 Open the baby nursing table.
2 On the service cabinet above the baby nursing table, in the upper left and right corner, push the service cabinet to disengage and lower it.
4. Procedure(1) Get Access to the Wash Table Light in the SMART lavatory:
(a) FOR 61LQ*
1 Open the baby nursing table.
2 On the service cabinet above the baby nursing table, in the upper left and right corner, push the service cabinet to disengage and lower it.
Subtask 33-24-12-020-055-A ** ON A/C NOT FOR ALL
A. Removal of the Wash Table Light in the Spaceflex Lavatory
(1) Remove the screws (7) and the passenger service unit (1).
(3) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(4) Cut and discard the TIE WRAPS (3) to release the cable (2).
(5) Pull the wash table light (5) to release it from the clamps (6).
(6) Remove the wash table light (5).
Subtask 33-24-12-020-060-A ** ON A/C NOT FOR ALL (1) Remove the screws (7) and the passenger service unit (1).
CAUTION:
MAKE MATCH MARKS ON ALL THE ELECTRICAL WIRES BEFORE YOU DISCONNECT THEM. INCORRECT CONNECTION OF WIRES WILL CAUSE DAMAGE TO EQUIPMENT.
CAUTION:
MAKE SURE THAT THE ELECTRICAL CONNECTORS ARE CLEAN BEFORE YOU DISCONNECT OR CONNECT THEM. CONTAMINATION ON THE ELECTRICAL CONNECTORS CAN CAUSE DAMAGE TO EQUIPMENT.
(2) Disconnect the electrical connector (4). (3) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(4) Cut and discard the TIE WRAPS (3) to release the cable (2).
(5) Pull the wash table light (5) to release it from the clamps (6).
(6) Remove the wash table light (5).
B. Removal of the Wash Table Light in the SMART Lavatory
(1) Remove the screws (9) and the washers (10) from the brackets (11) and remove the terminal block (2) from the lavatory wall.
(3) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(4) Cut and discard the TIE WRAPS (3) to release the cable (8).
(5) Push the quick-release fasteners (6) with the PIN - NON METALLIC to disengage them and remove the cover (5).
(6) Pull the wash table light (4) to release it from the clamps (7).
(7) Remove the wash table light (4).
(1) Remove the screws (9) and the washers (10) from the brackets (11) and remove the terminal block (2) from the lavatory wall.
CAUTION:
MAKE MATCH MARKS ON ALL THE ELECTRICAL WIRES BEFORE YOU DISCONNECT THEM. INCORRECT CONNECTION OF WIRES WILL CAUSE DAMAGE TO EQUIPMENT.
CAUTION:
MAKE SURE THAT THE ELECTRICAL CONNECTORS ARE CLEAN BEFORE YOU DISCONNECT OR CONNECT THEM. CONTAMINATION ON THE ELECTRICAL CONNECTORS CAN CAUSE DAMAGE TO EQUIPMENT.
(2) Disconnect the electrical contacts (1) from the terminal block (2), use the ELEC CONTACTS INSERTION EXTRACTION TOOL M15570-20. (3) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(4) Cut and discard the TIE WRAPS (3) to release the cable (8).
(5) Push the quick-release fasteners (6) with the PIN - NON METALLIC to disengage them and remove the cover (5).
(6) Pull the wash table light (4) to release it from the clamps (7).
(7) Remove the wash table light (4).