Detailed Inspection of the Torque-Link Damper-Assemblies

TASK 32-11-27-210-001-A
Detailed Inspection of the Torque-Link Damper-Assemblies

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	SAFETY BARRIER(S)
No specific	AR	WARNING NOTICE(S)

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.14SBA1)	Textile-Lint free Cotton -

C. Referenced Information

REFERENCE	DESIGNATION
TASK 12-12-32-611-006-A	Replenishment of the MLG Torque Link Damper
TASK 32-00-00-481-001-A	Installation of the Safety Devices on the Landing Gears
TASK 32-11-29-000-001-A	Removal of the Torque Link Damper
TASK 32-11-29-400-001-A	Installation of the Torque Link Damper
Torque-Link Damper-Assembly ** ON A/C NOT FOR ALL
Torque-Link Damper-Assembly ** ON A/C NOT FOR ALL

3. Job Set-up
Subtask 32-11-27-941-055-A

A. Safety Precautions
(1) Put the SAFETY BARRIER(S) in position.
(2) Make sure that the ground safety locks are on the landing gear (Ref. AMM TASK 32-00-00-481-001).
(3) On the panel 400VU:

make sure that the landing-gear control-lever 6GA is in the DOWN position
put a WARNING NOTICE(S) in position to tell persons not to operate the landing gear.

4. Procedure
Subtask 32-11-27-210-055-A

A. Detailed Inspection of the Torque-Link Damper-Assemblies
(1) Clean the component interface and/or the adjacent area with a Textile-Lint free Cotton - (Material No.14SBA1) made moist with Non Aqueous Cleaner-General - - (Material No.08BAA9) .
(2) Make sure that the level indicator shows a level between the REFILL line and the FULL line. If the torque link damper is at the REFILL position fill the damper (Ref. AMM TASK 12-12-32-611-006).
(3) Examine the torque link dampers to make sure that:

there are no hydraulic leaks between the reservoir and the damper
there is no external damage of the damper assembly
the bolts are correctly safetied with lockwire
the cover is correctly installed and is not damaged
the labels and indicator level lines are clean and in the correct condition.

(4) If you find damage:

remove the component (Ref. AMM TASK 32-11-29-000-001)
find the cause of the fault and do a repair
install a serviceable component (Ref. AMM TASK 32-11-29-400-001).

5. Close-up
Subtask 32-11-27-942-054-A

A. Removal of Equipment
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the safety barriers.
(3) Remove the WARNING NOTICE(S).
(4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

[Rev.10 from 2021] 2026.04.01 00:40:52 UTC