Inspection of the MLG Side Stay Attachment Lug(s) after the Aircraft has gone off the Runway

TASK 32-11-00-220-004-A
Inspection of the MLG Side Stay Attachment Lug(s) after the Aircraft has gone off the Runway

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.

1. Reason for the Job

NOTE: Make sure that you read the instructions in Task 05-51-24-200-001-A (Inspection after Leaving Runway or Taxiway) before you do this task.

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 2M (6 FT)
No specific	AR	SAFETY BARRIER(S)
No specific	AR	WARNING NOTICE(S)

B. Referenced Information

REFERENCE	DESIGNATION
TASK 32-00-00-481-001-A	Installation of the Safety Devices on the Landing Gears
TASK 32-11-18-000-001-A	Removal of the MLG Side-Stay - Pre-EV MLG
TASK 32-11-18-000-001-A-01	Removal of the MLG Side Stay - Post-EV MLG
TASK 32-11-18-400-001-A	Installation of the MLG Side-Stay - Pre-EV MLG
TASK 32-11-18-400-001-A-01	Installation of the MLG Side Stay - Post-EV MLG
MLG Side-Stay Attachment Lug - Inspection Area

3. Job Set-up
Subtask 32-11-00-941-076-A

A. Safety Precautions
(1) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's instructions and your local regulations.
(2) Make sure that the ground safety locks are installed on the landing gear (Ref. AMM TASK 32-00-00-481-001).
(3) On the panel 400VU:

make sure that the landing-gear control-lever 6GA is in the DOWN position
put a WARNING NOTICE(S) in position to tell persons not to operate the landing gear.

(4) Put WARNING NOTICE(S)S in position to tell persons not to operate the landing gear doors.

Subtask 32-11-00-010-066-A

B. Get Access
(1) Put the ACCESS PLATFORM 2M (6 FT) in position adjacent to the applicable MLG.
(2) Disconnect the side-stay from the MLG side-stay lower attachment lug(s) and remove the lower cardan joint (Ref. AMM TASK 32-11-18-000-001).

4. Procedure
Subtask 32-11-00-220-065-B

A. Inspection of the MLG Side-Stay Attachment Lug
(1) Visually examine the MLG side-stay lower attachment lug. Look for signs of cracks in the paint finish, distortion, stress and fatigue.
(2) Measure the out-of-roundness of the internal diameter W, you must measure the two bushes. The internal diameter W must be round within 30 microns (1200 micro-inches).

5. Close-up
Subtask 32-11-00-410-064-A

A. Close Access
(1) Install the side-stay lower cardan joint and connect the side-stay (Ref. AMM TASK 32-11-18-400-001).

Subtask 32-11-00-942-077-A

B. Removal of Equipment
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the WARNING NOTICE(S).
(3) Remove the access platform(s).
(4) Remove the safety barriers.
(5) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

[Rev.10 from 2021] 2026.04.01 00:39:34 UTC