Installation of the Hydraulic Suction Tubes

TASK 29-11-49-400-010-A
Installation of the Hydraulic Suction Tubes

WARNING: DO NOT GET HYDRAULIC FLUID ON YOUR SKIN, IN YOUR EYES OR IN YOUR MOUTH. HYDRAULIC FLUID IS POISONOUS AND CAN GO THROUGH YOUR SKIN AND INTO YOUR BODY. FLUSH HYDRAULIC FLUID FROM YOUR EYES, MOUTH OR SKIN WITH WATER. GET MEDICAL AID IF YOU GET HYDRAULIC FLUID IN YOUR EYES OR MOUTH.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

CAUTION: DO NOT LET HYDRAULIC FLUID FALL ON THE ENGINE. UNWANTED HYDRAULIC FLUID MUST BE REMOVED IMMEDIATELY WITH A CLEAN LINT FREE CLOTH. THE FLUID CAN CAUSE DAMAGE TO THE SURFACE PROTECTION AND TO SOME PARTS.

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE
No specific	AR	CONTAINER 5 L (1.32 USGAL)
No specific	AR	WARNING NOTICE(S)
No specific	Torque wrench: range to between 110 and 90 lbf.in (1.24 and 1.02 m.daN )
No specific	Torque wrench: range to between 900 and 800 lbf.in (10.17 and 9.04 m.daN )
No specific	Torque wrench: range to between 1080 and 900 lbf.in (12.20 and 10.17 m.daN )
No specific	Torque wrench: range to between 1200 and 960 lbf.in (13.56 and 10.85 m.daN )
No specific	Torque wrench: range to between 1680 and 1520 lbf.in (18.98 and 17.18 m.daN )

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.V01-002)	cleaning fluid
(Material No.02ABA1)	Phosphate Ester Hydraulic Fluid-General Power - -
(Material No.14SBA1)	Textile-Lint free Cotton -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
195BB
FOR [1000EM1] (ENGINE-1)
437AL, 438AR

D. Referenced Information

REFERENCE	DESIGNATION
TASK 12-12-29-611-001-A	Fill the Hydraulic Fluid Reservoir with a Hand Pump
TASK 29-10-00-864-001-A	Depressurize the Green Hydraulic System
TASK 29-11-00-710-001-A	Operational Test of the Green Hydraulic System
TASK 29-11-49-000-010-A	Removal of the Hydraulic Suction Tubes
TASK 29-14-00-614-001-A	Depressurization of the Hydraulic Reservoirs
TASK 70-23-11-911-013-A	General Torque Tightening Techniques
Hydraulic Tube Details
Hydraulic Tube Details
Hydraulic Tube Details
FOR [1000EM1] (ENGINE-1)
TASK 71-13-00-010-010-A	Opening of the Fan Cowls 437AL(447AL),438AR(448AR)
TASK 71-13-00-410-010-A	Closing of the Fan Cowls 437AL(447AL),438AR(448AR)

3. Job Set-up
Subtask 29-11-49-860-050-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Make sure that the Green hydraulic system is depressurized (Ref. AMM TASK 29-10-00-864-001).
(2) Make sure that the Green hydraulic reservoir is depressurized (Ref. AMM TASK 29-14-00-614-001).
(3) Make sure that the WARNING NOTICE(S) is (are) in position to tell persons not to pressurize the Green hydraulic system:

on the ground service panel 197CB.

(4) Make sure that the WARNING NOTICE(S) is (are) in position on the access door 195BB to tell persons not to pressurize the Green hydraulic reservoir.

Subtask 29-11-49-941-054-A ** ON A/C NOT FOR ALL

B. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:

make sure that the WARNING NOTICE(S) is (are) in position to tell persons not to start the engine.

(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) Make sure that the WARNING NOTICE(S) is (are) in position to tell persons not to pressurize the Green hydraulic system:

in the cockpit, on the HYD section of the overhead panel 40VU.

(4) On the overhead maintenance panel 50VU:

make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.

(5) Make sure that the WARNING NOTICE(S) is (are) in position to tell persons not to energize the FADEC 1(2).
(6) Make sure that a CONTAINER 5 L (1.32 USGAL) is below the suction-hose adapter connection to the hydraulic pump.

Subtask 29-11-49-010-054-A ** ON A/C NOT FOR ALL

C. Get Access
(1) Make sure that the left fan-cowl door is open:
(a) FOR [1000EM1] (ENGINE-1)
make sure that the doors 437AL 438AR are open (Ref. AMM TASK 71-13-00-010-010).
(2) Make sure that a ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE is in position at the engine.

4. Procedure
Subtask 29-11-49-420-050-A ** ON A/C NOT FOR ALL

A. Installation of the Hydraulic Suction Tubes
(1) Remove the applicable covers/caps/plugs from the openings.
(2) Clean the replacement parts and their interfaces.
(a) Use a clean Textile-Lint free Cotton - (Material No.14SBA1) made moist with the cleaning fluid (Material No.V01-002) , to clean the replacement parts and their interfaces.
(b) Use a clean dry Textile-Lint free Cotton - (Material No.14SBA1) to remove the dirty cleaning fluid from the parts while they are wet.
(3) With the hydraulic fluid Phosphate Ester Hydraulic Fluid-General Power - - (Material No.02ABA1) used in the aircraft hydraulic system, lightly lubricate these parts of the hydraulic tube/hose:

The threads of the nuts and the faces of the nuts that touch other parts
The threads of the unions and the faces of the unions that touch other parts
The threads of the couplings and the faces of the couplings that touch other parts.

(4) Attach the quick release coupling to the hose.
(a) Attach the quick release coupling (1) to the end connector of the hose (12).
(b) Hold the quick release coupling (1) with an applicable wrench.
(c) TORQUE the connector nut of the hose (12) to between 1080 and 900 lbf.in (12.20 and 10.17 m.daN )

(Ref. AMM TASK 70-23-11-911-013).
(5) Install the hydraulic suction tubes.
(a) While you install these parts, make sure that their positions are the same as their positions before the removal (Ref. AMM TASK 29-11-49-000-010):

The clamps (17), (37) and (39)
The bolts (16), (36) and (40)
The hoses (12) and (9) and the tube (10).

(b) Install the tube (10):

Put the tube (10) in the correct position on the engine for its installation.
Attach the connector nut of the tube (10) to the union (33). Tighten the connector nut with your hand.
Hold the union (33) with an applicable wrench.
TORQUE the bulkhead union nut of the union (33) to between 1200 and 960 lbf.in (13.56 and 10.85 m.daN ) (Ref. AMM TASK 70-23-11-911-013).
Loosely assemble the two halves of the clamp (39) and the three bolts (40) to the raft (38).
Remove the safety ties from the clamp (39) and the raft (38).
Loosely assemble the two halves of the clamp (37) and the three bolts (36) to the raft (34).
Remove the safety ties from the clamp (37) and the raft (34).
Hold the union (33) with an applicable wrench.
TORQUE the connector nut of the tube (10) to between 1680 and 1520 lbf.in (18.98 and 17.18 m.daN ) (Ref. AMM TASK 70-23-11-911-013).
TORQUE the bolts (36) and (40) to between 110 and 90 lbf.in (1.24 and 1.02 m.daN ) (Ref. AMM TASK 70-23-11-911-013).

PRE SBN29-0266
Connect the hose (9) to the tube (10) and the union (56).
END OF PRE SBN29-0266
POST SBN29-0266
Connect the hose (9) to the tube (10) and the union (59).
END OF POST SBN29-0266
Hold the end of the tube (10) with an applicable wrench.
TORQUE the connector nut of the hose (9) to between 1680 and 1520 lbf.in (18.98 and 17.18 m.daN ) (Ref. AMM TASK 70-23-11-911-013).
PRE SBN29-0266
Hold the union (56) with an applicable wrench.
END OF PRE SBN29-0266
POST SBN29-0266
Hold the union (59) with an applicable wrench.
END OF POST SBN29-0266
TORQUE the connector nut of the hose (9) to between 900 and 800 lbf.in (10.17 and 9.04 m.daN ) (Ref. AMM TASK 70-23-11-911-013).

(d) Install the top hose (12).

Put the hose (12) in the correct position into the clamp (17) for its installation.
Connect the hose (12) to the union (33).
Hold the union (33) with an applicable wrench.
TORQUE the connector nut of the hose (12) to between 1680 and 1520 lbf.in (18.98 and 17.18 m.daN ) (Ref. AMM TASK 70-23-11-911-013).
Connect the quick release coupling (1) to the aircraft pylon interface.
Install the bolt (16) on the clamp (17).
TORQUE the bolt (16) to between 110 and 90 lbf.in (1.24 and 1.02 m.daN ) (Ref. AMM TASK 70-23-11-911-013).

(6) Remove the container.

Subtask 29-11-49-710-050-A ** ON A/C NOT FOR ALL

B. Operational Test
(1) Do the operational test of Green hydraulic system (Ref. AMM TASK 29-11-00-710-001).
(2) Make sure that there are no leaks from the connections.
(3) Make sure that the level of the hydraulic fluid in the Green reservoir is correct. If necessary, fill the reservoir (Ref. AMM TASK 12-12-29-611-001).

5. Close-up
Subtask 29-11-49-860-056-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Remove the access platform(s).
(2) Make sure that the work area is clean and clear of tools and other items.

Subtask 29-11-49-410-050-A ** ON A/C NOT FOR ALL

B. Close Access
(1) Close the fan cowls:
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR (Ref. AMM TASK 71-13-00-410-010).
(2) Close the door 195BB.

Subtask 29-11-49-942-053-A ** ON A/C NOT FOR ALL

C. Safety Precautions
(1) Remove the WARNING NOTICE(S).

[Rev.10 from 2021] 2026.04.01 00:17:31 UTC