Installation of the Bottom Case-Drain Hose/Tube Assembly
TASK 29-11-49-400-004-A
Installation of the Bottom Case-Drain Hose/Tube Assembly
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 29-11-49-860-093-A ** ON A/C NOT FOR ALL
Subtask 29-11-49-420-060-A ** ON A/C NOT FOR ALL
Subtask 29-11-49-860-094-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 00:17:09 UTC
Installation of the Bottom Case-Drain Hose/Tube Assembly
WARNING:
OBEY THE HYDRAULIC SAFETY PROCEDURES.
WARNING:
DO NOT TOUCH THE HYDRAULIC SYSTEM COMPONENTS FOR A SHORT TIME AFTER THE ENGINE IS SHUTDOWN. THE ENGINE COMPONENTS STAY HOT FOR SOME TIME AND CAN CAUSE INJURY.
CAUTION:
DO NOT LET HYDRAULIC FLUID FALL ON THE ENGINE. UNWANTED HYDRAULIC FLUID MUST BE REMOVED IMMEDIATELY WITH A CLEAN LINT FREE CLOTH. THE FLUID CAN CAUSE DAMAGE TO THE SURFACE PROTECTION AND TO SOME PARTS.
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 195BB | |
| FOR [1000EM1] (ENGINE-1) | |
| 437AL | |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 12-12-29-611-001-A | Fill the Hydraulic Fluid Reservoir with a Hand Pump |
| TASK 12-12-29-611-002-A | Fill the Hydraulic Fluid Reservoir with a Hydraulic Service Cart |
| TASK 29-10-00-864-001-A | Depressurize the Green Hydraulic System |
| TASK 29-11-00-710-001-A | Operational Test of the Green Hydraulic System |
| TASK 29-14-00-614-001-A | Depressurization of the Hydraulic Reservoirs |
| FOR [1000EM1] (ENGINE-1) | |
| TASK 71-13-00-010-040-B | Opening of the Fan Cowl Doors |
| TASK 71-13-00-410-040-B | Closing of the Fan Cowl Doors |
Subtask 29-11-49-860-093-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) Make sure that the Green hydraulic system is depressurized (Ref. AMM TASK 29-10-00-864-001).
(2) Make sure that the Green hydraulic reservoir is depressurized (Ref. AMM TASK 29-14-00-614-001).
(3) Make sure that the WARNING NOTICE(S) is (are) in position to tell persons not to pressurize the Green hydraulic system:
Subtask 29-11-49-941-070-A ** ON A/C NOT FOR ALL (1) Make sure that the Green hydraulic system is depressurized (Ref. AMM TASK 29-10-00-864-001).
(2) Make sure that the Green hydraulic reservoir is depressurized (Ref. AMM TASK 29-14-00-614-001).
(3) Make sure that the WARNING NOTICE(S) is (are) in position to tell persons not to pressurize the Green hydraulic system:
- on the ground service panel 197CB.
B. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(3) Make sure that the WARNING NOTICE(S) is (are) in position to tell persons not to pressurize the Green hydraulic system:
(6) Make sure that a CONTAINER 5 L (1.32 USGAL) is below the bottom case drain hose/tube.
Subtask 29-11-49-865-057-A ** ON A/C NOT FOR ALL (1) On the center pedestal, on the ENG panel 115VU:
- Make sure that the WARNING NOTICE(S) is (are) in position to tell persons not to start the engine.
(3) Make sure that the WARNING NOTICE(S) is (are) in position to tell persons not to pressurize the Green hydraulic system:
- In the cockpit, on the HYD section of the overhead panel 40VU.
- Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(6) Make sure that a CONTAINER 5 L (1.32 USGAL) is below the bottom case drain hose/tube.
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:
Subtask 29-11-49-010-070-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 121VU | HYDRAULIC/G HYD/PUMP ENG1/MONG | 1702GK | R34 |
D. Get Access
(1) Make sure that the left fan cowl door is open:
(a) FOR [1000EM1] (ENGINE-1)
make sure that the door 437AL is open (Ref. AMM TASK 71-13-00-010-040).
(2) Make sure that the ACCESS PLATFORM 1M (3 FT)-ADJUSTABLE is in position at the engine.
4. Procedure(1) Make sure that the left fan cowl door is open:
(a) FOR [1000EM1] (ENGINE-1)
make sure that the door 437AL is open (Ref. AMM TASK 71-13-00-010-040).
(2) Make sure that the ACCESS PLATFORM 1M (3 FT)-ADJUSTABLE is in position at the engine.
Subtask 29-11-49-420-060-A ** ON A/C NOT FOR ALL
A. Installation of the Bottom Case-Drain Hose/Tube
(1) Remove the protective covers from the bottom case-drain hose (5), the hydraulic filter assembly and the union in the hydraulic pump.
(2) Loosely connect the bottom case-drain hose (5) to the hydraulic filter assembly. Do not TORQUE the coupling nut at this time.
(3) Loosely connect the bottom case-drain hose (5) to the union in the hydraulic pump. Do not TORQUE the coupling nut at this time.
(4) Install the center mount clamp (25) as follows:
(a) Remove the bolt (10), washer (15) and nut (20) from the band on the center mount clamp (25).
(b) Open the band on the center mount clamp (25) and put the bottom case-drain hose (5) into the hole in the insert.
(c) Put the band on the insert and install the bolt (10), washer (15) and nut (20).
(d) Make sure that the center mount clamp is installed at a distance of 12.30 in. (312.42 mm) below the flange of the suction hose/tube.
(e) Make sure that the center mount clamp and hoses have a minimum clearance of 0.40 in. (10.16 mm) from the CFMI hose.
(f) TORQUE the nut (20) to between 90 and 75 lbf.in (1.02 and 0.85 m.daN )
.
(5) Make sure that the bottom case-drain hose (5) is in the correct position.
.
(7) Remove the container.
Subtask 29-11-49-710-061-A ** ON A/C NOT FOR ALL (1) Remove the protective covers from the bottom case-drain hose (5), the hydraulic filter assembly and the union in the hydraulic pump.
(2) Loosely connect the bottom case-drain hose (5) to the hydraulic filter assembly. Do not TORQUE the coupling nut at this time.
(3) Loosely connect the bottom case-drain hose (5) to the union in the hydraulic pump. Do not TORQUE the coupling nut at this time.
(4) Install the center mount clamp (25) as follows:
(a) Remove the bolt (10), washer (15) and nut (20) from the band on the center mount clamp (25).
(b) Open the band on the center mount clamp (25) and put the bottom case-drain hose (5) into the hole in the insert.
(c) Put the band on the insert and install the bolt (10), washer (15) and nut (20).
(d) Make sure that the center mount clamp is installed at a distance of 12.30 in. (312.42 mm) below the flange of the suction hose/tube.
(e) Make sure that the center mount clamp and hoses have a minimum clearance of 0.40 in. (10.16 mm) from the CFMI hose.
(f) TORQUE the nut (20) to between 90 and 75 lbf.in (1.02 and 0.85 m.daN )
. (5) Make sure that the bottom case-drain hose (5) is in the correct position.
NOTE: You can use a second WRENCH - TORQUE to hold the fittings when you torque the coupling nuts. This prevents damage to the hose.
(6) TORQUE the coupling nuts of the bottom case-drain hose (5) to between 245 and 215 lbf.in (2.77 and 2.43 m.daN )
. (7) Remove the container.
B. Operational Test
(1) Do the operational test of the Green hydraulic system (Ref. AMM TASK 29-11-00-710-001).
(2) During the dry motoring of the engine 1, make sure that there are no leaks from the case drain hose/tube.
(3) Make sure that the level of the hydraulic fluid in the Green reservoir is correct. If necessary, fill the reservoir (Ref. AMM TASK 12-12-29-611-001) or (Ref. AMM TASK 12-12-29-611-002).
5. Close-up(1) Do the operational test of the Green hydraulic system (Ref. AMM TASK 29-11-00-710-001).
(2) During the dry motoring of the engine 1, make sure that there are no leaks from the case drain hose/tube.
(3) Make sure that the level of the hydraulic fluid in the Green reservoir is correct. If necessary, fill the reservoir (Ref. AMM TASK 12-12-29-611-001) or (Ref. AMM TASK 12-12-29-611-002).
Subtask 29-11-49-860-094-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) Remove the access platform(s).
(2) Make sure that the work area is clean and clear of tools and other items.
Subtask 29-11-49-410-062-A ** ON A/C NOT FOR ALL (1) Remove the access platform(s).
(2) Make sure that the work area is clean and clear of tools and other items.
B. Close Access
(1) Close the left fan cowl door:
(a) FOR [1000EM1] (ENGINE-1)
close the door 437AL (Ref. AMM TASK 71-13-00-410-040).
(2) Close the door 195BB.
Subtask 29-11-49-942-063-A ** ON A/C NOT FOR ALL (1) Close the left fan cowl door:
(a) FOR [1000EM1] (ENGINE-1)
close the door 437AL (Ref. AMM TASK 71-13-00-410-040).
(2) Close the door 195BB.
C. Safety Precautions
(1) Remove the WARNING NOTICE(S).
(1) Remove the WARNING NOTICE(S).
Bottom Case-Drain Hose Assembly