DOC AIRBUS | AMM A320FRemoval of the Hydraulic Suction Hose
TASK 29-11-49-000-806-A
Removal of the Hydraulic Suction Hose
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 29-11-49-860-136-A ** ON A/C NOT FOR ALL
Subtask 29-11-49-020-125-B ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 00:17:42 UTC
Removal of the Hydraulic Suction Hose
WARNING:
WEAR APPLICABLE PERSONAL PROTECTIVE EQUIPMENT (PPE) WHEN YOU DO THIS TASK. BEFORE YOU USE PPE, READ, UNDERSTAND AND OBEY ALL INSTRUCTIONS FOR ITS USE. THESE INSTRUCTIONS INCLUDE INSTRUCTIONS FROM THE MANUFACTURER, YOUR EMPLOYER AND GOVERNMENT REGULATIONS. YOU CAN GET INJURED IF YOU DO NOT USE PPE. GET INSTRUCTIONS FROM YOUR EMPLOYER ON WHICH PPE IS NECESSARY.
WARNING:
YOU MUST NOT GET HYDRAULIC FLUID ON YOUR SKIN, IN YOUR EYES OR IN YOUR MOUTH. THE HYDRAULIC FLUID IS POISONOUS AND CAN BE ABSORBED INTO YOUR BODY. IF YOU ACCIDENTALLY GET HYDRAULIC FLUID IN YOUR EYES, MOUTH OR ON YOUR SKIN, FLUSH WITH WATER AND GET MEDICAL AID.
WARNING:
BE CAREFUL WHEN YOU DO WORK ON THE ENGINE AND THE ADJACENT COMPONENTS AFTER ENGINE SHUTDOWN. THE ENGINE, THE ENGINE OIL AND THE ADJACENT COMPONENTS CAN STAY HOT FOR A LONG TIME. IF YOU DO NOT OBEY THIS INSTRUCTION, INJURY CAN OCCUR.
WARNING:
OBEY THE HYDRAULIC SAFETY PROCEDURES.
ZONE: 413
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE |
| No specific | 1 | CONTAINER 5 L (1.32 USGAL) |
| No specific | AR | COVER - PROTECTION |
| No specific | AR | WARNING NOTICE(S) |
| No specific | 1 | WRENCH - STANDARD |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 413 | UPPER FWD PYLON |
| 195BB, 197CB | |
| FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1) | |
| 437AL, 438AR, 452AR | |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 29-10-00-864-001-A | Depressurize the Green Hydraulic System |
| TASK 29-14-00-614-001-A | Depressurization of the Hydraulic Reservoirs |
| TASK 71-00-00-860-833-A | Procedure to Prevent Engine Motoring |
| TASK 71-13-00-010-802-A | Opening of the Fan Cowl Doors |
| TASK 78-30-00-040-805-A | Deactivation of the Thrust Reverser System for Ground Maintenance |
| TASK 78-36-00-010-802-A | Opening of the Thrust Reverser Cowl-Doors |
Hydraulic Suction HoseSubtask 29-11-49-860-136-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) Make sure that the Green hydraulic system is depressurized
(Ref. AMM TASK 29-10-00-864-001).
(2) Depressurize the reservoir of the Green hydraulic system
(Ref. AMM TASK 29-14-00-614-001).
Subtask 29-11-49-941-108-A ** ON A/C NOT FOR ALL (1) Make sure that the Green hydraulic system is depressurized
(Ref. AMM TASK 29-10-00-864-001).
(2) Depressurize the reservoir of the Green hydraulic system
(Ref. AMM TASK 29-14-00-614-001).
B. Safety Precautions
(1) On AIR COND panel 30VU:
(a) Put WARNING NOTICE(S) in position to tell persons not to pressurize the Green hydraulic system on the ground service panel.
(3) On the HYD section of panel 40VU:
(a) Put a WARNING NOTICE(S) in position to tell persons not to pressurize the reservoir of the Green hydraulic system.
(5) Do the procedure to prevent engine motoring
(Ref. AMM TASK 71-00-00-860-833).
Subtask 29-11-49-010-123-A ** ON A/C NOT FOR ALL (1) On AIR COND panel 30VU:
- Make sure that the APU BLEED pushbutton switch is released (the ON legend is off).
- Put a WARNING NOTICE(S) in position to tell persons not to operate this pushbutton switch.
(a) Put WARNING NOTICE(S) in position to tell persons not to pressurize the Green hydraulic system on the ground service panel.
(3) On the HYD section of panel 40VU:
- Put WARNING NOTICE(S) in position to tell persons not to pressurize the Green hydraulic system.
(a) Put a WARNING NOTICE(S) in position to tell persons not to pressurize the reservoir of the Green hydraulic system.
(5) Do the procedure to prevent engine motoring
(Ref. AMM TASK 71-00-00-860-833).
C. Get Access
(1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL 438AR
Subtask 29-11-49-040-071-A ** ON A/C NOT FOR ALL (1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL 438AR
D. Deactivation of the Thrust Reverser for Maintenance
Subtask 29-11-49-010-124-A ** ON A/C NOT FOR ALL WARNING:
YOU MUST DEACTIVATE THE THRUST REVERSER BEFORE YOU DO WORK ON OR AROUND IT. IF YOU DO NOT, THE THRUST REVERSER CAN OPERATE ACCIDENTALLY AND CAUSE AN INJURY AND/OR DAMAGE.
(1) Do the deactivation of the thrust reverser system for maintenance (Ref. AMM TASK 78-30-00-040-805). E. Get Access
(1) Open the right thrust-reverser cowl-door (Ref. AMM TASK 78-36-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
452AR
(2) Put an ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position.
4. Procedure(1) Open the right thrust-reverser cowl-door (Ref. AMM TASK 78-36-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
452AR
(2) Put an ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position.
Subtask 29-11-49-020-125-B ** ON A/C NOT FOR ALL
A. Removal of the Hydraulic Suction hose
(a) Put a CONTAINER 5 L (1.32 USGAL) below the hydraulic suction hose (1) and the hydraulic pump.
(b) Hold the adapter with a WRENCH - STANDARD and disconnect the hydraulic suction hose (1) from the adapter.
(c) Drain the hydraulic fluid from the lower end of the hydraulic suction hose (1) into the CONTAINER 5 L (1.32 USGAL).
(d) Disconnect the quick disconnect coupling (2) on the hydraulic suction hose (1) from the pylon fuel-hydraulic panel.
(e) Remove the hydraulic suction hose (1) and quick disconnect coupling (2) from the engine.
(f) Remove the quick disconnect coupling (2) from the hydraulic suction hose (1).
(g) Drain the hydraulic fluid from the hydraulic suction hose (1) into the CONTAINER 5 L (1.32 USGAL).
(2) Installation of the protection covers
Subtask 29-11-49-020-125-C ** ON A/C NOT FOR ALL CAUTION:
USE A SECOND WRENCH TO HOLD THE MATING PARTS WHEN YOU LOOSEN OR TIGHTEN THE TUBE OR HOSE NUTS. IF YOU DO NOT OBEY THIS INSTRUCTION, YOU CAN TWIST THE TUBES OR HOSES OR CAUSE DAMAGE TO THEM.
CAUTION:
HYDRAULIC FLUID CAN CAUSE DAMAGE TO EQUIPMENT. IF HYDRAULIC FLUID FALLS ON A SURFACE, IMMEDIATELY CLEAN THE SURFACE WITH A CLEAN CLOTH.
(1) Remove the hydraulic suction hose (1). (a) Put a CONTAINER 5 L (1.32 USGAL) below the hydraulic suction hose (1) and the hydraulic pump.
(b) Hold the adapter with a WRENCH - STANDARD and disconnect the hydraulic suction hose (1) from the adapter.
(c) Drain the hydraulic fluid from the lower end of the hydraulic suction hose (1) into the CONTAINER 5 L (1.32 USGAL).
(d) Disconnect the quick disconnect coupling (2) on the hydraulic suction hose (1) from the pylon fuel-hydraulic panel.
(e) Remove the hydraulic suction hose (1) and quick disconnect coupling (2) from the engine.
(f) Remove the quick disconnect coupling (2) from the hydraulic suction hose (1).
(g) Drain the hydraulic fluid from the hydraulic suction hose (1) into the CONTAINER 5 L (1.32 USGAL).
(2) Installation of the protection covers
CAUTION:
INSTALL PROTECTION COVERS ON ALL THE OPENINGS IMMEDIATELY TO PREVENT DAMAGE TO THE ENGINE.
(a) Install COVER - PROTECTION on the pylon fuel-hydraulic panel interface, adapter, hydraulic suction hose (1) and quick disconnect coupling (2). A. Removal of the Hydraulic Suction hose
(a) Put a CONTAINER 5 L (1.32 USGAL) below the hydraulic suction hose (1) and the hydraulic pump.
(b) Hold the union with a WRENCH - STANDARD and disconnect the hydraulic suction hose (1) from the union on the hydraulic pump.
(c) Drain the hydraulic fluid from the lower end of the hydraulic suction hose (1) into the CONTAINER 5 L (1.32 USGAL).
(d) Disconnect the quick disconnect coupling (2) on the hydraulic suction hose (1) from the pylon fuel-hydraulic panel.
(e) Remove the hydraulic suction hose (1) and quick disconnect coupling (2) from the engine.
(f) Remove the quick disconnect coupling (2) from the hydraulic suction hose (1).
(g) Drain the hydraulic fluid from the hydraulic suction hose (1) into the CONTAINER 5 L (1.32 USGAL).
(2) Installation of the protection covers
CAUTION:
USE A SECOND WRENCH TO HOLD THE MATING PARTS WHEN YOU LOOSEN OR TIGHTEN THE TUBE OR HOSE NUTS. IF YOU DO NOT OBEY THIS INSTRUCTION, YOU CAN TWIST THE TUBES OR HOSES OR CAUSE DAMAGE TO THEM.
CAUTION:
HYDRAULIC FLUID CAN CAUSE DAMAGE TO EQUIPMENT. IF HYDRAULIC FLUID FALLS ON A SURFACE, IMMEDIATELY CLEAN THE SURFACE WITH A CLEAN CLOTH.
(1) Remove the hydraulic suction hose (1). (a) Put a CONTAINER 5 L (1.32 USGAL) below the hydraulic suction hose (1) and the hydraulic pump.
(b) Hold the union with a WRENCH - STANDARD and disconnect the hydraulic suction hose (1) from the union on the hydraulic pump.
(c) Drain the hydraulic fluid from the lower end of the hydraulic suction hose (1) into the CONTAINER 5 L (1.32 USGAL).
(d) Disconnect the quick disconnect coupling (2) on the hydraulic suction hose (1) from the pylon fuel-hydraulic panel.
(e) Remove the hydraulic suction hose (1) and quick disconnect coupling (2) from the engine.
(f) Remove the quick disconnect coupling (2) from the hydraulic suction hose (1).
(g) Drain the hydraulic fluid from the hydraulic suction hose (1) into the CONTAINER 5 L (1.32 USGAL).
(2) Installation of the protection covers
CAUTION:
INSTALL PROTECTION COVERS ON ALL THE OPENINGS IMMEDIATELY TO PREVENT DAMAGE TO THE ENGINE.
(a) Install COVER - PROTECTION on the pylon fuel-hydraulic panel interface, union on the hydraulic pump, hydraulic suction hose (1) and quick disconnect coupling (2).