Discard Solid Particle Filter
TASK 26-23-14-960-001-A
Discard Solid Particle Filter
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Work Zones and Access Panels
D. Expendable Parts
E. Referenced Information
3. Job Set-up
Subtask 26-23-14-861-054-A ** ON A/C NOT FOR ALL
Subtask 26-23-14-960-051-C ** ON A/C NOT FOR ALL
Subtask 26-23-14-865-062-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.03.31 23:46:05 UTC
Discard Solid Particle Filter
WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | SAFETY CLIP - CIRCUIT BREAKER |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.02BBB9) | Mineral Hydraulic Fluid-Damper - - |
| (Material No.14QFB1) | Wire-Locking Dia: 0.8 mm CRES Nickel Alloy - |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 152 | AFT CARGO COMPARTMENT |
| 162 | BULK CARGO COMPARTMENT |
| 172 | AFT CABIN U/FLOOR COMPARTMENT |
| 162CW | |
| 161DW | |
| 132MW, 825 | |
| 826 |
| FIG.ITEM | DESIGNATION | IPC-CSN |
|---|---|---|
| 3 | SOLID-PARTICLE FILTER ELEMENT | AIPC 26-23-14-01-040 |
| 2 | O-RING | AIPC 26-23-14-01-050 |
| 3 | SOLID-PARTICLE FILTER ELEMENT | AIPC 26-23-14-20-020 |
| 2 | O-RING | AIPC 26-23-14-20-050 |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-42-00-861-001-A | Energize the Ground Service Network from the External Power |
| TASK 24-42-00-862-001-A | De-energize the Ground Service Network Supplied from the External Power |
| TASK 25-28-41-000-001-A | Removal of the Textile Floor Covering |
| TASK 25-28-41-400-001-A | Installation of the Textile Floor Covering |
| TASK 25-54-12-000-003-A | Removal of the Sidewall Panels in the Forward Cargo Compartment |
| TASK 25-54-12-400-003-A | Installation of the Sidewall Panels in the Forward Cargo Compartment |
| TASK 25-55-12-000-001-A | Removal of the Aft Cargo-Compartment Partition at FR65 |
| TASK 25-55-12-000-003-A | Removal of the Sidewall Panels in the Aft Cargo Compartment - FR59/FR65 |
| TASK 25-55-12-400-001-A | Installation of the Aft Cargo-Compartment Partition at FR65 |
| TASK 25-55-12-400-003-A | Installation of the Sidewall Panels in the Aft Cargo Compartment - FR59/FR65 |
| TASK 52-30-00-860-001-A | Open the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump |
| TASK 52-30-00-860-002-A | Close the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump |
| TASK 53-42-12-000-001-A | Removal of the Cabin Floor Panels from FR47 thru FR64 |
| TASK 53-42-12-400-001-A | Installation of the Cabin Floor Panels from FR47 thru FR64 |
Subtask 26-23-14-861-054-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) Energize the ground service network
(Ref. AMM TASK 24-42-00-861-001).
Subtask 26-23-14-865-061-A ** ON A/C NOT FOR ALL (1) Energize the ground service network
(Ref. AMM TASK 24-42-00-861-001).
B. Open, safety and tag this(these) circuit breaker(s):
Subtask 26-23-14-010-062-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | AIR COND/CARGO FIRE/EXTIG/BTL1 | 1WX | C03 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | AIR COND/CIDS/SDF/DIR2 ESS | 18WH | C06 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | AIR COND/SDCU/CHAN1 | 11WQ | C06 |
| 49VU | AIR COND/CARGO FIRE/EXTIG/BTL2 | 8WX | C05 |
| 49VU | AIR COND/CARGO/FIRE/EXTIG/BTL1 | 1WX | C04 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | AIR COND/CARGO FIRE/EXTIG/BTL2 | 8WX | C04 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | AIR COND/CARGO/FIRE/EXTIG/BTL1 | 1WX | C03 |
| ** ON A/C NOT FOR ALL | |||
| 122VU | AIR COND/CIDS/SDF/DIR NORM/1 | 17WH | T17 |
| ** ON A/C NOT FOR ALL | |||
| 122VU | AIR COND/SDCU/CHAN2 | 12WQ | T18 |
| ** ON A/C NOT FOR ALL | |||
| 122VU | AIR COND/CARGO/FIRE/EXTIG | 1WX | T19 |
C. Get Access
(1) Open the forward cargo-compartment door 825 (Ref. AMM TASK 52-30-00-860-001).
(2) Set the CARGO COMPT LIGHT switch 6LU to the ON position.
(3) Remove the sidewall panel 132MW (Ref. AMM TASK 25-54-12-000-003).
Subtask 26-23-14-010-062-D ** ON A/C NOT FOR ALL (1) Open the forward cargo-compartment door 825 (Ref. AMM TASK 52-30-00-860-001).
(2) Set the CARGO COMPT LIGHT switch 6LU to the ON position.
(3) Remove the sidewall panel 132MW (Ref. AMM TASK 25-54-12-000-003).
C. Get Access
(1) Open the aft cargo-compartment door 826 (Ref. AMM TASK 52-30-00-860-001).
(2) Set the CARGO COMPT LIGHT switch 8LU to the ON position.
(3) Remove the partition panel 161DW (Ref. AMM TASK 25-55-12-000-001).
Subtask 26-23-14-010-062-F ** ON A/C NOT FOR ALL (1) Open the aft cargo-compartment door 826 (Ref. AMM TASK 52-30-00-860-001).
(2) Set the CARGO COMPT LIGHT switch 8LU to the ON position.
(3) Remove the partition panel 161DW (Ref. AMM TASK 25-55-12-000-001).
C. Get Access
(1) For aircraft without Additional Center Tanks (ACT) 1 and 2 installed:
(a) Open aft cargo-compartment door 826 (Ref. AMM TASK 52-30-00-860-001).
(b) Set CARGO COMPT LIGHT switch 8LU to the ON position.
(c) Remove sidewall panel 162CW (Ref. AMM TASK 25-55-12-000-003).
(2) For aircraft with ACT 1 and 2 installed:
(a) In the aft cabin, remove the center textile-floor covering between frames 62 and 64 (Ref. AMM TASK 25-28-41-000-001).
(b) Remove floor panel 251DH (Ref. AMM TASK 53-42-12-000-001).
(c) Remove access panel 161EC from the ceiling of the aft cargo compartment.
(d) In the bulk cargo compartment, remove sidewall panel 162CW (Ref. AMM TASK 25-55-12-000-003).
4. Procedure(1) For aircraft without Additional Center Tanks (ACT) 1 and 2 installed:
(a) Open aft cargo-compartment door 826 (Ref. AMM TASK 52-30-00-860-001).
(b) Set CARGO COMPT LIGHT switch 8LU to the ON position.
(c) Remove sidewall panel 162CW (Ref. AMM TASK 25-55-12-000-003).
(2) For aircraft with ACT 1 and 2 installed:
(a) In the aft cabin, remove the center textile-floor covering between frames 62 and 64 (Ref. AMM TASK 25-28-41-000-001).
(b) Remove floor panel 251DH (Ref. AMM TASK 53-42-12-000-001).
(c) Remove access panel 161EC from the ceiling of the aft cargo compartment.
(d) In the bulk cargo compartment, remove sidewall panel 162CW (Ref. AMM TASK 25-55-12-000-003).
Subtask 26-23-14-960-051-C ** ON A/C NOT FOR ALL
A. Replacement of the Solid-Particle Filter
(2) Remove the filter bowl (4) from the filter head (1).
(3) Remove and discard the o-ring (2) and the solid-particle filter element (3).
(4) Make sure that the filter bowl (4) and the filter head (1) are clean and in the correct condition.
(5) Apply hydraulic fluid:
(6) Install the new o-ring (2) on the filter head (1).
(7) Install the new AIPC 26-23-14-01-040 SOLID-PARTICLE FILTER ELEMENT (3) together with the filter bowl (4) on the filter head (1).
14QFB1 Wire-Locking Dia: 0.8 mm CRES Nickel Alloy - .
Subtask 26-23-14-960-051-D ** ON A/C NOT FOR ALL WARNING:
USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.
(1) Remove and discard the lockwire from the filter bowl (4). (2) Remove the filter bowl (4) from the filter head (1).
(3) Remove and discard the o-ring (2) and the solid-particle filter element (3).
(4) Make sure that the filter bowl (4) and the filter head (1) are clean and in the correct condition.
(5) Apply hydraulic fluid:
CAUTION:
APPLY A SMALL QUANTITY OF THE CORRECT HYDRAULIC FLUID ON THE O-RING. THIS WILL PREVENT DAMAGE TO IT. MAKE SURE THAT HYDRAULIC FLUID DOES NOT GO INTO THE FILTER. HYDRAULIC FLUID IN THE FILTER CAN CAUSE A MALFUNCTION OF THE SYSTEM.
(a) Apply a small quantity of Mineral Hydraulic Fluid-Damper - - (Material No.02BBB9) to the new AIPC 26-23-14-01-050 O-RING (2). (6) Install the new o-ring (2) on the filter head (1).
(7) Install the new AIPC 26-23-14-01-040 SOLID-PARTICLE FILTER ELEMENT (3) together with the filter bowl (4) on the filter head (1).
WARNING:
USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.
(8) Safety the filter bowl (4) with lockwire A. Replacement of the Solid Particle Filter
(2) Remove the filter bowl (4) from the filter head (1).
(3) Remove and discard the o-ring (2) and the solid-particle filter element (3).
(4) Make sure that the filter bowl (4) and the filter head (1) are clean and in the correct condition.
(5) Apply hydraulic fluid:
(6) Install the new o-ring (2) on the filter head (1).
(7) Install the new AIPC 26-23-14-20-020 SOLID-PARTICLE FILTER ELEMENT (3) together with the filter bowl (4) on the filter head (1).
14QFB1 Wire-Locking Dia: 0.8 mm CRES Nickel Alloy - .
5. Close-upWARNING:
USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.
(1) Remove and discard the lockwire from the filter bowl (4). (2) Remove the filter bowl (4) from the filter head (1).
(3) Remove and discard the o-ring (2) and the solid-particle filter element (3).
(4) Make sure that the filter bowl (4) and the filter head (1) are clean and in the correct condition.
(5) Apply hydraulic fluid:
CAUTION:
APPLY A SMALL QUANTITY OF THE CORRECT HYDRAULIC FLUID ON THE O-RING. THIS WILL PREVENT DAMAGE TO IT. MAKE SURE THAT HYDRAULIC FLUID DOES NOT GO INTO THE FILTER. HYDRAULIC FLUID IN THE FILTER CAN CAUSE A MALFUNCTION OF THE SYSTEM.
(a) Apply a small quantity of Mineral Hydraulic Fluid-Damper - - (Material No.02BBB9) to the new AIPC 26-23-14-20-050 O-RING (2). (6) Install the new o-ring (2) on the filter head (1).
(7) Install the new AIPC 26-23-14-20-020 SOLID-PARTICLE FILTER ELEMENT (3) together with the filter bowl (4) on the filter head (1).
WARNING:
USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.
(8) Safety the filter bowl (4) with lockwire Subtask 26-23-14-865-062-A ** ON A/C NOT FOR ALL
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
Subtask 26-23-14-410-057-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | AIR COND/CARGO FIRE/EXTIG/BTL1 | 1WX | C03 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | AIR COND/CIDS/SDF/DIR2 ESS | 18WH | C06 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | AIR COND/SDCU/CHAN1 | 11WQ | C06 |
| 49VU | AIR COND/CARGO FIRE/EXTIG/BTL2 | 8WX | C05 |
| 49VU | AIR COND/CARGO/FIRE/EXTIG/BTL1 | 1WX | C04 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | AIR COND/CARGO FIRE/EXTIG/BTL2 | 8WX | C04 |
| ** ON A/C NOT FOR ALL | |||
| 49VU | AIR COND/CARGO/FIRE/EXTIG/BTL1 | 1WX | C03 |
| ** ON A/C NOT FOR ALL | |||
| 122VU | AIR COND/CIDS/SDF/DIR NORM/1 | 17WH | T17 |
| ** ON A/C NOT FOR ALL | |||
| 122VU | AIR COND/SDCU/CHAN2 | 12WQ | T18 |
| ** ON A/C NOT FOR ALL | |||
| 122VU | AIR COND/CARGO/FIRE/EXTIG | 1WX | T19 |
B. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the sidewall panel 132MW (Ref. AMM TASK 25-54-12-400-003).
(3) Set the CARGO COMPT LIGHT switch 6LU to the OFF position.
(4) Close the forward cargo-compartment door 825 (Ref. AMM TASK 52-30-00-860-002).
Subtask 26-23-14-410-057-D ** ON A/C NOT FOR ALL (1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the sidewall panel 132MW (Ref. AMM TASK 25-54-12-400-003).
(3) Set the CARGO COMPT LIGHT switch 6LU to the OFF position.
(4) Close the forward cargo-compartment door 825 (Ref. AMM TASK 52-30-00-860-002).
B. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the partition panel 161DW (Ref. AMM TASK 25-55-12-400-001).
(3) Set the CARGO COMPT LIGHT switch 8LU to the OFF position.
(4) Close the aft cargo-compartment door 826 (Ref. AMM TASK 52-30-00-860-002).
Subtask 26-23-14-410-057-F ** ON A/C NOT FOR ALL (1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the partition panel 161DW (Ref. AMM TASK 25-55-12-400-001).
(3) Set the CARGO COMPT LIGHT switch 8LU to the OFF position.
(4) Close the aft cargo-compartment door 826 (Ref. AMM TASK 52-30-00-860-002).
B. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) For aircraft without ACT 1 and 2 installed:
(a) Install sidewall panel 162CW (Ref. AMM TASK 25-55-12-400-003).
(b) Set CARGO COMPT LIGHT switch 8LU to the OFF position.
(c) Close aft cargo-compartment door 826 (Ref. AMM TASK 52-30-00-860-002).
(3) For aircraft with ACT 1 and 2 installed:
(a) In the bulk cargo compartment, install sidewall panel 162CW (Ref. AMM TASK 25-55-12-400-003).
(b) Install access panel 161EC from the ceiling of the aft cargo compartment.
(c) In the cabin, install floor panel 251DH (Ref. AMM TASK 53-42-12-400-001).
(d) Install the center textile-floor covering between frames 62 and 64 (Ref. AMM TASK 25-28-41-400-001).
Subtask 26-23-14-862-053-A ** ON A/C NOT FOR ALL (1) Make sure that the work area is clean and clear of tools and other items.
(2) For aircraft without ACT 1 and 2 installed:
(a) Install sidewall panel 162CW (Ref. AMM TASK 25-55-12-400-003).
(b) Set CARGO COMPT LIGHT switch 8LU to the OFF position.
(c) Close aft cargo-compartment door 826 (Ref. AMM TASK 52-30-00-860-002).
(3) For aircraft with ACT 1 and 2 installed:
(a) In the bulk cargo compartment, install sidewall panel 162CW (Ref. AMM TASK 25-55-12-400-003).
(b) Install access panel 161EC from the ceiling of the aft cargo compartment.
(c) In the cabin, install floor panel 251DH (Ref. AMM TASK 53-42-12-400-001).
(d) Install the center textile-floor covering between frames 62 and 64 (Ref. AMM TASK 25-28-41-400-001).
C. Put the aircraft back to its initial configuration.
(1) De-energize the ground service network
(Ref. AMM TASK 24-42-00-862-001).
(1) De-energize the ground service network
(Ref. AMM TASK 24-42-00-862-001).
Solid-Particle Filter