Apply Temporary Protection to the End Fittings of Electrical Conduits in the Air Conditioning Compartment

TASK 24-92-00-210-007-A
Apply Temporary Protection to the End Fittings of Electrical Conduits in the Air Conditioning Compartment

WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND THE CAUTIONS INCLUDED IN THE REFERENCED PROCEDURES.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

ZONE: 191
ZONE: 192

1. Reason for the Job
Refer to the MPD TASK: 240000-11
APPLY TEMPORARY PROTECTION TO END FITTINGS OF ELECTRICAL CONDUITS IN AIR CONDITIONING COMPARTMENT
Protection of the end fittings of the electrical conduits in the air conditioning compartment with temporary protective material
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE
No specific	AR	BRUSH - BRISTLED
No specific	AR	SPRAY - BOTTLE, PUMP TYPE (NON AEROSOL)

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.12ACB1)	Corrosion Preventive Compound-Heavy Duty Hard Film -
(Material No.14SBA1)	Textile-Lint free Cotton -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
191	AIR CONDITIONING COMPT AND FAIRINGS
192	AIR CONDITIONING COMPT AND FAIRINGS
191BB, 191KB, 192FB, 192KB

D. Referenced Information

REFERENCE	DESIGNATION
TASK 12-34-24-869-002-A	Aircraft Grounding (Earthing) for the Maintenance Operations
TASK 12-34-24-869-002-A-01	Aircraft Grounding (Earthing) during Transit, Turnaround or Overnight Stop
TASK 24-41-00-862-002-A	De-energize the Aircraft Electrical Circuits Supplied from the External Power
TASK 24-41-00-862-002-A-01	De-energize the Aircraft Electrical Circuits Supplied from the APU
TASK 24-41-00-862-002-A-02	De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2)
TASK 32-12-00-010-001-A	Open the Main Gear Doors for Access
TASK 32-12-00-410-001-A	Close the Main Gear Doors after Access
TASK 53-35-13-000-002-A	Removal of the Quick-Release Access Panels from the Belly Fairing Structure
TASK 53-35-13-400-002-A	Installation of the Quick-Release Access Panels on the Belly Fairing Structure
ESPM 203330
Electrical Harness Conduits - Corrosion Protection
Typical Fittings
Location of Conduit Fittings

3. Job Set-up
Subtask 24-92-00-862-056-A

A. De-energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-862-002).

Subtask 24-92-00-869-063-A

B. Connect the aircraft to the ground (Ref. AMM TASK 12-34-24-869-002).

Subtask 24-92-00-010-056-A

C. Get Access
(1) Put the ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position at the wing and the center fuselage.
(2) For the center fuselage.
(a) Remove the access panels: 191BB, 191KB, 192FB, 192KB (Ref. AMM TASK 53-35-13-000-002).
(b) Open the L and R main landing-gear doors at zone 734 and 744 (Ref. AMM TASK 32-12-00-010-001).

4. Procedure
Subtask 24-92-00-210-056-A

A. Protection of the End Fittings of the Electrical Conduits in the Air Conditioning Compartment with Temporary Protective Material

Electrical Harness Conduits - Corrosion Protection

Typical Fittings

Location of Conduit Fittings

WARNING: BE CAREFUL NOT TO CUT YOUR FINGERS. FLAKES OF NICKEL ARE SHARP.

(1) At each fitting use the procedure that follows to protect against corrosion:
(a) Use Non Aqueous Cleaner-General - - (Material No.08BAA9) and a Textile-Lint free Cotton - (Material No.14SBA1) to remove any contamination from the fitting.
(b) Remove any flakes or blisters, make sure that the you do not damage the base metal while you do this task.

NOTE: We recommend that you use a dental tool or a seal tool (non metallic) to remove the flakes and the blisters.

(c) Use a BRUSH - BRISTLED or an SPRAY - BOTTLE, PUMP TYPE (NON AEROSOL) to apply a continuous thin and smooth coat of Corrosion Preventive Compound-Heavy Duty Hard Film - (Material No.12ACB1) , to cover all the fitting ESPM 203330.

5. Close-up
Subtask 24-92-00-410-057-A

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) For the center fuselage.
(a) Install the access panels: 191BB, 191KB, 192FB, 192KB (Ref. AMM TASK 53-35-13-400-002).
(b) Close the L and R main landing-gear doors at zone 734 and 744 (Ref. AMM TASK 32-12-00-410-001).
(3) Disconnect the aircraft from the ground (Ref. AMM TASK 12-34-24-869-002).
(4) Remove the access platform(s).

[Rev.10 from 2021] 2026.03.31 23:25:45 UTC