General Visual Inspection of Flap Track No 2 and Fairing (EWIS)

TASK 05-25-30-200-001-A
General Visual Inspection of Flap Track No 2 and Fairing (EWIS)

WARNING: DO NOT EXTEND THE SLATS AND FLAPS WHEN THE THRUST REVERSER COWLS ARE DEPLOYED. IF YOU DO NOT OBEY THIS WARNING, YOU CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO THE COMPONENTS.

WARNING: MAKE SURE THAT THE SAFETY DEVICES AND THE WARNING NOTICES ARE IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.

ZONE: 531
ZONE: 631

1. Reason for the Job
Refer to the MPD TASK: ZL-531-01
GENERAL VISUAL INSPECTION OF FLAP TRACK NO 2 AND FAIRING (EWIS)

NOTE: This is an EWIS (Electrical Wiring Interconnection System) procedure. EWIS is defined in ESPM 20-33-11.

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 3M (10 FT)
No specific	AR	WARNING NOTICE(S)
98L12003001000	AR	HARNESS,SAFETY

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
531	FLAP TRACK 2 FAIRING
631	FLAP TRACK 2 FAIRING
531AT, 631AT

C. Referenced Information

REFERENCE	DESIGNATION
TASK 27-50-00-866-008-A	Extension of the Flaps on the Ground
TASK 27-50-00-866-008-A-01	Extension of the Flaps/Slats on the Ground
TASK 27-50-00-866-009-A	Retraction of the Flaps on the Ground
TASK 27-50-00-866-009-A-01	Retraction of the Flaps/Slats on the Ground
TASK 57-55-11-000-001-A	Removal of the Flap Track Fairings Nos. 2, 3 and 4
TASK 57-55-11-000-004-A	Removal of the Flap Track Fairings Nos. 2, 3 and 4
TASK 57-55-11-400-001-A	Installation of the Flap Track Fairings Nos. 2, 3 and 4
TASK 57-55-11-400-004-A	Installation of the Flap Track Fairings Nos. 2, 3 and 4
Access Panels of the Flap Track Fairings ** ON A/C NOT FOR ALL
Access Panels of the Flap Track Fairings ** ON A/C NOT FOR ALL
Flap Track No. 2 and Fairing

3. Job Set-up
Subtask 05-25-30-010-050-A ** ON A/C NOT FOR ALL

A. Get Access
(1) Put the ACCESS PLATFORM 3M (10 FT) in position.

WARNING: BEFORE YOU START WORK, YOU MUST PUT ON A SAFETY HARNESS AND ATTACH IT TO THE ACCESS PLATFORM. WITHOUT A SAFETY HARNESS, YOU CAN FALL. THIS CAN KILL YOU OR CAUSE YOU INJURY.

(2) Put on and attach the HARNESS, SAFETY before you start work in the work area.
(3) Remove access panels 531AT and 631AT (Ref. AMM TASK 57-55-11-000-001).

Access Panels of the Flap Track Fairings ** ON A/C NOT FOR ALL

Subtask 05-25-30-010-050-B ** ON A/C NOT FOR ALL

A. Get Access
(1) Put the ACCESS PLATFORM 3M (10 FT) in position.

WARNING: BEFORE YOU START WORK, YOU MUST PUT ON A SAFETY HARNESS AND ATTACH IT TO THE ACCESS PLATFORM. WITHOUT A SAFETY HARNESS, YOU CAN FALL. THIS CAN KILL YOU OR CAUSE YOU INJURY.

(2) Put on and attach the HARNESS, SAFETY before you start work in the work area.
(3) Remove access panels 531AT and 631AT (Ref. AMM TASK 57-55-11-000-004).

Access Panels of the Flap Track Fairings ** ON A/C NOT FOR ALL

Subtask 05-25-30-866-050-A

B. Aircraft Maintenance Configuration
(1) Fully extend the flaps (Ref. AMM TASK 27-50-00-866-008).

Subtask 05-25-30-941-074-A

C. Safety Precautions
(1) Put the WARNING NOTICE(S) in the cockpit to tell persons not to operate the flight controls.

4. Procedure
Subtask 05-25-30-210-050-A

A. Inspection

Flap Track No. 2 and Fairing

(1) Do a general visual inspection of flap track no. 2 and the related fairing.
(2) Make sure that there are no signs of corrosion, cracks or damage on all the parts of the components and the structure that you can see.
(3) Make sure that all the installations (wiring) are correctly attached.

5. Close-up
Subtask 05-25-30-866-051-A

A. Aircraft Maintenance Configuration
(1) Fully retract the flaps (Ref. AMM TASK 27-50-00-866-009).

Subtask 05-25-30-410-050-A ** ON A/C NOT FOR ALL

B. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Install access panels 531AT and 631AT (Ref. AMM TASK 57-55-11-400-001).
(3) Remove the access platform(s).

Subtask 05-25-30-410-050-B ** ON A/C NOT FOR ALL

B. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Install access panels 531AT and 631AT (Ref. AMM TASK 57-55-11-400-004).
(3) Remove the access platform(s).

Subtask 05-25-30-942-068-A

C. Put the Aircraft back to its Initial Configuration

(1) Remove the WARNING NOTICE(S).
(2) Remove all the fixtures, tools, test and support equipment used during this procedure.

[Rev.10 from 2021] 2026.03.31 22:50:11 UTC