Installation of the Kicker Plate from the Blocker Door [CFMB]

TASK 78-32-41-400-004-A
Installation of the Kicker Plate from the Blocker Door

FIN: 1000EM1 ** ON A/C NOT FOR ALL
FIN: 1000EM2 ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 1M(3 FT)
No specific	AR	WARNING NOTICE(S)
HIX3005	1	SAFETY SLEEVE - PIVOTING DOOR ACTUATOR

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL, 438AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR

C. Expendable Parts

FIG.ITEM	DESIGNATION	IPC-CSN
10	NUTS	AIPC 78-32-41-01-280
40	NUTS	AIPC 78-32-41-01-280

D. Referenced Information

REFERENCE	DESIGNATION
TASK 71-13-00-010-040-B	Opening of the Fan Cowl Doors
TASK 71-13-00-410-040-B	Closing of the Fan Cowl Doors
TASK 78-30-00-081-041-B	Make the Thrust Reverser Serviceable after Maintenance
TASK 78-30-00-481-041-B	Make the Thrust Reverser Unserviceable for Maintenance
TASK 78-32-41-080-001-A	Removal of the Safety Sleeve from Blocker Door Actuator
TASK 78-32-41-820-001-A	Alignment of the Blocker Door
TASK 78-32-41-860-002-A	Manual Stowing of the Blocker Door
Blocker Door Kicker Plates

3. Job Set-up
Subtask 78-32-41-860-056-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a WARNING NOTICE(S) is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a WARNING NOTICE(S) is in position to tell persons not to energize the FADEC 1(2).
(3) Make sure that the ACCESS PLATFORM 1M(3 FT) is in position.

Subtask 78-32-41-010-066-A ** ON A/C NOT FOR ALL

B. Make sure that the fan cowl doors are open (Ref. AMM TASK 71-13-00-010-040):
(1) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(2) FOR [1000EM2] (ENGINE-2)
447AL 448AR

Subtask 78-32-41-040-065-A ** ON A/C NOT FOR ALL

C. Make sure that the thrust reverser is unserviceable (Ref. AMM TASK 78-30-00-481-041).

4. Procedure
Subtask 78-32-41-420-053-A ** ON A/C NOT FOR ALL

A. Installation of the Kicker Plate on the Blocker Door

CAUTION: DO NOT PUSH ON THE STOW SWITCH LEVER WHEN BLOCKER DOOR IS OPENED OR DAMAGE COULD OCCUR.

(1) Install the Kicker Plate on the Blocker Door.
(2) Install the screws (30), (60), the washers (20), (50) and new AIPC 78-32-41-01-280 NUTS (10) and AIPC 78-32-41-01-280 NUTS (40).
(3) Torque the outer nut:

CAUTION: TAKE CARE NOT TO SCREW ON THE INNER NUT OR KICKER PLATE, DAMAGE CAN OCCUR.

(a) Install an hexagonal driver of 2 mm (0.08 in.) into the threaded stem.
(b) Hold the driver and torque the outer nut until it breaks off.
(4) Remove the HIX3005 SAFETY SLEEVE - PIVOTING DOOR ACTUATOR from the blocker door actuator without making thrust reverser operational (Ref. AMM TASK 78-32-41-080-001).
(5) Install the upper blocker door:

CAUTION: BLOCKER DOOR LATCH MUST BE OPENED WHEN YOU CLOSE THE BLOCKER DOOR OR DAMAGE CAN OCCUR.

(a) Manually move the blocker door to the closed position (Ref. AMM TASK 78-32-41-860-002).
(6) Make sure that the blocker door is correctly aligned (Ref. AMM TASK 78-32-41-820-001).

5. Close-up
Subtask 78-32-41-440-058-A ** ON A/C NOT FOR ALL

A. Make the thrust reverser serviceable (Ref. AMM TASK 78-30-00-081-041).

Subtask 78-32-41-410-059-A ** ON A/C NOT FOR ALL

B. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the fan cowl doors (Ref. AMM TASK 71-13-00-410-040):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(3) Remove the access platform(s).
(4) Remove the WARNING NOTICE(S).

[Rev.10 from 2021] 2026.04.01 03:26:06 UTC