Removal of the Exhaust Gas Temperature (EGT) (T5/T3) Wiring Harness (WC05) [PW11]

TASK 77-21-61-000-802-A
Removal of the Exhaust Gas Temperature (EGT) (T5/T3) Wiring Harness (WC05)

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE AFTER SHUTDOWN. THE ENGINE CAN STAY HOT FOR A LONG TIME. IF YOU DO NOT OBEY THIS INSTRUCTION, INJURY CAN OCCUR.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

CAUTION: DO NOT BEND OR TWIST THE HARNESS TOO MUCH. IF YOU DO, DAMAGE TO THE HARNESS CAN OCCUR.

ZONE: 400
FIN: 4207KS ** ON A/C NOT FOR ALL

1. Reason for the Job
Use this procedure to replace the Exhaust Gas Temperature (EGT) (T5/T3) wiring harness (WC05).
For more information on the temperature indicating system, refer to (77-00-00-00U).
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 1M(3 FT)
No specific	1	COVER - PROTECTION
No specific	1	PLIERS - JAWED, SOFT

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
400	POWER PLANT, NACELLES AND PYLONS
FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL, 438AR, 451AL, 452AR
FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL, 448AR, 461AL, 462AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 71-00-00-860-832-A	Procedure to Prevent Engine Motoring and to Stop the Electrical Supply to the EEC
TASK 71-13-00-010-802-A	Opening of the Fan Cowl Doors
TASK 78-30-00-040-805-A	Deactivation of the Thrust Reverser System for Ground Maintenance
TASK 78-36-00-010-802-A	Opening of the Thrust Reverser Cowl-Doors
Exhaust Gas Temperature (EGT) (T5/T3) Wiring Harness (WC05)

3. Job Set-up
Subtask 77-21-61-941-052-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) Do the procedure to prevent engine motoring and to stop the electrical supply to the Electronic Engine Control (EEC)
(Ref. AMM TASK 71-00-00-860-832).

Subtask 77-21-61-010-054-A ** ON A/C NOT FOR ALL

B. Get Access
(1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL, 438AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL, 448AR
(2) Put an ACCESS PLATFORM 1M(3 FT) in position.

Subtask 77-21-61-040-052-A ** ON A/C NOT FOR ALL

C. Deactivation of the Thrust Reverser for Ground Maintenance

WARNING: YOU MUST DEACTIVATE THE THRUST REVERSER BEFORE YOU DO WORK ON OR AROUND IT. IF YOU DO NOT, THE THRUST REVERSER CAN OPERATE ACCIDENTALLY AND CAUSE AN INJURY AND/OR DAMAGE.

(1) Do the deactivation of the thrust reverser system for ground maintenance (Ref. AMM TASK 78-30-00-040-805).

Subtask 77-21-61-010-055-A ** ON A/C NOT FOR ALL

D. Get Access
(1) Open the thrust reverser cowl-doors (Ref. AMM TASK 78-36-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
451AL, 452AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
461AL, 462AR.

4. Procedure
Subtask 77-21-61-020-051-A ** ON A/C NOT FOR ALL

A. Removal of the Exhaust Gas Temperature (EGT) (T5/T3) Wiring Harness (WC05)

Exhaust Gas Temperature (EGT) (T5/T3) Wiring Harness (WC05) ** ON A/C NOT FOR ALL

CAUTION: WIPE CLEAN ALL PARTS AND TOOLS AS NECESSARY TO REMOVE UNWANTED DEBRIS AND PREVENT DAMAGE TO THE ENGINE.

(1) Removal of the protection covers:

CAUTION: REMOVE THE PROTECTION COVERS FROM THE OPENINGS AS NECESSARY TO PREVENT ENGINE DAMAGE.

(a) Make sure that you remove all the necessary COVER - PROTECTION to prevent damage to the engine.
(2) Find the harness (WC05) (1) attached to the top side of the engine connected to the EGT temperature sensors and the EGT probes.
(3) Remove the harness (WC05) (1) from the engine as follows:
(a) Disconnect the self-locking connector (P43) from the wiring harness (WC05) receptacle (J43) with the PLIERS - JAWED, SOFT.
(b) Remove the nuts and disconnect the harness (WC05) (1) from the T3 probe.
(c) Remove the two clamps and the two bolts from the harness mounting bracket (WC05) (1).
(d) Remove the nuts and disconnect the harness (WC05) (1) from the two left and two right EGT T5 probes on the Turbine Exhaust Case (TEC).
(e) Start from the rear of the engine and carefully remove the harness (WC05) (1) from the 36 spring clips.
(f) Remove the harness (WC05) (1) from the engine.
(4) Installation of the protection covers:

CAUTION: INSTALL PROTECTION COVERS ON ALL THE OPENINGS IMMEDIATELY TO PREVENT DAMAGE TO THE ENGINE.

(a) Make sure that you install COVER - PROTECTION as necessary to prevent damage to the engine.

[Rev.10 from 2021] 2026.04.01 13:06:29 UTC