DOC AIRBUS | AMM A320FInstallation of the HJ10 Harness for SAC Engines [CFMB]
TASK 73-21-50-400-043-A
Installation of the HJ10 Harness for SAC Engines
1. Reason for the Job
This task is applicable for SAC Engines.
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Work Zones and Access Panels
D. Referenced Information
3. Job Set-up
Subtask 73-21-50-860-066-A ** ON A/C NOT FOR ALL
Subtask 73-21-50-420-071-A ** ON A/C NOT FOR ALL
Subtask 73-21-50-410-090-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 02:59:01 UTC
Installation of the HJ10 Harness for SAC Engines
1. Reason for the Job
This task is applicable for SAC Engines.
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | PLIERS - CONNECTOR, JAW, SOFT |
| No specific | AR | WARNING NOTICE(S) |
| No specific | Torque wrench: range to between 53 and 47 lbf.in (0.60 and 0.53 m.daN )  |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.CP2101) | graphite grease |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| FOR [1000EM1] (ENGINE-1) | |
| 437AL, 438AR, 451AL, 452AR | |
| FOR [1000EM2] (ENGINE-2) | |
| 447AL, 448AR, 461AL, 462AR | |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 71-13-00-010-040-B | Opening of the Fan Cowl Doors |
| TASK 71-13-00-410-040-B | Closing of the Fan Cowl Doors |
| TASK 73-29-00-710-040-B | Operational Test of the FADEC on the Ground (with Engine Motoring) |
| TASK 73-29-00-710-040-B-02 | Operational Test of the FADEC on the Ground (with Engine Non motoring) |
| TASK 78-30-00-081-041-B | Make the Thrust Reverser Serviceable after Maintenance |
| TASK 78-30-00-481-041-B | Make the Thrust Reverser Unserviceable for Maintenance |
| TASK 78-36-00-010-040-B | Opening of the Thrust Reverser Doors |
| TASK 78-36-00-410-040-B | Closing of the Thrust Reverser Doors |
HJ10 HarnessSubtask 73-21-50-860-066-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a WARNING NOTICE(S) is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a WARNING NOTICE(S) is in position to tell persons not to energize the FADEC 1(2).
Subtask 73-21-50-010-133-A ** ON A/C NOT FOR ALL (1) On the center pedestal, on the ENG panel 115VU, make sure that a WARNING NOTICE(S) is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a WARNING NOTICE(S) is in position to tell persons not to energize the FADEC 1(2).
B. Get Access
(1) Make sure that the fan cowl doors are open (Ref. AMM TASK 71-13-00-010-040):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(2) Make sure that the thrust reverser door are open (Ref. AMM TASK 78-36-00-010-040):
(a) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(b) FOR [1000EM2] (ENGINE-2)
461AL 462AR
Subtask 73-21-50-040-089-A ** ON A/C NOT FOR ALL 4. Procedure(1) Make sure that the fan cowl doors are open (Ref. AMM TASK 71-13-00-010-040):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(2) Make sure that the thrust reverser door are open (Ref. AMM TASK 78-36-00-010-040):
(a) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(b) FOR [1000EM2] (ENGINE-2)
461AL 462AR
Subtask 73-21-50-420-071-A ** ON A/C NOT FOR ALL
A. Installation of the HJ10 Harness
(2) Make sure that all the electrical connections are clean and in the correct condition.
(3) Install the HJ10 harness in position on the engine.
(4) Connect the HJ10 harness to the T12 sensor CH. B, the control alternator CH. B, the starter air valve CH. B, the N1 speed sensor CH. B and the ECU (receptacle J10). Use PLIERS - CONNECTOR, JAW, SOFT only if necessary.
(5) Make sure that the connectors are fully engaged and do not move.
(6) Lubricate the threads of the bolts with graphite grease (Material No.CP2101) .
(7) Install the parts which attach the HJ10 harness as follows:
(8) Make sure that the harness is not stressed.
(9) Engage the HJ10 harness in the flexible clamp (170), and attach it to the clamp (180) on bracket (190) on fan frame between flange E and flange F, at the 5:30 o'clock position, with cover plate (210) and bolts (200) (Detail K).
(10) Engage the HJ10 harness in the flexible clamp (250), and attach it on the bracket (240) on the right-hand side of the TGB with cover plate (220) and bolts (230) (Detail L).
(11) Engage the HJ10 harness in the clip (140) on bracket (130), on fan frame flange C, at the 5:15 o'clock position (Detail H).
(12) Engage the HJ10 harness in the clip (160) on bracket (150), on fan frame flange E at the 5:15 o'clock position under the AGB (Detail J).
(13) Engage the HJ10 harness in the clips (360), (380) on brackets (350), (370), on fan frame flange C, at the 4:30 and 3:45 o'clock positions (Details Q, R).
(14) TORQUE the bolts (10), (60), (70), (120), (200), (230), (260), (290), (320), (390), (420), (450), (490), (520), (550) to between 53 and 47 lbf.in (0.60 and 0.53 m.daN ).
Subtask 73-21-50-710-071-A ** ON A/C NOT FOR ALL 5. Close-upCAUTION:
CAREFULLY ALIGN THE CONNECTOR KEY WITH THE RECEPTACLE KEYWAY BEFORE YOU CONNECT THEM TO PREVENT DAMAGE TO THE CONNECTORS.
CAUTION:
DISTRIBUTE THE SLACK ALL ALONG THE CABLE. DO NOT LET THE CABLE SHEATH TOUCH THE ADJACENT COMPONENTS. DO NOT TWIST THE SHEATH BY MORE THAN 180 DEGREES.
(1) Remove the CAP-BLANKING from each electrical connector and receptacle.(2) Make sure that all the electrical connections are clean and in the correct condition.
(3) Install the HJ10 harness in position on the engine.
(4) Connect the HJ10 harness to the T12 sensor CH. B, the control alternator CH. B, the starter air valve CH. B, the N1 speed sensor CH. B and the ECU (receptacle J10). Use PLIERS - CONNECTOR, JAW, SOFT only if necessary.
(5) Make sure that the connectors are fully engaged and do not move.
(6) Lubricate the threads of the bolts with graphite grease (Material No.CP2101) .
(7) Install the parts which attach the HJ10 harness as follows:
| INSTALL | ON | NOTE |
|---|---|---|
| Clamp (30) Bolt (10) | Bracket (20) | On fan frame flange C at the 5 o'clock position (Detail D) |
| Clamp (50) Bolt (60) | Bracket (40) | On fan frame flange B at the 5 o'clock position (Detail E) |
| Clamp (80) Bolt (70) | Bracket (90) | On fan frame flange B at the 5:30 o'clock position (Detail F) |
| Clamp (110) Bolt (120) | Bracket (100) | On fan frame flange B at the 5:45 o'clock position (Detail G) |
| Clamp (270) Bolt (260) | Bracket (280) | On TGB right-hand side (Detail M) |
| Clamp (300) Bolt (290) | Bracket (310) | On fan frame flange G, at the 5:45 o'clock position (Detail N) |
| Clamp (330) Bolt (320) | Bracket (340) | On fan frame flange B, at the 3:30 o'clock position (Detail P) |
| Clamp (400) Bolt (390) | Bracket (410) | On fan frame flange C, at the 3:30 o'clock position (Detail S) |
| Clamp (440) Bolt (420) | Bracket (430) | On fan frame flange C, at the 3:30 o'clock position (Detail T) |
| Clamp (480) Bolt (450) | Bracket (460) and clamp (470) on HJ9 harness | On fan frame flange D, at the 3:30 o'clock position (Detail U) |
| Clamps (510) Bolts (490) | Brackets (500) (four locations) | On fan frame flange C, between the 1:30 and 3 o'clock positions (Detail V) |
| Clamp (540) Bolt (520) | Bracket (530) | On fan frame flange C, at the 1 o'clock position (Detail W) |
| Clamp (560) Bolt (550) | Bracket (570) | On fan frame flange B, at the 1 o'clock position (Detail X) |
(9) Engage the HJ10 harness in the flexible clamp (170), and attach it to the clamp (180) on bracket (190) on fan frame between flange E and flange F, at the 5:30 o'clock position, with cover plate (210) and bolts (200) (Detail K).
(10) Engage the HJ10 harness in the flexible clamp (250), and attach it on the bracket (240) on the right-hand side of the TGB with cover plate (220) and bolts (230) (Detail L).
(11) Engage the HJ10 harness in the clip (140) on bracket (130), on fan frame flange C, at the 5:15 o'clock position (Detail H).
(12) Engage the HJ10 harness in the clip (160) on bracket (150), on fan frame flange E at the 5:15 o'clock position under the AGB (Detail J).
(13) Engage the HJ10 harness in the clips (360), (380) on brackets (350), (370), on fan frame flange C, at the 4:30 and 3:45 o'clock positions (Details Q, R).
(14) TORQUE the bolts (10), (60), (70), (120), (200), (230), (260), (290), (320), (390), (420), (450), (490), (520), (550) to between 53 and 47 lbf.in (0.60 and 0.53 m.daN )
. Subtask 73-21-50-410-090-A ** ON A/C NOT FOR ALL
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the thrust reverser doors (Ref. AMM TASK 78-36-00-410-040):
(a) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(b) FOR [1000EM2] (ENGINE-2)
461AL 462AR
Subtask 73-21-50-440-080-A ** ON A/C NOT FOR ALL Subtask 73-21-50-410-108-A ** ON A/C NOT FOR ALL (1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the thrust reverser doors (Ref. AMM TASK 78-36-00-410-040):
(a) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(b) FOR [1000EM2] (ENGINE-2)
461AL 462AR