Removal of the Burner Pressure Sensor [PW11]

TASK 73-21-23-000-801-A
Removal of the Burner Pressure Sensor

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE AFTER SHUTDOWN. THE ENGINE CAN STAY HOT FOR A LONG TIME. IF YOU DO NOT OBEY THIS INSTRUCTION, INJURY CAN OCCUR.

ZONE: 400
FIN: 4085KS ** ON A/C NOT FOR ALL

1. Reason for the Job
Use this procedure to remove the burner pressure sensor.
For more information about the burner pressure sensor, refer to 73-00-00 ENGINE FUEL AND CONTROL-GENERAL-DESCRIPTION AND OPERATION.
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 1M(3 FT)
No specific	AR	COVER - PROTECTION
No specific	1	PLIERS - JAWED, SOFT

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
400	POWER PLANT, NACELLES AND PYLONS
FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL, 438AR, 451AL
FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL, 448AR, 461AL

C. Referenced Information

REFERENCE	DESIGNATION
TASK 71-00-00-860-832-A	Procedure to Prevent Engine Motoring and to Stop the Electrical Supply to the EEC
TASK 71-13-00-010-802-A	Opening of the Fan Cowl Doors
TASK 78-30-00-040-805-A	Deactivation of the Thrust Reverser System for Ground Maintenance
TASK 78-36-00-010-802-A	Opening of the Thrust Reverser Cowl-Doors
Burner Pressure Sensor

3. Job Set-up
Subtask 73-21-23-941-050-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) Do the procedure to prevent engine motoring and to stop the electrical supply to the Electronic Engine Control (EEC)
(Ref. AMM TASK 71-00-00-860-832)

Subtask 73-21-23-010-050-A ** ON A/C NOT FOR ALL

B. Get Access
(1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
437AL 438AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
447AL 448AR
(2) Put an ACCESS PLATFORM 1M(3 FT) in position.

Subtask 73-21-23-040-050-A ** ON A/C NOT FOR ALL

C. Deactivation of the Thrust Reverser for Maintenance

WARNING: YOU MUST DEACTIVATE THE THRUST REVERSER BEFORE YOU DO WORK ON OR AROUND IT. IF YOU DO NOT, THE THRUST REVERSER CAN OPERATE ACCIDENTALLY AND CAUSE AN INJURY AND/OR DAMAGE.

(1) Do the deactivation of the thrust reverser system for maintenance (Ref. AMM TASK 78-30-00-040-805).

Subtask 73-21-23-010-051-A ** ON A/C NOT FOR ALL

D. Get Access
(1) Open the left thrust-reverser cowl-doors (Ref. AMM TASK 78-36-00-010-802):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENG 1)
451AL
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENG 2)
461AL

4. Procedure

CAUTION: WIPE CLEAN ALL PARTS AND TOOLS AS NECESSARY TO REMOVE UNWANTED DEBRIS AND PREVENT DAMAGE TO THE ENGINE.

Subtask 73-21-23-020-050-A ** ON A/C NOT FOR ALL

A. Removal of the Burner Pressure Sensor
(1) Removal of the protection covers:

CAUTION: REMOVE THE PROTECTION COVERS FROM THE OPENINGS AS NECESSARY TO PREVENT ENGINE DAMAGE.

(a) Make sure that you remove all the necessary COVER - PROTECTION to prevent damage to the engine.
(2) Find the burner pressure sensor (1) attached to the bleed valve solenoid (AV170) bracket at the 11 o'clock position.
(3) Remove the sensor (1) from the solenoid (AV170) bracket as follows:
(a) Disconnect the wiring harness (W03) from the sensor receptacle (J39) with PLIERS - JAWED, SOFT.
(b) Disconnection of the sense tube:

CAUTION: USE A SECOND WRENCH TO HOLD THE MATING PARTS WHEN YOU LOOSEN OR TIGHTEN THE TUBE OR HOSE NUTS. IF YOU DO NOT OBEY THIS CAUTION, YOU CAN TWIST OR CAUSE DAMAGE TO THE TUBES OR HOSES.

1 Disconnect the sense tube (AS11) from the sensor (1).
(c) Remove the two bolts (4) that attach the sensor (1) to the bracket (3).
(d) Remove the sensor (1).
(e) Remove the three bolts (2) that attach the bracket (3) to the solenoid (AV170) bracket.
(f) Remove the bracket (3).
(4) Installation of the protection covers:

CAUTION: INSTALL PROTECTION COVERS ON ALL THE OPENINGS IMMEDIATELY TO PREVENT DAMAGE TO THE ENGINE.

(a) Make sure that you install COVER - PROTECTION as necessary to prevent damage to the engine.

[Rev.10 from 2021] 2026.04.01 03:02:54 UTC