Installation of the Turbine Rear Frame (TRF) Drain Tube [CFMI]

TASK 71-73-49-400-005-A
Installation of the Turbine Rear Frame (TRF) Drain Tube

FIN: 1000EM1 ** ON A/C NOT FOR ALL
FIN: 1000EM2 ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	COVER - PROTECTION
No specific	AR	WARNING NOTICE(S)
No specific	Torque wrench: range to between 25 and 20 lbf.in (0.28 and 0.23 m.daN )
No specific	Torque wrench: range to between 315 and 300 lbf.in (3.56 and 3.39 m.daN )

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL, 438AR, 451AL, 452AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR, 461AL, 462AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 71-13-00-010-040-A	Opening of the Fan Cowl Doors
TASK 71-13-00-410-040-A	Closing of the Fan Cowl Doors
TASK 78-30-00-081-041-A	Make the Thrust Reverser Serviceable after Maintenance
TASK 78-30-00-481-041-A	Make the Thrust Reverser Unserviceable for Maintenance
TASK 78-36-00-010-040-A	Opening of the Thrust Reverser Doors
TASK 78-36-00-410-040-A	Closing of the Thrust Reverser Doors
Turbine Rear Frame Drain Tube

3. Job Set-up
Subtask 71-73-49-860-079-C ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a WARNING NOTICE(S) is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) is off. Make sure that a WARNING NOTICE(S) is in position to tell persons not to energize the FADEC 1(2).

Subtask 71-73-49-010-119-C ** ON A/C NOT FOR ALL

B. Get Access
(1) Make sure that the fan cowl doors are open: (Ref. AMM TASK 71-13-00-010-040)
(2) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(3) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(4) Make sure that the thrust reverser doors are open: (Ref. AMM TASK 78-36-00-010-040)
(5) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(6) FOR [1000EM2] (ENGINE-2)
461AL 462AR

Subtask 71-73-49-040-055-C ** ON A/C NOT FOR ALL

C. Make sure that the thrust reverser is unserviceable (Ref. AMM TASK 78-30-00-481-041).

4. Procedure
Subtask 71-73-49-420-086-C ** ON A/C NOT FOR ALL

A. Installation of the Turbine Rear Frame (TRF) Drain Tube.
(1) Remove the COVER - PROTECTION from the tube and TRF drain nipple.
(2) Put the clamp (15) on the tube (20).
(3) Connect the tube (20) to the TRF drain nipple and tighten the coupling nut (25) by hand.
(4) Make sure that the TFR drain tube (20) has a clearance of approximately 0.08 in. (2.03 mm) to the exhaust nozzle.
(5) Make sure that the tube (20) is in the correct position .
(6) Attach the clamp (15) to the bracket at engine Sta. 258 with the bolt (5) and the nut (10).
(7) TORQUE the nut (10) to between 25 and 20 lbf.in (0.28 and 0.23 m.daN )

.
(8) TORQUE the tube coupling nut (25) to between 315 and 300 lbf.in (3.56 and 3.39 m.daN )

5. Close-up
Subtask 71-73-49-410-087-C ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the thrust-reverser cowl doors: (Ref. AMM TASK 78-36-00-410-040)
(3) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(4) FOR [1000EM2] (ENGINE-2)
461AL 462AR

Subtask 71-73-49-440-053-C ** ON A/C NOT FOR ALL

B. Make the thrust reverser serviceable (Ref. AMM TASK 78-30-00-081-041)

Subtask 71-73-49-410-088-C ** ON A/C NOT FOR ALL

C. Close Access
(1) Close the fan cowl doors (Ref. AMM TASK 71-13-00-410-040):
(2) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(3) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(4) Remove the WARNING NOTICE(S).

[Rev.10 from 2021] 2026.04.01 02:24:18 UTC