Detailed Inspection of Pylon to Wing Forward Attachments, LH/RH

TASK 54-51-00-220-818-A
Detailed Inspection of Pylon to Wing Forward Attachments, LH/RH

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE AFTER SHUTDOWN. THE ENGINE CAN STAY HOT FOR A LONG TIME. IF YOU DO NOT OBEY THIS INSTRUCTION, INJURY CAN OCCUR.

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

CAUTION: DO NOT APPLY TEMPORARY PROTECTION SYSTEM (TPS) ON THE INSPECTION AREA. IF YOU APPLY TPS ON THE INSPECTION AREA, YOU CAN CAUSE DAMAGE TO THE AIRCRAFT.

ZONE: 410
ZONE: 420
ZONE: 470
ZONE: 480
FIN: 4020KM1
FIN: 4020KM2

1. Reason for the Job
Refer to the MPD TASK: 545318-01
DETAILED INSPECTION OF PYLON TO WING FORWARD ATTACHMENTS, LH/RH.
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
No specific	AR	WARNING NOTICE(S)

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.14SBA1)	Textile-Lint free Cotton -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
410	ENG 1 PYLON BOX AND FORWARD FAIRING
420	ENG 2 PYLON BOX AND FORWARD FAIRING
470	ENGINE 1 AFT PYLON
480	ENGINE 2 AFT PYLON
413ET, 423ET, 471AL, 472AR, 481AL, 482AR

D. Referenced Information

REFERENCE	DESIGNATION
TASK 51-78-00-916-001-A	Application of Temporary Protection System (TPS)
TASK 54-53-11-000-806-A	Removal of the Pylon-to-Wing Access Panels and Doors
TASK 54-53-11-400-806-A	Installation of the Pylon-to-Wing Access Panels and Doors
TASK 78-30-00-040-809-A	Deactivation of the Thrust Reverser System for Ground Maintenance
TASK 78-30-00-440-809-A	Reactivation of the Thrust Reverser System after Ground Maintenance
SRM 511100	(for corrective action)
SRM 512200	(for corrective action)
Pylon-to-Wing Forward Attachments

3. Job Set-up
Subtask 54-51-00-941-113-A

A. Safety Precautions
(1) On the center pedestal, on ENG panel 115VU:
(a) Make sure that the ENG/MODE selector switch is in the NORM position.
(b) Make sure that the ENG/MASTER 1(2) control switch was in the OFF position not less than five minutes before you do this procedure.
(c) Put a WARNING NOTICE(S) in position to tell persons not to operate the ENG/MODE selector switch and the ENG/MASTER 1(2) control switch.
(2) On the ENG section of maintenance panel 50VU:
(a) Make sure that the ON legend of the FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) in position to tell persons not to energize FADEC 1(2).

Subtask 54-51-00-040-109-A

B. Deactivation of the Thrust Reverser

WARNING: MAKE SURE THAT THE THRUST REVERSER IS LOCKED. IF NOT, THE THRUST REVERSER CAN OPERATE ACCIDENTALLY AND CAUSE INJURY TO PERSONNEL AND/OR DAMAGE TO THE REVERSER.

(1) Make the thrust reverser unserviceable for maintenance (Ref. AMM TASK 78-30-00-040-809).

Subtask 54-51-00-010-118-A

C. Get Access
(1) Put an ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position:
(a) For the left pylon, in zones 410 and 470
(b) For the right pylon, in zones 420 and 480.
(2) Remove the pylon-to-wing access panels (Ref. AMM TASK 54-53-11-000-806):
(a) For the left pylon: 413ET 471AL, 472AR
(b) For the right pylon: 423ET 481AL, 482AR.

Subtask 54-51-00-110-111-A

D. Preparation of the Inspection Area
(1) Make sure that the inspection area is sufficiently clean to do a satisfactory inspection of the area.
(2) If it is not sufficiently clean, clean the inspection area with Non Aqueous Cleaner-General - - (Material No.08BAA9) and Textile-Lint free Cotton - (Material No.14SBA1) .
(3) Make sure that there is no Temporary Protection System (TPS) layer and if there is a TPS layer, remove it (Ref. AMM TASK 51-78-00-916-001).

4. Procedure
Subtask 54-51-00-220-103-A

A. Inspection

Pylon-to-Wing Forward Attachments

(1) Do a detailed inspection of the pylon-to-wing forward attachments. Do this inspection on the left and right sides.
(2) Make sure that there is no:
(a) Corrosion damage:

If you find corrosion damage, refer to Structural Repair Manual SRM 512200 for types of corrosion, inspection, removal and corrosion protection.

(b) Other damage (scratches, cracks, gouges, dents, creases):

If you find this type of damage, refer to Structural Repair Manual SRM 511100 for damage classification and corrective action.

5. Close-up
Subtask 54-51-00-410-126-A

A. Close Access
(1) Install the pylon-to-wing access panels (Ref. AMM TASK 54-53-11-400-806):
(a) For the left pylon: 413ET 471AL, 472AR
(b) For the right pylon: 423ET 481AL, 482AR.

Subtask 54-51-00-440-108-A

B. Reactivation of the Thrust Reverser
(1) Make the thrust reverser serviceable after maintenance (Ref. AMM TASK 78-30-00-440-809).

Subtask 54-51-00-942-083-A

C. Aircraft Maintenance Configuration
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the access platform(s).
(3) Remove the WARNING NOTICE(S).

[Rev.10 from 2021] 2026.04.01 02:00:14 UTC