Installation of the Integrally-Lighted Identification Plate

TASK 33-13-41-400-001-A
Installation of the Integrally-Lighted Identification Plate

ZONE: 210
ZONE: 211
ZONE: 212
FIN: 18LF
FIN: 19LF
FIN: 20LF
FIN: 21LF
FIN: 22LF
FIN: 23LF
FIN: 24LF
FIN: 25LF
FIN: 26LF
FIN: 35LF
FIN: 36LF
FIN: 51LF

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
210	CKPT,FWD COMPT BHD TO FLT COMPT BULKHEAD
211	COCKPIT
212	COCKPIT

B. Referenced Information

REFERENCE	DESIGNATION
TASK 27-41-41-400-001-A	Installation of the Control Mechanism-Pitch Trim
TASK 27-51-43-400-002-A	Installation of the Lighted Plate
TASK 33-13-00-710-001-A	Operational Test of the Instrument and Panel Integral-Lighting
TASK 76-11-41-400-040-A	Installation of the Throttle Control Lever Assembly
TASK 76-11-41-400-041-A	Installation of the Throttle Control Lever Assembly
TASK 76-11-41-400-042-A	Installation of the Throttle Control Lever Assembly
TASK 76-11-41-400-802-A	Installation of the Throttle Control Lever Assembly
ESPM 2045210
AIPC 76-12-08-
Integrally-Lighted Identification Plate

3. Job Set-up
Subtask 33-13-41-865-051-A

A. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
122VU	LIGHTING/INSTL LT/MAIN INST/PNL AND/PED	4LF	Y04

4. Procedure
Subtask 33-13-41-420-054-B ** ON A/C NOT FOR ALL

A. Installation of the Integrally-Lighted Identification Plate (21LF)
(1) Install the integrally-lighted identification plate of the throttle control-lever assembly (Ref. AMM TASK 76-11-41-400-040).

Subtask 33-13-41-420-054-C ** ON A/C NOT FOR ALL

A. Installation of the Integrally-Lighted Identification Plate (21LF)
(1) Install the integrally-lighted identification plate of the throttle control-lever assembly (Ref. AMM TASK 76-11-41-400-041).

Subtask 33-13-41-420-054-D ** ON A/C NOT FOR ALL

A. Installation of the Integrally-Lighted Identification Plate (21LF)
(1) Install the integrally-lighted identification plate of the throttle control-lever assembly (Ref. AMM TASK 76-11-41-400-042).

Subtask 33-13-41-420-054-F ** ON A/C NOT FOR ALL

A. Installation of the Integrally-Lighted Identification Plate (21LF)
(1) Install the integrally-lighted identification plate of the throttle control-lever assembly (Ref. AMM TASK 76-11-41-400-802).

Subtask 33-13-41-420-050-A

B. Installation of the Integrally-Lighted Identification Plate (19LF and 20LF)

Integrally-Lighted Identification Plate

(1) Put the integrally-lighted identification plates (36) and (38).
(2) Install the screws (35) and (37).
(3) Install the indicators (34) and the wheels (33) (Ref. AMM TASK 27-41-41-400-001).

Subtask 33-13-41-420-055-A

C. Installation of the Integrally-Lighted Identification Plate (18LF)
(1) Put the integrally-lighted identification plate (2) in position on SWITCHING panel 8VU (4).
(2) Install the four screws (1).
(3) Tighten the four screws (1).
(4) Tighten the four quarter-turn fasteners (3).

Subtask 33-13-41-420-056-A

D. Installation of the Integrally-Lighted Identification Plates (23LF and 24LF)
(1) Put the integrally-lighted identification plates (30) and (6) in position on FLOOD LT panel 112VU (32) and FLOOD LT/INTEG LT panel 111VU (8).
(2) Install the two screws (29) and (5).
(3) Tighten the two screws (29) and (5).
(4) Tighten the two quarter-turn fasteners (31) and (7).

Subtask 33-13-41-420-057-A

E. Installation of the Integrally-Lighted Identification Plate (26LF)
(1) Pull the disassembled ENG/MASTER 1 and 2 control switches (3KC and 2KC) through the integrally-lighted identification plate (26).
(2) Put the integrally-lighted identification plate (26) in position on ENG panel 115VU (28).
(3) Install the three screws (25).
(4) Tighten the three screws (25).
(5) Tighten the four quarter-turn fasteners (27).
(6) Install the washers, the nuts and the knobs of the ENG/MASTER 1 and 2 control switches (3KC and 2KC) AIPC 76-12-08- ESPM 2045210.

Subtask 33-13-41-420-058-A

F. Installation of the Integrally-Lighted Identification Plate (22LF)
(1) Put the integrally-lighted identification plate (10) in position on RUD TRIM/PARKING BRK panel 110VU (11).
(2) Install the four screws (9).
(3) Tighten the four screws (9).
(4) Tighten the four quarter-turn fasteners (12).

Subtask 33-13-41-420-059-A

G. Installation of the Integrally-Lighted Identification Plates (35LF and 36LF)
(1) Put the integrally-lighted identification plates (14) in position on the GEAR panel (16).
(2) Install the four screws (13) and (15).
(3) Tighten the four screws (13) and (15).

Subtask 33-13-41-420-060-A

H. Installation of the Integrally-Lighted Identification Plate (25LF)
(1) Install the integrally-lighted identification plate (Ref. AMM TASK 27-51-43-400-002).

Subtask 33-13-41-420-061-A

I. Installation of the Integrally-Lighted Identification Plate (50LF), if Installed
(1) Put the integrally-lighted identification plate (18) in position on VIP COM panel 113VU (20).
(2) Install the three screws (17).
(3) Tighten the three screws (17).
(4) Tighten the two quarter-turn fasteners (19).

Subtask 33-13-41-420-062-A

J. Installation of the Integrally-Lighted Identification Plate (51LF), if Installed
(1) Put the integrally-lighted identification plate (22) in position on COCKPIT DOOR panel 119VU (24).
(2) Install the three screws (21).
(3) Tighten the three screws (21).
(4) Tighten the two quarter-turn fasteners (23).

Subtask 33-13-41-865-052-A

K. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
122VU	LIGHTING/INSTL LT/MAIN INST/PNL AND/PED	4LF	Y04

Subtask 33-13-41-710-050-A

L. Do the operational test (Ref. AMM TASK 33-13-00-710-001).

5. Close-up
Subtask 33-13-41-942-050-A

A. Make sure that the work area is clean and clear of tools and other items.

[Rev.10 from 2021] 2026.04.01 00:52:50 UTC