Removal of the Blue Leakage-Measurement Solenoid-Valve

TASK 29-19-51-000-002-A
Removal of the Blue Leakage-Measurement Solenoid-Valve

WARNING: MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS SURFACES ARE CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.

WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.

1. Reason for the Job
This task is applicable for Aircraft with the Blue High-Pressure Manifold P/N D29070173 series.
This task is not applicable for Aircraft with the Blue High-Pressure Manifold P/N 1554A9900 series.
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	2	CAP - BLANKING
No specific	1	CONTAINER 1 L (1/4 USGAL)
No specific	AR	PLUG - BLANKING
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	2	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
195BB

C. Referenced Information

REFERENCE	DESIGNATION
TASK 20-23-21-911-001-A	Removal/Installation of the Bobbins from their Housings and Installation of O-rings, Square Seals, and Back-up Rings on the Bobbins
TASK 29-00-00-864-001-A	Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action
TASK 29-14-00-614-001-A	Depressurization of the Hydraulic Reservoirs
Leakage Measurement Solenoid Valve

3. Job Set-up
Subtask 29-19-51-865-053-A

A. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C ALL
121VU	HYDRAULIC/SOL VALVES/G/Y/B/LEAK/TST	1881GP	N35

Subtask 29-19-51-010-051-A

B. Open the access panel 195BB.

Subtask 29-19-51-860-054-A

C. Aircraft Maintenance Configuration

WARNING: OBEY THE HYDRAULIC SAFETY PROCEDURES.

(1) Obey the hydraulic safety procedures (Ref. AMM TASK 29-00-00-864-001).
(2) Make sure that the Blue hydraulic system is depressurized and put it in the maintenance configuration.
(Ref. AMM TASK 29-00-00-864-001).
(3) Depressurize the reservoir of the Blue hydraulic system.
(Ref. AMM TASK 29-14-00-614-001).

Subtask 29-19-51-941-051-A

D. Safety Precautions
(1) Put the WARNING NOTICE(S) in position to tell persons not to pressurize the Blue hydraulic system:

In the cockpit on the hydraulic section 40VU of the overhead panel
On the ground service panel of the Blue hydraulic system.

(2) Put the CONTAINER 1 L (1/4 USGAL) in position below the leakage-measurement solenoid valve (referred to as solenoid valve) to collect the hydraulic fluid.

4. Procedure
Subtask 29-19-51-020-051-A

A. Removal of the Solenoid Valve 2150GP
(1) Disconnect the electrical connector (1).
(2) Put a CAP - BLANKING on the disconnected electrical connector (1) and on the receptacle.

CAUTION: MAKE SURE THAT THE ELECTRICAL CONNECTOR(S) IS(ARE) DISCONNECTED BEFORE YOU DISCONNECT THE BONDING STRAP(S).

(3) Remove the nut (2), the washer (3), the bolt (4) and the bonding strap (5) from the solenoid valve (6).
(4) Hold the solenoid valve (6) and remove the bolts (7) and the washers (8).
(5) Remove the solenoid valve (6).
(6) Remove the bobbins (10) and (11) (Ref. AMM TASK 20-23-21-911-001).
(7) Install a PLUG - BLANKING in the open ports of the manifold (13).
(8) Remove and discard the square-section seals (14) and (19), the O-rings (12) and (9) and the back-up rings (17), (18), (15) and (16).

[Rev.10 from 2021] 2026.04.01 00:25:40 UTC