Removal of the Air Relief Valve of the Green Hydraulic System

TASK 29-14-17-000-001-A
Removal of the Air Relief Valve of the Green Hydraulic System

WARNING: OBEY THE HYDRAULIC SAFETY PROCEDURES.

WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.

FIN: 1005GM

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
No specific	AR	PLUG - BLANKING
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	2	WARNING NOTICE(S)

B. Referenced Information

REFERENCE	DESIGNATION
TASK 29-00-00-864-001-A	Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action
TASK 29-00-00-910-002-A	Safety Procedures of the Hydraulic System
TASK 29-14-00-614-001-A	Depressurization of the Hydraulic Reservoirs
TASK 32-12-00-010-001-A	Open the Main Gear Doors for Access
Pressure Relief Valve

3. Job Set-up
Subtask 29-14-17-865-050-A

A. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	HYDRAULIC/G HYD/PUMP ENG1/CTL	1701GK	H12
** ON A/C NOT FOR ALL
121VU	HYDRAULIC/G HYD/PUMP ENG1/CTL	1701GK	R35
** ON A/C NOT FOR ALL
121VU	HYDRAULIC/G HYD/PUMP ENG1/MONG	1702GK	R34
** ON A/C ALL
121VU	HYDRAULIC/LOW/LVL/IND	1832GQ	N32
121VU	HYDRAULIC/HYD/QTY/IND	1831GQ	P35
** ON A/C NOT FOR ALL
121VU	HYDRAULIC/G HYD/PUMP ENG1/MONG	1702GK	R33

Subtask 29-14-17-860-050-A

B. Aircraft Maintenance Configuration
(1) Obey the hydraulic safety procedures (Ref. AMM TASK 29-00-00-910-002).
(2) Put the WARNING NOTICE(S) in position to tell persons not to pressurize the hydraulic system:

In the cockpit on the hydraulic section 40VU of the overhead panel,
On the ground service panel of the Green hydraulic system.

(3) Make sure that the Green hydraulic system is depressurized and put it in the maintenance configuration.
(Ref. AMM TASK 29-00-00-864-001).
(4) Depressurize the reservoir of the Green hydraulic system (Ref. AMM TASK 29-14-00-614-001).
(5) Open the right hand door of the main gear (Ref. AMM TASK 32-12-00-010-001).
(6) Put an ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position.

4. Procedure
Subtask 29-14-17-020-050-A

A. Removal of the Air Relief Valve

CAUTION: USE A SECOND WRENCH TO APPLY COUNTERTORQUE TO THE UNION WHEN YOU DISCONNECT/CONNECT HYDRAULIC LINES ON UNIONS. IF YOU DO NOT USE THE SECOND WRENCH, THERE IS A RISK THAT YOU WILL LOOSEN OR TIGHTEN THE UNION TOO MUCH.

(1) Cut, remove and discard the lockwire.
(2) Hold the air relief valve (2) and disconnect the union nut (1).
(3) Remove the air relief valve (2) and discard the O-ring (3).
(4) Install a PLUG - BLANKING on the open connections.

[Rev.10 from 2021] 2026.04.01 08:09:22 UTC