Removal of the Accumulator-Gas Charging Valve

TASK 29-11-22-000-001-A
Removal of the Accumulator-Gas Charging Valve

WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.

ZONE: 147
FIN: 1071GM

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
No specific	1	CAP - BLANKING
No specific	1	PLUG - BLANKING
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	1	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
147	MAIN GEAR WELL AND HYDRAULIC COMPARTMENT

C. Referenced Information

REFERENCE	DESIGNATION
TASK 29-00-00-864-001-A	Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action
TASK 29-14-00-614-001-A	Depressurization of the Hydraulic Reservoirs
TASK 29-23-00-860-001-A	Disconnection of the Isolation Coupling of the Power Transfer Unit (PTU)
TASK 32-12-00-010-001-A	Open the Main Gear Doors for Access
Gas Charging Valve

3. Job Set-up
Subtask 29-11-22-865-050-A

A. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	HYDRAULIC/G HYD/PUMP ENG1/CTL	1701GK	H12
** ON A/C NOT FOR ALL
121VU	HYDRAULIC/G HYD/PUMP ENG1/CTL	1701GK	R35
** ON A/C NOT FOR ALL
121VU	HYDRAULIC/G HYD/PUMP ENG1/MONG	1702GK	R34
** ON A/C ALL
121VU	HYDRAULIC/SOL VALVES/G/Y/B/LEAK/TST	1881GP	N35
** ON A/C NOT FOR ALL
121VU	HYDRAULIC/G HYD/PUMP ENG1/MONG	1702GK	R33

Subtask 29-11-22-860-050-A

B. Aircraft Maintenance Configuration
(1) Put the WARNING NOTICE(S) in position to tell persons not to pressurize the Green hydraulic system:

In the cockpit on the hydraulic section 40VU of the overhead panel
On the ground service panel of the Green hydraulic system.

(2) Make sure that the Green hydraulic system is depressurized and put it in the maintenance configuration.
(Ref. AMM TASK 29-00-00-864-001).
(3) Depressurize the reservoir of the Green hydraulic system (Ref. AMM TASK 29-14-00-614-001).
(4) Open the left main door of the main gear (Ref. AMM TASK 32-12-00-010-001).
(5) Put an ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position at the left door of the main gear.
(6) Disconnect the isolation coupling of the Power Transfer Unit (PTU) (Ref. AMM TASK 29-23-00-860-001).

4. Procedure
Subtask 29-11-22-614-050-A

A. Depressurize the Power Accumulator (1070GM) (1)
(1) Remove the endcap (6) from the charging-valve (4).
(2) Turn the nut (5) carefully to the OPEN position and release the nitrogen pressure.

Subtask 29-11-22-020-050-A

B. Removal of the Gas Charging-Valve (1071GM)
(1) Cut, remove and discard the lockwire from the gas charging valve (4).
(2) Remove the gas charging-valve (4).
(3) Install the PLUG - BLANKING in the adapter (2).
(4) Install the CAP - BLANKING on the gas charging-valve (4).

[Rev.10 from 2021] 2026.04.01 07:53:43 UTC