Installation of the Roller Assembly

TASK 25-52-26-400-002-A
Installation of the Roller Assembly

WARNING: DO NOT GET THE FLUID ON YOUR SKIN OR IN YOUR EYES. IF YOU DO:

FLUSH IT AWAY WITH CLEAN WATER
GET MEDICAL AID.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

CAUTION: USE ONLY THE SPECIFIED MATERIALS AND OBEY THE INSTRUCTIONS FROM THE MATERIAL MANUFACTURERS. OTHER MATERIALS CAN CAUSE DAMAGE TO THE SURFACE PROTECTION OF THE COMPONENTS AND THE RELATED AREA.

ZONE: 130
ZONE: 150

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 2M (6 FT)

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.03GBB1)	Synthetic Oil base Grease-General Purpose Clay Thickened -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
130	FWD CARGO COMPT AFT BULKHEAD OF AVNCS COMPT TO FWD PRESSURE BULKHEAD OF WING CENTER BOX
150	AFT CARGO COMPARTMENT FWD PRESS BULKHEAD TO AFT BULKHEAD OF AFT CARGO COMPARTMENT

D. Referenced Information

REFERENCE	DESIGNATION
TASK 24-42-00-861-001-A	Energize the Ground Service Network from the External Power
TASK 24-42-00-862-001-A	De-energize the Ground Service Network Supplied from the External Power
TASK 25-52-26-400-001-A	Installation of the Power Drive Unit
TASK 52-30-00-860-001-A	Open the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump
TASK 52-30-00-860-002-A	Close the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump
Roller Assy

3. Job Set-up
Subtask 25-52-26-860-050-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Make sure that the ground service network is energized
(Ref. AMM TASK 24-42-00-861-001).
(2) Make sure that the forward and/or aft cargo-compartment door is opened (Ref. AMM TASK 52-30-00-860-001).
(3) Make sure that the ACCESS PLATFORM 2M (6 FT) is in position at the opening of the applicable cargo-compartment door.
(4) Make sure that the warning notice is in position at the applicable control panel of the cargo loading system.
(5) Make sure that the light switch of the forward and/or aft cargo-compartment is in the "ON" position.

Subtask 25-52-26-865-066-A ** ON A/C NOT FOR ALL

B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
2000VU	SEMI AUTO CLS-FWD	3MY	E08
2000VU	SEMI AUTO CLS-FWD	2MY	E06
2001VU	SEMI AUTO CLS-AFT	103MY	D08
2001VU	SEMI AUTO CLS-AFT	102MY	D06

4. Procedure
Subtask 25-52-26-910-051-A ** ON A/C NOT FOR ALL

A. Preparation for Installation
(1) Clean the component interfaces and the adjacent area.
(2) Do an inspection of the component interfaces and the adjacent area.
(3) Apply Synthetic Oil base Grease-General Purpose Clay Thickened - (Material No.03GBB1) to the roller shaft (6).

Subtask 25-52-26-420-051-B ** ON A/C NOT FOR ALL

B. Installation of the Roller Assembly:
(1) Put the roller assembly (1) in its correct installation position in the power drive unit (7).
(2) Install the roller shaft (6) in the power drive unit (7) and the roller assembly (1).
(3) Install the retained shims (5) on the roller shaft (6).
(4) Install the stop disc (4).
(5) Safety the roller shaft (6) with the retaining ring (3).

5. Close-up
Subtask 25-52-26-410-051-A ** ON A/C NOT FOR ALL

A. Install the related power drive unit (Ref. AMM TASK 25-52-26-400-001).

Subtask 25-52-26-865-067-A ** ON A/C NOT FOR ALL

B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
2000VU	SEMI AUTO CLS-FWD	3MY	E08
2000VU	SEMI AUTO CLS-FWD	2MY	E06
2001VU	SEMI AUTO CLS-AFT	103MY	D08
2001VU	SEMI AUTO CLS-AFT	102MY	D06

Subtask 25-52-26-410-052-A ** ON A/C NOT FOR ALL

C. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the WARNING NOTICE(S).
(3) Close the forward and/or aft cargo-compartment door (Ref. AMM TASK 52-30-00-860-002).
(4) Set the light switch to off.
(5) Remove the access platform(s).
(6) De-energize the ground service network
(Ref. AMM TASK 24-42-00-862-001).

[Rev.10 from 2021] 2026.04.01 06:23:10 UTC