Maintenance of the Hot-Plate (if installed)
TASK 25-35-00-910-002-A
Maintenance of the Hot-Plate (if installed)
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Consumable Materials
B. Referenced Information
3. Job Set-up
Subtask 25-35-00-860-069-A ** ON A/C NOT FOR ALL
Subtask 25-35-00-160-058-A ** ON A/C NOT FOR ALL
(2) Rinse the surface with clean warm water and dry it fully with a lint-free cotton cloth Textile-Lint free Cotton - (Material No.14SBA1) .
5. Close-up
Subtask 25-35-00-860-070-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.03.31 23:34:07 UTC
Maintenance of the Hot-Plate (if installed)
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Consumable Materials
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.14FAB1) | Abrasive-- Scotch Brite Pads - |
| (Material No.14SBA1) | Textile-Lint free Cotton - |
| No specific | clean warm water |
| No specific | mild detergent solution |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-41-00-862-002-A | De-energize the Aircraft Electrical Circuits Supplied from the External Power |
| TASK 24-41-00-862-002-A-01 | De-energize the Aircraft Electrical Circuits Supplied from the APU |
| TASK 24-41-00-862-002-A-02 | De-energize the Aircraft Electrical Circuits Supplied from the Engine 1(2) |
| TASK 24-42-00-861-001-A | Energize the Ground Service Network from the External Power |
Subtask 25-35-00-860-069-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) Make sure that the ground service network is energized (Ref. AMM TASK 24-42-00-861-001).
(2) At the related galley on the Galley Control Panel
(a) Make sure that the related circuit breaker(s) of the hot-plate is(are) open, safetied and tagged.
4. Procedure(1) Make sure that the ground service network is energized (Ref. AMM TASK 24-42-00-861-001).
(2) At the related galley on the Galley Control Panel
(a) Make sure that the related circuit breaker(s) of the hot-plate is(are) open, safetied and tagged.
Subtask 25-35-00-160-058-A ** ON A/C NOT FOR ALL
WARNING:
DO NOT TOUCH THE UNIT UNTIL IT IS SUFFICIENTLY COOL TO PREVENT BURNS WHEN YOU DO THE MAINTENANCE TASK(S).
A. Clean the Hot-Plate NOTE: Make sure that the water and equipment you use for this procedure is clean and without particles that can damage the surfaces.
(1) Clean the surface of the plate with a scotch brite pad Abrasive-- Scotch Brite Pads - (Material No.14FAB1) and a mild detergent solution. (2) Rinse the surface with clean warm water and dry it fully with a lint-free cotton cloth Textile-Lint free Cotton - (Material No.14SBA1) .
Subtask 25-35-00-860-070-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) Clean the component interfaces and the adjacent area.
(2) Make sure that the work area is clean and clear of tools and other items.
(3) De-energize the ground service network
(Ref. AMM TASK 24-41-00-862-002).
(1) Clean the component interfaces and the adjacent area.
(2) Make sure that the work area is clean and clear of tools and other items.
(3) De-energize the ground service network
(Ref. AMM TASK 24-41-00-862-002).