DOC AIRBUS | AMM A320FInstallation of the Textile Floor Covering of the Cockpit (Carpet)
TASK 25-13-44-400-001-A
Installation of the Textile Floor Covering of the Cockpit (Carpet)
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Work Zones and Access Panels
D. Referenced Information
3. Job Set-up
Subtask 25-13-44-860-050-A
Subtask 25-13-44-420-050-A ** ON A/C NOT FOR ALL
Subtask 25-13-44-860-051-A
[Rev.10 from 2021]
2026.03.31 23:29:17 UTC
Installation of the Textile Floor Covering of the Cockpit (Carpet)
WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
ZONE: 210
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | ROLLER - RUBBER |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.05PCB2) | Double Sided Adhesive Tape-Carpet Bonding - - |
| (Material No.08BAA9) | Non Aqueous Cleaner-General - - |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 210 | CKPT,FWD COMPT BHD TO FLT COMPT BULKHEAD |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-42-00-861-001-A | Energize the Ground Service Network from the External Power |
| TASK 24-42-00-862-001-A | De-energize the Ground Service Network Supplied from the External Power |
| TASK 25-11-41-000-001-A | Removal of the Third Occupant Seat |
| TASK 25-11-41-400-001-A | Installation of the Third Occupant Seat |
| TASK 25-11-51-400-001-A | Installation of the CAPT/F/O Seat |
Textile Floor CoveringSubtask 25-13-44-860-050-A
A. Aircraft Maintenance Configuration
(1) Make sure that the ground service network is energized
(Ref. AMM TASK 24-42-00-861-001).
(2) Make sure that the Third Occupant seat is removed (Ref. AMM TASK 25-11-41-000-001).
(3) Make sure that the four case stops are removed.
4. Procedure(1) Make sure that the ground service network is energized
(Ref. AMM TASK 24-42-00-861-001).
(2) Make sure that the Third Occupant seat is removed (Ref. AMM TASK 25-11-41-000-001).
(3) Make sure that the four case stops are removed.
Subtask 25-13-44-420-050-A ** ON A/C NOT FOR ALL
A. Installation of the Textile Floor Covering
(2) Clean the floor area with Non Aqueous Cleaner-General - - (Material No.08BAA9) .
(3) Put the Double Sided Adhesive Tape-Carpet Bonding - - (Material No.05PCB2) (2) on the floor area.
(4) Apply pressure on the adhesive tapes with the ROLLER - RUBBER.
(5) Carefully put the floor covering (1) in position.
(6) Make sure that the installation is correct around the seat bottom.
(7) Apply pressure on the floor covering to put it in position.
(8) Make sure that the floor covering does not cause a blockage of the holes for the attachment of the seats.
(9) Install the grid (3).
(10) Install the cover strip (4).
(11) Install the 12 screws (5).
Subtask 25-13-44-420-050-B ** ON A/C NOT FOR ALL CAUTION:
DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF CARBONFIBER REINFORCED PLASTIC.
(1) Clean the component interfaces and the adjacent area.(2) Clean the floor area with Non Aqueous Cleaner-General - - (Material No.08BAA9) .
(3) Put the Double Sided Adhesive Tape-Carpet Bonding - - (Material No.05PCB2) (2) on the floor area.
(4) Apply pressure on the adhesive tapes with the ROLLER - RUBBER.
(5) Carefully put the floor covering (1) in position.
(6) Make sure that the installation is correct around the seat bottom.
(7) Apply pressure on the floor covering to put it in position.
(8) Make sure that the floor covering does not cause a blockage of the holes for the attachment of the seats.
(9) Install the grid (3).
(10) Install the cover strip (4).
(11) Install the 12 screws (5).
A. Installation of the Textile Floor Covering
(2) Clean the floor area with Non Aqueous Cleaner-General - - (Material No.08BAA9) .
(3) Put the Double Sided Adhesive Tape-Carpet Bonding - - (Material No.05PCB2) (4) on the floor area.
(4) With a ROLLER - RUBBER, apply pressure on the double sided adhesive tape (4).
(5) Carefully put the textile floor covering (1) in position.
(6) Make sure that the installation is correct around the seat bottom.
(7) Apply pressure on the textile floor covering (1) to put it in position.
(8) Make sure that the textile floor covering (1) does not cause a blockage of the holes for the attachment of the seats.
(9) Install the cover strip (3).
(10) Install the screws (2).
Subtask 25-13-44-420-053-A CAUTION:
DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF CARBONFIBER REINFORCED PLASTIC.
(1) Clean the component interfaces and the adjacent area.(2) Clean the floor area with Non Aqueous Cleaner-General - - (Material No.08BAA9) .
(3) Put the Double Sided Adhesive Tape-Carpet Bonding - - (Material No.05PCB2) (4) on the floor area.
(4) With a ROLLER - RUBBER, apply pressure on the double sided adhesive tape (4).
(5) Carefully put the textile floor covering (1) in position.
(6) Make sure that the installation is correct around the seat bottom.
(7) Apply pressure on the textile floor covering (1) to put it in position.
(8) Make sure that the textile floor covering (1) does not cause a blockage of the holes for the attachment of the seats.
(9) Install the cover strip (3).
(10) Install the screws (2).
B. Installation of the Straps
(1) Put the two straps (5) in position.
(2) Install the angle fitting (4) and the four stirrups (3).
(3) Install the 12 washers (2) and screws (1).
Subtask 25-13-44-420-052-A (1) Put the two straps (5) in position.
(2) Install the angle fitting (4) and the four stirrups (3).
(3) Install the 12 washers (2) and screws (1).
C. Installation of the Case Stops
(1) Install the four case stops (3).
(2) Install the eight washers (2) and screws (1).
Subtask 25-13-44-420-051-A (1) Install the four case stops (3).
(2) Install the eight washers (2) and screws (1).
D. Installation of the Seats
(1) Install the Third Occupant seat (Ref. AMM TASK 25-11-41-400-001).
(2) If removed, install the Captain and the First Officer seats (Ref. AMM TASK 25-11-51-400-001).
5. Close-up(1) Install the Third Occupant seat (Ref. AMM TASK 25-11-41-400-001).
(2) If removed, install the Captain and the First Officer seats (Ref. AMM TASK 25-11-51-400-001).
Subtask 25-13-44-860-051-A
A. Aircraft Maintenance Configuration
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Put the aircraft back to the serviceable condition.
Subtask 25-13-44-862-050-A (1) Make sure that the work area is clean and clear of tools and other items.
(2) Put the aircraft back to the serviceable condition.