DOC AIRBUS | AMM A320FInstallation of Outlet Assembly Panels 211LC and 212LC
TASK 25-13-41-400-805-A
Installation of Outlet Assembly Panels 211LC and 212LC
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Consumable Materials
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 25-13-41-860-053-A
Subtask 25-13-41-420-061-A
Subtask 25-13-41-410-053-A Subtask 25-13-41-860-054-A
[Rev.10 from 2021]
2026.03.31 23:28:59 UTC
Installation of Outlet Assembly Panels 211LC and 212LC
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Consumable Materials
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.04JMD9) | Top Coat Polyurethane-- Decorative Furnishing |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 211 | COCKPIT |
| 212 | COCKPIT |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-42-00-861-001-A | Energize the Ground Service Network from the External Power |
| TASK 24-42-00-862-001-A | De-energize the Ground Service Network Supplied from the External Power |
| TASK 25-13-41-000-001-A | Removal of the Ceiling Panels |
| TASK 25-13-41-400-001-A | Installation of the Ceiling Panels |
Outlet Assembly Panels 211LC and 212LCSubtask 25-13-41-860-053-A
A. Aircraft Maintenance Configuration
(1) Make sure that the ground service network is energized
(Ref. AMM TASK 24-42-00-861-001).
Subtask 25-13-41-010-051-A (1) Make sure that the ground service network is energized
(Ref. AMM TASK 24-42-00-861-001).
B. Get Access
(1) Make sure that the adjacent ceiling panels are removed (Ref. AMM TASK 25-13-41-000-001).
4. Procedure(1) Make sure that the adjacent ceiling panels are removed (Ref. AMM TASK 25-13-41-000-001).
Subtask 25-13-41-420-061-A
A. Installation of Outlet Assembly Panels 211LC and 212LC
(1) Put the panel (1) in position.
(2) Put the clamps (12) in position on the duct (13).
(3) Put the duct (13) in position on panel (1) and tighten the clamps (12).
(4) Install the washer (5) and the screw (4).
(5) Tighten the screws (4).
(6) Apply a layer of Top Coat Polyurethane-- Decorative Furnishing (Material No.04JMD9) on the heads of the screw (4) and on the washer (5).
(7) Install the washers (7) and the screws (8) on the brackets (9).
(8) Tighten the screws (8).
(9) Apply a layer of Top Coat Polyurethane-- Decorative Furnishing (Material No.04JMD9) on the heads of the screws (8) and on the washers (7).
(10) Lock the fasteners (6).
(11) Install the washers (2) and (10) and the screws (3) and (11).
(12) Tighten the screws (3) and (11).
(13) Apply a layer of Top Coat Polyurethane-- Decorative Furnishing (Material No.04JMD9) on the heads of the screws (3) and (11) and on the washers (2) and (10).
Subtask 25-13-41-820-050-A (1) Put the panel (1) in position.
(2) Put the clamps (12) in position on the duct (13).
(3) Put the duct (13) in position on panel (1) and tighten the clamps (12).
(4) Install the washer (5) and the screw (4).
(5) Tighten the screws (4).
(6) Apply a layer of Top Coat Polyurethane-- Decorative Furnishing (Material No.04JMD9) on the heads of the screw (4) and on the washer (5).
(7) Install the washers (7) and the screws (8) on the brackets (9).
(8) Tighten the screws (8).
(9) Apply a layer of Top Coat Polyurethane-- Decorative Furnishing (Material No.04JMD9) on the heads of the screws (8) and on the washers (7).
(10) Lock the fasteners (6).
(11) Install the washers (2) and (10) and the screws (3) and (11).
(12) Tighten the screws (3) and (11).
(13) Apply a layer of Top Coat Polyurethane-- Decorative Furnishing (Material No.04JMD9) on the heads of the screws (3) and (11) and on the washers (2) and (10).
B. Check of Clearances
(1) Make sure that clearance J1 between the panels (1) is 8 -3 mm or +3 mm (0.31 -0.12 in. or +0.12 in.).
(2) Make sure that clearance J2 between the panel (1) and the adjacent panel is 8 -3 mm or +3 mm (0.31 -0.12 in. or +0.12 in.).
5. Close-up(1) Make sure that clearance J1 between the panels (1) is 8 -3 mm or +3 mm (0.31 -0.12 in. or +0.12 in.).
(2) Make sure that clearance J2 between the panel (1) and the adjacent panel is 8 -3 mm or +3 mm (0.31 -0.12 in. or +0.12 in.).
Subtask 25-13-41-410-053-A Subtask 25-13-41-860-054-A
B. Aircraft Maintenance Configuration
(1) De-energize the ground service network
(Ref. AMM TASK 24-42-00-862-001).
(1) De-energize the ground service network
(Ref. AMM TASK 24-42-00-862-001).