Programming of a NON SMOKER A/C

TASK 23-73-00-860-006-A
Programming of a NON SMOKER A/C

ZONE: 200

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
200	UPPER HALF FUSELAGE

B. Referenced Information

REFERENCE	DESIGNATION
TASK 23-73-00-861-001-A	Energize the Cabin Intercommunication Data System (CIDS)
TASK 24-41-00-861-002-A	Energize the Aircraft Electrical Circuits from the External Power
TASK 24-41-00-861-002-A-01	Energize the Aircraft Electrical Circuits from the APU
TASK 24-41-00-861-002-A-02	Energize the Aircraft Electrical Circuits from Engine 1(2)
Programming of a NON SMOKER A/C

3. Job Set-up
Subtask 23-73-00-860-144-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).
(2) Make sure that the Cabin Intercommunication Data System (CIDS) is energized
(Ref. AMM TASK 23-73-00-861-001).

Subtask 23-73-00-865-164-A ** ON A/C NOT FOR ALL

B. Make sure that this(these) circuit breaker(s) is(are) closed:

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	ENGINE/2/FADEC A/AND EIU 2	2KS2	A05
49VU	ENGINE/1/FADEC A/AND EIU 1	2KS1	A04
49VU	L/G/LGCIU/SYS1/NORM	1GA	C09
49VU	AIR COND/CAB/PRESS/CTL1	1HL	D09
121VU	ENGINE/ENG2/FADEC B	4KS2	Q40
121VU	HYDRAULIC/LGCIU/SYS2	2GA	Q35
121VU	ENGINE/ENG1/FADEC B/AND EIU 1	4KS1	R41
122VU	AIR COND/CAB PRESS/CTL/2	2HL	Y22

4. Procedure
Subtask 23-73-00-869-073-A ** ON A/C NOT FOR ALL

A. Programming of a NON SMOKER A/C

Programming of a NON SMOKER A/C ** ON A/C NOT FOR ALL

(1) On the Programming and Test Panel (PTP) 110RH, push the DSPL ON membrane switch.

the CIDS menu page shows.

(2) Push the <PROGRAMMING related membrane switch.

the PROGRAMMING menu page shows.

(3) Push the <ZONING related membrane switch.

the ZONING menu page shows.

(4) Push the NS SIGNS> related membrane switch.

the NS SIGNS / NORMAL SIGNS MODE menu page shows.

NOTE: If the NS SIGNS / NON SMOKER A/C SELECTED page shows, a NON SMOKER A/C is already programmed.

(5) Push the NON SMKR A/C> related membrane switch.

the NS SIGNS / NON SMOKER A/C SELECTED status shows.
in the cabin, all NS SIGNS come on.
in the cabin, you hear a single LO chime.

(6) Push the <RET related membrane switch to save the new configuration to layout M.

the message PARAMETER SAVING flashes a few seconds and the menu PARAMETER SAVED with the modification number shows.

(7) Push the <RET related membrane switch.

5. Close-up
Subtask 23-73-00-869-075-A ** ON A/C NOT FOR ALL

A. Push the DSPL ON membrane switch.

[Rev.10 from 2021] 2026.04.01 05:37:34 UTC