DOC AIRBUS | AMM A320FCabin Zones Programming
TASK 23-73-00-860-003-A
Cabin Zones Programming
Self explanatory
2. Job Set-up Information
A. Work Zones and Access Panels
B. Referenced Information
3. Job Set-up
Subtask 23-73-00-860-136-A ** ON A/C NOT FOR ALL
Subtask 23-73-00-869-065-A ** ON A/C NOT FOR ALL
Subtask 23-73-00-869-068-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 05:37:32 UTC
Cabin Zones Programming
ZONE: 200
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Work Zones and Access Panels
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 200 | UPPER HALF FUSELAGE |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 23-73-00-861-001-A | Energize the Cabin Intercommunication Data System (CIDS) |
| TASK 24-41-00-861-002-A | Energize the Aircraft Electrical Circuits from the External Power |
| TASK 24-41-00-861-002-A-01 | Energize the Aircraft Electrical Circuits from the APU |
| TASK 24-41-00-861-002-A-02 | Energize the Aircraft Electrical Circuits from Engine 1(2) |
Cabin Zones Programming ExampleSubtask 23-73-00-860-136-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).
(2) Make sure that the Cabin Intercommunication Data System (CIDS) is energized
(Ref. AMM TASK 23-73-00-861-001).
Subtask 23-73-00-865-149-A ** ON A/C NOT FOR ALL (1) Energize the aircraft electrical circuits
(Ref. AMM TASK 24-41-00-861-002).
(2) Make sure that the Cabin Intercommunication Data System (CIDS) is energized
(Ref. AMM TASK 23-73-00-861-001).
B. Make sure that this(these) circuit breaker(s) is(are) closed:
4. Procedure| PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | ENGINE/2/FADEC A/AND EIU 2 | 2KS2 | A05 |
| 49VU | ENGINE/1/FADEC A/AND EIU 1 | 2KS1 | A04 |
| 49VU | L/G/LGCIU/SYS1/NORM | 1GA | C09 |
| 49VU | AIR COND/CAB/PRESS/CTL1 | 1HL | D09 |
| 121VU | ENGINE/ENG2/FADEC B | 4KS2 | Q40 |
| 121VU | HYDRAULIC/LGCIU/SYS2 | 2GA | Q35 |
| 121VU | ENGINE/ENG1/FADEC B/AND EIU 1 | 4KS1 | R41 |
| 122VU | AIR COND/CAB PRESS/CTL/2 | 2HL | Y22 |
Subtask 23-73-00-869-065-A ** ON A/C NOT FOR ALL
A. Programming of cabin zones
(1) On the PTP 110RH push the DSPL ON membrane switch.
(6) Push the related membrane switch to push the scratchpad field to the selected data field.
(7) Push the <RET related membrane switch to save the new config to layout M.
(8) The message PARAMETER SAVING flashes a few seconds and the menu PARAMETER SAVED with the modification number comes on.
(9) Push the <RET related membrane switch.
Subtask 23-73-00-869-066-A ** ON A/C NOT FOR ALL (1) On the PTP 110RH push the DSPL ON membrane switch.
- the CIDS menu page comes on.
- the PROGRAMMING menu page comes on.
- the ZONING menu page comes on.
- the CABIN ZONES menu page comes on.
(6) Push the related membrane switch to push the scratchpad field to the selected data field.
(7) Push the <RET related membrane switch to save the new config to layout M.
(8) The message PARAMETER SAVING flashes a few seconds and the menu PARAMETER SAVED with the modification number comes on.
(9) Push the <RET related membrane switch.
B. Programming of No Smoking Zones
(1) On the PTP 110RH push the DSPL ON membrane switch.
(6) Push the related membrane switch to push the scratchpad field to the selected data field.
(7) Push the <RET related membrane switch to save the new config to layout M.
(8) The message PARAMETER SAVING flashes a few seconds and the menu PARAMETER SAVED with the modification number comes on.
(9) Push the <RET related membrane switch.
Subtask 23-73-00-869-067-A ** ON A/C NOT FOR ALL (1) On the PTP 110RH push the DSPL ON membrane switch.
- the CIDS menu page comes on.
- the PROGRAMMING menu page comes on.
- the ZONING menu page comes on.
- the NS END ZONES menu page comes on.
NOTE: If a NON SMOKER A/C is programmed, the NS SIGNS / NON SMOKER A/C SELECTED page comes on. To program a smoker area push the NORMAL> related membrane switch.
(5) Enter the number of the seatrow number to the scratchpad field. (6) Push the related membrane switch to push the scratchpad field to the selected data field.
(7) Push the <RET related membrane switch to save the new config to layout M.
(8) The message PARAMETER SAVING flashes a few seconds and the menu PARAMETER SAVED with the modification number comes on.
(9) Push the <RET related membrane switch.
C. Activation - Deactivation of the Active Class Divider
(1) On the PTP 110RH push the DSPL ON membrane switch.
(7) The message PARAMETER SAVING flashes a few seconds and the menu PARAMETER SAVED with the modification number comes on.
(8) Push the <RET related membrane switch.
5. Close-up(1) On the PTP 110RH push the DSPL ON membrane switch.
- the CIDS menu page comes on.
- the PROGRAMMING menu page comes on.
- the ZONING menu page comes on.
- the CLASS DIVIDER menu page comes on.
NOTE: Pushing the membrane switch changes the active class divider to passive and the passive to the active condition.
(6) Push the <RET related membrane switch. (7) The message PARAMETER SAVING flashes a few seconds and the menu PARAMETER SAVED with the modification number comes on.
(8) Push the <RET related membrane switch.
Subtask 23-73-00-869-068-A ** ON A/C NOT FOR ALL
A. Push the DSPL On pushbutton switch.