Installation of the Left or Right Supply Pipe of the Door-Opening Actuator [CFMB]

TASK 78-31-49-400-029-A
Installation of the Left or Right Supply Pipe of the Door-Opening Actuator

WARNING: WEAR A FACE SHIELD WHICH IS RESISTANT TO HIGH PRESSURE JETS WHEN YOU WORK ON PRESSURIZED SYSTEMS.

WARNING: DO NOT GET THE FLUID ON YOUR SKIN OR IN YOUR EYES. IF YOU DO:

FLUSH IT AWAY WITH CLEAN WATER
GET MEDICAL AID.

CAUTION: USE TWO WRENCHES TO REMOVE OR INSTALL THE TUBE COUPLING NUTS:

ONE WRENCH TO HOLD THE UNION, AND
ONE TO LOOSEN OR TIGHTEN THE COUPLING NUT.

THIS PREVENTS DAMAGE TO THE PARTS.

CAUTION: MAKE SURE THERE IS NO UNWANTED MATERIAL IN THE PORTS AND ORIFICES OR DAMAGE CAN OCCUR.

CAUTION: YOU MUST INSTALL HYDRAULIC TUBES WITH HYDRAULIC FLUID AS LUBRICANT.

FIN: 1000EM1 ** ON A/C NOT FOR ALL
FIN: 1000EM2 ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 1M(3 FT)
No specific	AR	WARNING NOTICE(S)
No specific	Torque wrench: range to between 80 and 70 lbf.in (0.90 and 0.79 m.daN )
No specific	Torque wrench: range to between 150 and 130 lbf.in (1.70 and 1.47 m.daN )

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.CP2245)	finish paint EA4 blue 5991

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL, 438AR, 451AL, 452AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR, 461AL, 462AR

D. Referenced Information

REFERENCE	DESIGNATION
TASK 71-13-00-010-040-B	Opening of the Fan Cowl Doors
TASK 71-13-00-410-040-B	Closing of the Fan Cowl Doors
TASK 78-30-00-081-041-B	Make the Thrust Reverser Serviceable after Maintenance
TASK 78-30-00-481-041-B	Make the Thrust Reverser Unserviceable for Maintenance
TASK 78-36-00-010-040-B	Opening of the Thrust Reverser Doors
TASK 78-36-00-410-040-B	Closing of the Thrust Reverser Doors
Supply Pipe of the Door-Opening Actuator

3. Job Set-up
Subtask 78-31-49-860-095-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a WARNING NOTICE(S) is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a WARNING NOTICE(S) is in position to tell persons not to energize the FADEC 1(2).
(3) Make sure that the ACCESS PLATFORM 1M(3 FT) is in position.

Subtask 78-31-49-010-155-A ** ON A/C NOT FOR ALL

B. Get Access
(1) Make sure that the fan cowl doors are open: (Ref. AMM TASK 71-13-00-010-040)
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(2) Make sure that the thrust reverser doors are open: (Ref. AMM TASK 78-36-00-010-040)
(a) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(b) FOR [1000EM2] (ENGINE-2)
461AL 462AR

Subtask 78-31-49-040-129-A ** ON A/C NOT FOR ALL

C. Make sure that the thrust reverser is unserviceable (Ref. AMM TASK 78-30-00-481-041).

4. Procedure
Subtask 78-31-49-420-086-A ** ON A/C NOT FOR ALL

A. Installation of the Left or Right Supply Pipe of the Door-Opening Actuator
(1) Remove the protective covers from the pipe ends.
(2) Put the supply pipe in position on the forward frame.
(3) Connect the supply pipe to the hydraulic junction box and the inner supply pipe.
(4) TORQUE the coupling nuts to between 150 and 130 lbf.in (1.70 and 1.47 m.daN )

.
(5) Attach the supply pipe to the forward frame with the clamps and bolts.
(6) TORQUE the bolts to between 80 and 70 lbf.in (0.90 and 0.79 m.daN )

NOTE: Apply a witness line of finish paint EA4 blue 5991 (Material No.CP2245) on all nuts and connections after they are torqued.

5. Close-up
Subtask 78-31-49-410-099-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the thrust reverser doors: (Ref. AMM TASK 78-36-00-410-040)
(a) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(b) FOR [1000EM2] (ENGINE-2)
461AL 462AR

Subtask 78-31-49-440-090-A ** ON A/C NOT FOR ALL

B. Make the thrust reverser serviceable (Ref. AMM TASK 78-30-00-081-041).

Subtask 78-31-49-410-100-A ** ON A/C NOT FOR ALL

C. Close Access
(1) Close the fan cowl doors: (Ref. AMM TASK 71-13-00-410-040)
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(2) Remove the access platform(s).
(3) Remove the WARNING NOTICE(S).

[Rev.10 from 2021] 2026.04.01 03:25:27 UTC