Inspection of the ACC Front Duct [IAE]

TASK 75-24-47-200-010-A
Inspection of the ACC Front Duct

FIN: 1000EM1 ** ON A/C NOT FOR ALL
FIN: 1000EM2 ** ON A/C NOT FOR ALL

1. Reason for the Job
This TASK gives the procedure for the inspection of the ACC Front Duct.
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL, 438AR, 452AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR, 462AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 71-13-00-010-010-A	Opening of the Fan Cowls 437AL(447AL),438AR(448AR)
TASK 71-13-00-410-010-A	Closing of the Fan Cowls 437AL(447AL),438AR(448AR)
TASK 78-30-00-040-012-A	Deactivation of the Thrust Reverser Hydraulic Control Unit (HCU) for Ground Maintenance
TASK 78-30-00-440-012-A	Re-activation of the Thrust Reverser Hydraulic Control Unit (HCU) after Ground Maintenance
TASK 78-32-00-010-010-A	Opening of the Thrust Reverser Halves
TASK 78-32-00-410-010-A	Closing of the Thrust Reverser Halves
HP/LP ACC Ducts

3. Job Set-up
Subtask 75-24-47-941-050-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).

Subtask 75-24-47-010-050-A ** ON A/C NOT FOR ALL

B. Open the fan cowls (Ref. AMM TASK 71-13-00-010-010):
(1) FOR [1000EM1] (ENGINE-1)
437AL 438AR.
(2) FOR [1000EM2] (ENGINE-2)
447AL 448AR.

Subtask 75-24-47-040-050-A ** ON A/C NOT FOR ALL

C. Deactivate the thrust reverser.

WARNING: MAKE SURE THAT THE THRUST REVERSER HYDRAULIC CONTROL UNIT (HCU) IS DEACTIVATED BEFORE YOU DO WORK ON OR AROUND THE THRUST REVERSER. IF THE HCU IS NOT DEACTIVATED, THERE IS A RISK OF UNWANTED THRUST REVERSER OPERATION WHICH CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.

(1) Deactivate the thrust reverser hydraulic control unit (HCU) (Ref. AMM TASK 78-30-00-040-012).

Subtask 75-24-47-010-051-A ** ON A/C NOT FOR ALL

D. Open the right thrust reverser half (Ref. AMM TASK 78-32-00-010-010):
(1) FOR [1000EM1] (ENGINE-1)
452AR
(2) FOR [1000EM2] (ENGINE-2)
462AR.

4. Procedure
Subtask 75-24-47-210-050-A ** ON A/C NOT FOR ALL

A. Inspect the ACC Front Duct
(1) Visually examine the ACC front duct for external damage
(a) Cracks - If any crack is found, reject the ACC front duct.
(b) Dents - If there is any dent with a sharp edge or which is more than 0.025 in. (0.63mm) in depth, reject the ACC front duct.
(c) Wear - If any wear is found on the ACC front duct front flange, reject the duct.

5. Close-up
Subtask 75-24-47-410-050-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Close the right thrust reverser half (Ref. AMM TASK 78-32-00-410-010):
(a) FOR [1000EM1] (ENGINE-1)
452AR.
(b) FOR [1000EM2] (ENGINE-2)
462AR.

Subtask 75-24-47-440-050-A ** ON A/C NOT FOR ALL

B. Activate the thrust reverser HCU (Ref. AMM TASK 78-30-00-440-012).

Subtask 75-24-47-410-051-A ** ON A/C NOT FOR ALL

C. Close Access
(1) Close the fan cowls (Ref. AMM TASK 71-13-00-410-010):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR.
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR.
(2) Remove the WARNING NOTICE(S).

[Rev.10 from 2021] 2026.04.01 03:11:24 UTC