DOC AIRBUS | AMM A320FRemoval of J7 Harness [CFMI]
TASK 73-21-50-000-006-A
Removal of J7 Harness
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 73-21-50-941-055-A ** ON A/C NOT FOR ALL
Subtask 73-21-50-020-097-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 13:04:58 UTC
Removal of J7 Harness
1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | CAP - BLANKING |
| No specific | AR | WARNING NOTICE(S) |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| FOR [1000EM1] (ENGINE-1) | |
| 451AL, 452AR | |
| FOR [1000EM2] (ENGINE-2) | |
| 437AL, 438AR, 447AL, 448AR, 461AL, 462AR | |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 71-13-00-010-040-A | Opening of the Fan Cowl Doors |
| TASK 78-30-00-481-041-A | Make the Thrust Reverser Unserviceable for Maintenance |
| TASK 78-36-00-010-040-A | Opening of the Thrust Reverser Doors |
J7 HarnessSubtask 73-21-50-941-055-A ** ON A/C NOT FOR ALL
A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).
(4) This harness is connected from Electronic Control Unit (ECU) to ECU cooling valve, N2 speed sensor, Hydromechanical Unit (HMU) and fuel return valve.
Subtask 73-21-50-010-055-A ** ON A/C NOT FOR ALL (1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).
(4) This harness is connected from Electronic Control Unit (ECU) to ECU cooling valve, N2 speed sensor, Hydromechanical Unit (HMU) and fuel return valve.
B. Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-040):
(1) FOR [1000EM2] (ENGINE-2)
437AL 438AR
(2) FOR [1000EM2] (ENGINE-2)
447AL 448AR
Subtask 73-21-50-040-060-A ** ON A/C NOT FOR ALL Subtask 73-21-50-010-076-A ** ON A/C NOT FOR ALL (1) FOR [1000EM2] (ENGINE-2)
437AL 438AR
(2) FOR [1000EM2] (ENGINE-2)
447AL 448AR
D. Open the thrust reverser doors (Ref. AMM TASK 78-36-00-010-040):
(1) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(2) FOR [1000EM2] (ENGINE-2)
461AL 462AR
4. Procedure(1) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(2) FOR [1000EM2] (ENGINE-2)
461AL 462AR
Subtask 73-21-50-020-097-A ** ON A/C NOT FOR ALL
A. Removal of the J7 harness
PRE SB CFM 72-519
(1) Disconnect the electrical harness from the fuel return valve, the HMU, the N2 speed sensor, the ECU cooling valve and the ECU.
POST SB CFM 72-519
(2) Disconnect the electrical harness from the fuel return valve, the HMU, the N2 speed sensor and the ECU.
END OF SB CFM 72-519
PRE SB 72-169
(3) Remove the 2 bolts (82) and nuts (84) which attach the cover plate (85) to the brackets at the 5 o'clock location on the flanges G and E (detail A). Pull the flexible clamp assembly from the brackets and pull out the J7 harness from the flexible clamp (81). Re-install the clamp assembly.
POST SB 72-169
(4) Remove the 2 bolts (82) and nuts (84) which attach the cover plate (85) to the brackets at the 5 o'clock location on the flange G and E (detail A), with clamp (83) of J15 harness. Pull out the J7 harness from the flexible clamp (81). Re-install the clamp assembly.
END OF SB 72-169
PRE SB CFM 72-519
(5) Remove the bolt (87) and nut (88) which attach the J7 and J8 harmesses clamps to the same bracket as above (detail B).
(6) Remove the bolt (90) which attaches the J7 and J8 harnesses clamps to the same bracket as above (detail C).
POST SB CFM 72-519
(7) Not applicable
END OF SB CFM 72-519
(8) Remove the 2 bolts (91) which attach the J7 and J8 harnesses to the bracket at the 5.30 o'clock location between the flanges G and E (detail D)
Remove the bolt (92) which attaches the J7 and J8 harnesses to the left leg of the same bracket (detail E)
(9) Remove the bolt (105) which attaches the J7 harness to the bracket attached to flange G on the left side of the 6 o'clock location (detail F). Remove the J8 and J7 harnesses from the clips on the same bracket, then remove the J7 harness from the J8 harness clip.
(10) Remove the bolt (106) which attaches the J7 harness to the left Accessory Gearbox (AGB) bracket (detail G).
(11) Remove the bolt (108) which attaches the J7 harness to the left bracket of the AGB/Transfer Gearbox (TGB) interface (detail H).
Remove the J8 and J7 harnesses from the clips on 3 brackets at the 6:30 o'clock, 7 'oclock and 7:30 o'clock locations on flange E, then remove the J8 harness from the J7 harness clips (details I, J and K).
(12) Remove the bolt (111) which attaches the J7 and J8 harnesses to the bracket at the 8 o'clock location on flange D (detail L).
PRE SB 72-169
PRE SB CFM 72-519
(13) Remove the bolt (95) which attaches the J7 and J8 harnesses to the bracket at the 5:30 o'clock location on flange G (detail M).
POST SB 72-169
(14) Remove the nut (96) and bolt (95) which attach J7 and J8 harnesses to the bracket at the 5:30 o'clock location on flange G (detail M) with bleed bias tubes.
END OF SB 72-169
(15) Remove the J7 harness from the clip on the bracket at the 4.30 o'clock location on flange E (detail N), under the Electrical Control Unit (ECU).
PRE SB 72-169
(16) Remove the bolt (98) which attaches the J7 and J8 harnesses to the bracket at the 4 o'clock location on flange E (detail O).
POST SB 72-169
(17) Remove the bolt (99) which attaches the J7 harness to the bracket at the 4 o'clock location on flange E (detail O).
END OF SB 72-169
(18) Remove the bolt (101) which attaches the J7 and J8 harnesses to the same bracket at the 3:30 o'clock location (detail P).
(19) Remove the bolt (102) which attaches the J7 and J8 harnesses to the bracket on the right side of 3 o'clock location on flange E (detail Q).
POST SB CFM 72-519
(20) Not applicable
END OF SB CFM 72-519
(21) Remove J7 harness.
(22) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(23) Remove all the clamps from the harness.
PRE SB CFM 72-519
(1) Disconnect the electrical harness from the fuel return valve, the HMU, the N2 speed sensor, the ECU cooling valve and the ECU.
POST SB CFM 72-519
(2) Disconnect the electrical harness from the fuel return valve, the HMU, the N2 speed sensor and the ECU.
END OF SB CFM 72-519
PRE SB 72-169
(3) Remove the 2 bolts (82) and nuts (84) which attach the cover plate (85) to the brackets at the 5 o'clock location on the flanges G and E (detail A). Pull the flexible clamp assembly from the brackets and pull out the J7 harness from the flexible clamp (81). Re-install the clamp assembly.
POST SB 72-169
(4) Remove the 2 bolts (82) and nuts (84) which attach the cover plate (85) to the brackets at the 5 o'clock location on the flange G and E (detail A), with clamp (83) of J15 harness. Pull out the J7 harness from the flexible clamp (81). Re-install the clamp assembly.
END OF SB 72-169
PRE SB CFM 72-519
(5) Remove the bolt (87) and nut (88) which attach the J7 and J8 harmesses clamps to the same bracket as above (detail B).
(6) Remove the bolt (90) which attaches the J7 and J8 harnesses clamps to the same bracket as above (detail C).
POST SB CFM 72-519
(7) Not applicable
END OF SB CFM 72-519
(8) Remove the 2 bolts (91) which attach the J7 and J8 harnesses to the bracket at the 5.30 o'clock location between the flanges G and E (detail D)
Remove the bolt (92) which attaches the J7 and J8 harnesses to the left leg of the same bracket (detail E)
(9) Remove the bolt (105) which attaches the J7 harness to the bracket attached to flange G on the left side of the 6 o'clock location (detail F). Remove the J8 and J7 harnesses from the clips on the same bracket, then remove the J7 harness from the J8 harness clip.
(10) Remove the bolt (106) which attaches the J7 harness to the left Accessory Gearbox (AGB) bracket (detail G).
(11) Remove the bolt (108) which attaches the J7 harness to the left bracket of the AGB/Transfer Gearbox (TGB) interface (detail H).
Remove the J8 and J7 harnesses from the clips on 3 brackets at the 6:30 o'clock, 7 'oclock and 7:30 o'clock locations on flange E, then remove the J8 harness from the J7 harness clips (details I, J and K).
(12) Remove the bolt (111) which attaches the J7 and J8 harnesses to the bracket at the 8 o'clock location on flange D (detail L).
PRE SB 72-169
PRE SB CFM 72-519
(13) Remove the bolt (95) which attaches the J7 and J8 harnesses to the bracket at the 5:30 o'clock location on flange G (detail M).
POST SB 72-169
(14) Remove the nut (96) and bolt (95) which attach J7 and J8 harnesses to the bracket at the 5:30 o'clock location on flange G (detail M) with bleed bias tubes.
END OF SB 72-169
(15) Remove the J7 harness from the clip on the bracket at the 4.30 o'clock location on flange E (detail N), under the Electrical Control Unit (ECU).
PRE SB 72-169
(16) Remove the bolt (98) which attaches the J7 and J8 harnesses to the bracket at the 4 o'clock location on flange E (detail O).
POST SB 72-169
(17) Remove the bolt (99) which attaches the J7 harness to the bracket at the 4 o'clock location on flange E (detail O).
END OF SB 72-169
(18) Remove the bolt (101) which attaches the J7 and J8 harnesses to the same bracket at the 3:30 o'clock location (detail P).
(19) Remove the bolt (102) which attaches the J7 and J8 harnesses to the bracket on the right side of 3 o'clock location on flange E (detail Q).
POST SB CFM 72-519
(20) Not applicable
END OF SB CFM 72-519
(21) Remove J7 harness.
(22) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(23) Remove all the clamps from the harness.