Removal of the CJ11L Harness [CFMI]

TASK 73-21-50-000-001-A
Removal of the CJ11L Harness

FIN: 1000EM1 ** ON A/C NOT FOR ALL
FIN: 1000EM2 ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	CAP - BLANKING
No specific	AR	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL, 438AR, 451AL
FOR [1000EM2] (ENGINE-2)
447AL, 448AR, 461AL

C. Referenced Information

REFERENCE	DESIGNATION
TASK 71-13-00-010-040-A	Opening of the Fan Cowl Doors
TASK 78-30-00-481-041-A	Make the Thrust Reverser Unserviceable for Maintenance
TASK 78-36-00-010-040-A	Opening of the Thrust Reverser Doors
CJ11L Harness

3. Job Set-up
Subtask 73-21-50-941-050-A ** ON A/C NOT FOR ALL

A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).

PRE SB 75-021

NOTE: This harness is connected to the J11 harness, in the 6 o'clock junction box, the Variable Bleed Valve (VBV) position sensor inner connector (core side, channel B) and the Burner Staging Valve (BSV) pressure switch (channel A).

POST SB 75-021

NOTE: This harness is connected to the J11 harness, in the 6 o'clock junction box, the Variable Bleed Valve (VBV) position sensor inner connector (core side, channel A) and the Burner Staging Valve (BSV) pressure switch (channel A).

Subtask 73-21-50-010-050-A ** ON A/C NOT FOR ALL

B. Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-040):
(1) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(a) FOR [1000EM2] (ENGINE-2)
447AL 448AR

Subtask 73-21-50-040-050-A ** ON A/C NOT FOR ALL

C. Make the thrust reverser unserviceable (Ref. AMM TASK 78-30-00-481-041).

Subtask 73-21-50-010-065-A ** ON A/C NOT FOR ALL

D. Open the left thrust reverser door (Ref. AMM TASK 78-36-00-010-040):
(1) FOR [1000EM1] (ENGINE-1)
451AL
(2) FOR [1000EM2] (ENGINE-2)
461AL

4. Procedure
Subtask 73-21-50-020-092-A ** ON A/C NOT FOR ALL

A. Removal of the CJ11L Harness
(1) Disconnect the electrical harness from the VBV position sensor and from the BSV pressure switch and disconnect the J11 harness from the connector in the 6 o'clock junction box.
(2) Remove the nut (2) which attaches the CJ11L connector to the 6 o'clock junction box (view W). Remove O-ring (18).
(3) Remove the loop clamps that attach the electrical harnesses. To do this, remove the bolts from the items which follow:
(a) The clamp on the VBV gear motor (detail A)
(b) The bracket at the 8 o'clock location on the core engine (detail B)
(c) The bracket at the 7 o'clock location on the core engine (detail C).

PRE SB 72-019

(d) Remove nut (9).

POST SB 72-019

(e) Not applicable

END OF SB 72-019

(f) The support on the left side of the 6 o'clock junction box (detail D).
(g) The bracket on the rear face of the 6 o'clock junction box (detail E)
(4) Remove the CJ11L harness.
(5) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
(6) Remove all the clamps from the harness.

[Rev.10 from 2021] 2026.04.01 02:56:09 UTC