Removal of the Fuel Nozzles [CFML]

TASK 73-11-30-000-802-A
Removal of the Fuel Nozzles

WARNING: BE CAREFUL WHEN YOU DO WORK ON THE ENGINE PARTS AFTER THE ENGINE SHUTDOWN. USE APPLICABLE THERMAL GLOVES. THE ENGINE PARTS CAN STAY HOT FOR ONE HOUR AFTER SHUTDOWN AND CAN BURN YOU.

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

ZONE: 400
ZONE: 410
ZONE: 420
FIN: 2005EM1
FIN: 2005EM2

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 1M(3 FT)
No specific	AR	WARNING NOTICE(S)

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
400	POWER PLANT, NACELLES AND PYLONS
410	ENG 1 PYLON BOX AND FORWARD FAIRING
420	ENG 2 PYLON BOX AND FORWARD FAIRING
FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENGINE 1)
437AL, 438AR, 451AL, 452AR
FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENGINE 2)
447AL, 448AR, 461AL, 462AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 71-13-00-010-803-A	Opening of the Fan Cowl Doors
TASK 73-11-30-000-803-A	Removal of Full Set Fuel Nozzles
TASK 78-30-00-040-809-A	Deactivation of the Thrust Reverser System for Ground Maintenance
TASK 78-36-00-010-806-A	Opening of the Thrust Reverser Cowl Doors

3. Job Set-up
Subtask 73-11-30-941-055-A

A. Safety Precautions
(1) On the center pedestal, on ENG panel 115VU:
(a) Make sure that the ENG/MODE selector switch is in the NORM position.
(b) Make sure that the ENG/MASTER 1(2) control switch was in the OFF position not less than five minutes before you do this procedure.
(c) Put WARNING NOTICE(S) in position to tell persons not to operate:

The ENG/MODE selector switch
The ENG/MASTER 1(2) control switch.

(2) On the ENG section of maintenance panel 50VU:
(a) Make sure that the ON legend of the FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a WARNING NOTICE(S) in position to tell persons not to energize FADEC 1(2).

Subtask 73-11-30-010-061-A

B. Get Access
(1) Open the fan cowl doors (Ref. AMM TASK 71-13-00-010-803):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENGINE 1)
437AL 438AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENGINE 2)
447AL 448AR

Subtask 73-11-30-040-056-A

C. Deactivation of the Thrust Reverser System for Maintenance

WARNING: YOU MUST DEACTIVATE THE THRUST REVERSER BEFORE YOU DO WORK ON OR AROUND IT. IF YOU DO NOT, THE THRUST REVERSER CAN OPERATE ACCIDENTALLY AND CAUSE AN INJURY AND/OR DAMAGE.

(1) Do the deactivation of the thrust reverser system for ground maintenance (Ref. AMM TASK 78-30-00-040-809).

Subtask 73-11-30-010-062-A

D. Get Access
(1) Open the thrust reverser cowl-doors (Ref. AMM TASK 78-36-00-010-806):
(a) FOR [4020KM1] (POWER PLANT-DEMOUNTABLE, ENGINE 1)
451AL 452AR
(b) FOR [4020KM2] (POWER PLANT-DEMOUNTABLE, ENGINE 2)
461AL 462AR
(2) Put an ACCESS PLATFORM 1M(3 FT) in position.

4. Procedure

WARNING: BE CAREFUL NOT TO GET AIRCRAFT FUEL IN YOUR MOUTH OR IN YOUR EYES. IF YOU GET FUEL ON YOUR SKIN OR ON YOUR CLOTHES, FLUSH IT IMMEDIATELY WITH WATER. IF NECESSARY, GET MEDICAL HELP. AIRCRAFT FUEL IS POISONOUS.

CAUTION: USE TWO WRENCHES TO LOOSEN THE TUBE COUPLING NUTS. USE ONE WRENCH TO HOLD THE NIPPLE FITTING. USE THE OTHER WRENCH TO LOOSEN THE COUPLING NUT. IF THE NIPPLE FITTING TURNS, DAMAGE CAN OCCUR.

CAUTION: USE PLIERS THAT HAVE TEFLON JAWS TO TIGHTEN OR LOOSEN THE ELECTRICAL CONNECTORS. DO NOT USE PLIERS THAT HAVE METAL JAWS. METAL JAWS CAN CAUSE DAMAGE TO THE ELECTRICAL CONNECTORS.

Subtask 73-11-30-020-071-A

A. General
(1) Remove the nozzles as a set, refer to (Ref. AMM TASK 73-11-30-000-803).

[Rev.10 from 2021] 2026.04.01 13:06:52 UTC