Installation of the Fan Case Liner Panels [IAE]

TASK 72-32-87-400-011-B
Installation of the Fan Case Liner Panels

ZONE: 400
FIN: 1000EM1 ** ON A/C NOT FOR ALL
FIN: 1000EM2 ** ON A/C NOT FOR ALL

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE
No specific	AR	WARNING NOTICE(S)
No specific	Torque wrench: range to between 85 and 75 lbf.in (0.96 and 0.85 m.daN )

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
400	POWER PLANT, NACELLES AND PYLONS
FOR [1000EM1] (ENGINE-1)
437AL, 438AR, 451AL, 452AR
FOR [1000EM2] (ENGINE-2)
447AL, 448AR, 461AL, 462AR

C. Referenced Information

REFERENCE	DESIGNATION
TASK 70-23-11-911-013-A	General Torque Tightening Techniques
TASK 71-13-00-010-010-A	Opening of the Fan Cowls 437AL(447AL),438AR(448AR)
TASK 71-13-00-410-010-A	Closing of the Fan Cowls 437AL(447AL),438AR(448AR)
TASK 78-30-00-040-012-A	Deactivation of the Thrust Reverser Hydraulic Control Unit (HCU) for Ground Maintenance
TASK 78-30-00-440-012-A	Re-activation of the Thrust Reverser Hydraulic Control Unit (HCU) after Ground Maintenance
TASK 78-32-00-010-010-A	Opening of the Thrust Reverser Halves
TASK 78-32-00-410-010-A	Closing of the Thrust Reverser Halves
Positions of the Screws to attach the Fan Case Liner Panels
Positions of the Screws to attach the Fan Case Liner Panels
Protection Cover

3. Job Set-up
Subtask 72-32-87-860-053-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a WARNING NOTICE(S) is in position to tell persons not to start the engine.
(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a WARNING NOTICE(S) is in position to tell persons not to energize the FADEC 1(2).
(3) Make sure that the ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE is in position.

Subtask 72-32-87-010-064-A ** ON A/C NOT FOR ALL

B. Get Access
(1) Make sure that the fan cowl doors are open: (Ref. AMM TASK 71-13-00-010-010)
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR
(2) Make sure that the thrust reverser doors are open: (Ref. AMM TASK 78-32-00-010-010)
(a) FOR [1000EM1] (ENGINE-1)
451AL 452AR
(b) FOR [1000EM2] (ENGINE-2)
461AL 462AR

Subtask 72-32-87-040-060-A ** ON A/C NOT FOR ALL

C. Make sure that the thrust reverser Hydraulic Control Unit (HCU) is deactivated: (Ref. AMM TASK 78-30-00-040-012)

Subtask 72-32-87-110-051-A ** ON A/C NOT FOR ALL

D. Make sure that all the mating faces of the fan case liner panels are clean.

4. Procedure
Subtask 72-32-87-420-053-A ** ON A/C NOT FOR ALL

A. Install the replacement fan case liner panels.
(1) Install the fan case rear liner panels and attach them with the screws. Tighten the screws lightly.

Positions of the Screws to attach the Fan Case Liner Panels ** ON A/C NOT FOR ALL

(2) Install the fan case front liner panels and attach them with the screws. Tighten the screws lightly.

Positions of the Screws to attach the Fan Case Liner Panels ** ON A/C NOT FOR ALL

(3) Adjust the positions of the fan case liner panels to make a minimum clearance between the front and the rear panels.
(4) TORQUE the screws to between 85 and 75 lbf.in (0.96 and 0.85 m.daN )

(Ref. AMM TASK 70-23-11-911-013).

Subtask 72-32-87-630-053-A ** ON A/C NOT FOR ALL

B. Remove the protection cover, IAE 1J12187 or equivalent, from the bleed duct.

Protection Cover ** ON A/C NOT FOR ALL

5. Close-up
Subtask 72-32-87-410-056-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the thrust reverser halves (Ref. AMM TASK 78-32-00-410-010):
(a) FOR [1000EM1] (ENGINE-1)
451AL 452AR.
(b) FOR [1000EM2] (ENGINE-2)
461AL 462AR.

Subtask 72-32-87-440-053-A ** ON A/C NOT FOR ALL

B. Activate the thrust reverser HCU (Ref. AMM TASK 78-30-00-440-012).

Subtask 72-32-87-410-065-A ** ON A/C NOT FOR ALL

C. Close Access
(1) Close the fan cowls (Ref. AMM TASK 71-13-00-410-010):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR.
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR.
(2) Remove the WARNING NOTICE(S).
(3) Remove the access platform(s).

[Rev.10 from 2021] 2026.04.01 13:01:11 UTC