DOC AIRBUS | AMM A320FRemoval of the Ignition Supply Harness (Pre SBE 71-0288 only) [IAE]
TASK 71-51-44-000-010-B
Removal of the Ignition Supply Harness (Pre SBE 71-0288 only)
This task is for V2500-A5 engines.
For POST SBE 71-0288 refer to the AMM TASK 71-51-42-000-010.
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 71-51-44-941-060-A ** ON A/C NOT FOR ALL
Subtask 71-51-44-020-059-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 02:30:43 UTC
Removal of the Ignition Supply Harness (Pre SBE 71-0288 only)
WARNING:
BE CAREFUL WHEN YOU DO WORK ON THE ENGINE PARTS AFTER THE ENGINE SHUTDOWN. USE APPLICABLE THERMAL GLOVES. THE ENGINE PARTS CAN STAY HOT FOR ONE HOUR AFTER SHUTDOWN AND CAN BURN YOU.
1. Reason for the JobThis task is for V2500-A5 engines.
For POST SBE 71-0288 refer to the AMM TASK 71-51-42-000-010.
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | AR | ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE |
| No specific | AR | COVER - BLANKING |
| No specific | AR | SAFETY CLIP - CIRCUIT BREAKER |
| No specific | AR | WARNING NOTICE(S) |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| FOR [1000EM1] (ENGINE-1) | |
| 437AL, 438AR | |
| FOR [1000EM2] (ENGINE-2) | |
| 447AL, 448AR | |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 30-21-49-000-012-B | Removal of the Anti-ice Duct No. 3 |
| TASK 71-13-00-010-010-A | Opening of the Fan Cowls 437AL(447AL),438AR(448AR) |
| TASK 80-13-49-000-010-B | Removal of the Starter Duct |
Ignition Supply HarnessSubtask 71-51-44-941-060-A ** ON A/C NOT FOR ALL
A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) in position to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is OFF.
(b) Put a WARNING NOTICE(S) in position to tell persons not to energize the FADEC 1(2).
Subtask 71-51-44-865-074-A ** ON A/C NOT FOR ALL (1) On the center pedestal, on the ENG panel 115VU:
(a) Put a WARNING NOTICE(S) in position to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is OFF.
(b) Put a WARNING NOTICE(S) in position to tell persons not to energize the FADEC 1(2).
B. Open, safety and tag this(these) circuit breaker(s):
Subtask 71-51-44-010-066-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 49VU | ENGINE/1 AND 2/IGN/SYS A | 1JH | A03 |
| FOR FIN: 1000EM1 (ENGINE1) | |||
| 121VU | ENGINE/IGN/ENG1/SYS B | 3JH1 | P41 |
| 121VU | ENGINE/IGN/ENG1/SYS A BAT | 2JH1 | P39 |
| FOR FIN: 1000EM2 (ENGINE2) | |||
| 121VU | ENGINE/IGN/ENG2/SYS B | 3JH2 | P42 |
| 121VU | ENGINE/IGN/ENG2/SYS A BAT | 2JH2 | P40 |
C. Get Access
(1) Open the fan cowls (Ref. AMM TASK 71-13-00-010-010):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR.
(2) Put the ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position on the left side and the right side of the engine.
Subtask 71-51-44-010-067-A ** ON A/C NOT FOR ALL (1) Open the fan cowls (Ref. AMM TASK 71-13-00-010-010):
(a) FOR [1000EM1] (ENGINE-1)
437AL 438AR
(b) FOR [1000EM2] (ENGINE-2)
447AL 448AR.
(2) Put the ACCESS PLATFORM 2M (6 FT) - ADJUSTABLE in position on the left side and the right side of the engine.
D. Get Access
(1) Remove the anti-ice duct No. 3 (Ref. AMM TASK 30-21-49-000-012).
(2) Remove the starter duct (Ref. AMM TASK 80-13-49-000-010).
4. Procedure(1) Remove the anti-ice duct No. 3 (Ref. AMM TASK 30-21-49-000-012).
(2) Remove the starter duct (Ref. AMM TASK 80-13-49-000-010).
Subtask 71-51-44-020-059-A ** ON A/C NOT FOR ALL
A. Disconnection of the Harness
(1) Disconnect these electrical connectors:
(a) The connectors 4100KS-D and 4100KS-C from the relay box
(b) The connectors 4002VC-A and 4003VC-A from the electrical harness receptacles attached to the brackets
(c) The connectors 4000JH1-A and 4000JH2-A from the igniter box.
Subtask 71-51-44-620-050-A ** ON A/C NOT FOR ALL (1) Disconnect these electrical connectors:
(a) The connectors 4100KS-D and 4100KS-C from the relay box
(b) The connectors 4002VC-A and 4003VC-A from the electrical harness receptacles attached to the brackets
(c) The connectors 4000JH1-A and 4000JH2-A from the igniter box.
B. Put the applicable COVER - BLANKING on all the electrical connectors and all the electrical receptacles.
Subtask 71-51-44-020-060-A ** ON A/C NOT FOR ALL C. Disconnection of the Harness Clips from the Front of the LP Compressor/ Intermediate Case
PRE SBE 73-0140
(1) Remove the bolt (1) and the washer (2) from the clip (3) at position A.
END OF PRE SBE 73-0140
POST SBE 73-0140
(2) Remove the bolt (1), the washer (2) and the nut (4) from the clip (3) at position A.
END OF POST SBE 73-0140
(3) Remove the bolt (5), the washer (6) and the nut (8) from the clip (7) at position B.
(4) Remove the bolt (9) and the washer (10) from the clips (11) and (12) at position C.
(5) Remove the bolt (13), the washer (14) and the nut (17) from the clips (15) and (16) at position D.
Subtask 71-51-44-020-061-A ** ON A/C NOT FOR ALL PRE SBE 73-0140
(1) Remove the bolt (1) and the washer (2) from the clip (3) at position A.
END OF PRE SBE 73-0140
POST SBE 73-0140
(2) Remove the bolt (1), the washer (2) and the nut (4) from the clip (3) at position A.
END OF POST SBE 73-0140
(3) Remove the bolt (5), the washer (6) and the nut (8) from the clip (7) at position B.
(4) Remove the bolt (9) and the washer (10) from the clips (11) and (12) at position C.
(5) Remove the bolt (13), the washer (14) and the nut (17) from the clips (15) and (16) at position D.
D. Disconnection of the Harness Clips from the Rear of the LP Compressor/ Intermediate Case
PRE SBE 79-0088
(1) Remove the bolt (18), the washer (19) and the nut (21) from the clip (20) at position F.
(2) Make a note of the position of the spacer (25). Remove the bolt (28), the washers (27) and (23), the nut (22) and the spacer (25) from the clips (26) and (24) at position G.
(3) Remove the bolt (29), the washer (30) and the nut (32) from the clip (31) at position H.
END OF PRE SBE 79-0088
POST SBE 79-0088
(4) Remove the bolt (33), the washer (34) and the nut (37) from the clips (35) and (36) at position J.
(5) Make a note of the position of the spacer (41). Remove the bolt (38), the washers (39) and (44), the nut (45) and the spacer (41) from the clips (40), (42) and (43) at position K.
END OF POST SBE 79-0088
PRE SBE 72-0189
(6) Make a note of the position of the spacer (50). Remove the bolt (46), the washer (47), and the spacer (50) from the clips (48), (49) and (51) at position L.
(7) Remove the bolt (52) and the washer (53) from the clip (54) at position M.
END OF PRE SBE 72-0189
POST SBE 72-0189 and PRE SBE 79-0088
(8) Make a note of the position of the spacer (129). Remove the bolt (127) and the spacer (129) from the clip (128) at position AB.
END OF POST SBE 72-0189 and END OF PRE SBE 79-0088
POST SBE 79-0088
(9) Make a note of the position of the spacer (129). Remove the bolt (127), the washer (130) and the spacer (129) from the clip (128) at position AB.
END OF POST SBE 79-0088
POST SBE 72-0189, PRE SBE 79-0088 and POST SBE 79-0088
(10) Remove the bolt (123), the washer (124) and the nut (126) from the clip (125) at position AA.
END OF POST SBE 72-0189, END OF PRE SBE 79-0088 and END OF POST SBE 79-0088
PRE SBE 72-0189
(11) Make a note of the position of the spacer (58). Remove the bolt (55), the washer (56), the nut (59) and the spacer (58) from the clip (57) at position N.
END OF PRE SBE 72-0189
POST SBE 72-0189 and PRE SBE 79-0088
(12) Make a note of the position of the spacers (58) and (61). Remove the bolt (55), the nut (59) and the spacers (58) and (61) from the clips (57) and (60) at position N.
END OF POST SBE 72-0189 and END OF PRE SBE 79-0088
POST SBE 79-0088
(13) Make a note of the position of the spacers (58) and (61). Remove the bolt (55), the washer (56), the nut (59) and the spacers (58) and (61) from the clips (57) and (60) at position N.
END OF POST SBE 79-0088
(14) Remove the bolt (64) and the washer (63) from the clip (62) at position P.
(15) Remove the bolt (65) and the washer (66) from the clip (67) at position Q.
(16) Remove the bolt (68), the washers (69) and (72) and the nut (73) from the clips (70) and (71) at position R.
PRE SBE 72-0189 and POST SBE 79-0088
(17) Remove the bolt (74), the washers (75) and (78) and the nut (79) from the clips (76) and (77) at position S.
END OF PRE SBE 72-0189 and END OF POST SBE 79-0088
POST SBE 72-0189 and PRE SBE 79-0088
(18) Remove the bolt (74) and the nut (79) from the clips (76) and (77) at position S.
END OF POST SBE 72-0189 and END OF PRE SBE 79-0088
PRE SBE 72-0189
(19) Remove the bolt (80), the washers (81) and (84) and the nut (85) from the clips (82) and (83) at position T.
END OF PRE SBE 72-0189
POST SBE 72-0189 and PRE SBE 79-0088
(20) Make a note of the position of the spacer (86). Remove the bolt (80), the nut (85) and the spacer (86) from the clips (82) and (83) at position T.
END OF POST SBE 72-0189 and END OF PRE SBE 79-0088
POST SBE 79-0088
(21) Make a note of the position of the spacer (86). Remove the bolt (80), the washers (81) and (84), the nut (85) and the spacer (86) from the clips (82) and (83) at position T.
END OF POST SBE 79-0088
PRE SBE 72-0189
(22) Remove the bolt (87), the washers (88) and (91) and the nut (92) from the clips (89) and (90) at position U.
(23) Make a note of the position of the spacer (97). Remove the bolt (100), the washers (94) and (99), the nut (93) and the spacer (97) from the clips (95),(96) and (98) at position V.
END OF PRE SBE 72-0189
POST SBE 72-0189 and PRE SBE 79-0088
(24) Make a note of the position of the spacer (103). Remove the bolt (101) and the spacer (103) from the clip (102) at position W.
(25) Remove the bolt (104) and the nut (107) from the clips (105) and (106) at position X.
END OF POST SBE 72-0189 and END OF PRE SBE 79-0088
POST SBE 72-0189 and PRE SBE 75-0081
(26) Remove the bolt (108) and the nut (111) from the clips (109) and (110) at position Y.
END OF POST SBE 72-0189 and END OF PRE SBE 75-0081
POST SBE 72-0189 and PRE SBE 79-0088
(27) Make a note of the position of the spacer (114). Remove the bolt (112), the nut (116) and the spacer (114) from the clips (113) and (115) at position Z.
END OF POST SBE 72-0189 and END OF PRE SBE 79-0088
POST SBE 79-0088
(28) Remove the bolt (131), the washers (132) and (135) and the nut (136) from the clips (133) and (134) at position AC.
END OF POST SBE 79-0088
Subtask 71-51-44-010-068-A ** ON A/C NOT FOR ALL PRE SBE 79-0088
(1) Remove the bolt (18), the washer (19) and the nut (21) from the clip (20) at position F.
(2) Make a note of the position of the spacer (25). Remove the bolt (28), the washers (27) and (23), the nut (22) and the spacer (25) from the clips (26) and (24) at position G.
(3) Remove the bolt (29), the washer (30) and the nut (32) from the clip (31) at position H.
END OF PRE SBE 79-0088
POST SBE 79-0088
(4) Remove the bolt (33), the washer (34) and the nut (37) from the clips (35) and (36) at position J.
(5) Make a note of the position of the spacer (41). Remove the bolt (38), the washers (39) and (44), the nut (45) and the spacer (41) from the clips (40), (42) and (43) at position K.
END OF POST SBE 79-0088
PRE SBE 72-0189
(6) Make a note of the position of the spacer (50). Remove the bolt (46), the washer (47), and the spacer (50) from the clips (48), (49) and (51) at position L.
(7) Remove the bolt (52) and the washer (53) from the clip (54) at position M.
END OF PRE SBE 72-0189
POST SBE 72-0189 and PRE SBE 79-0088
(8) Make a note of the position of the spacer (129). Remove the bolt (127) and the spacer (129) from the clip (128) at position AB.
END OF POST SBE 72-0189 and END OF PRE SBE 79-0088
POST SBE 79-0088
(9) Make a note of the position of the spacer (129). Remove the bolt (127), the washer (130) and the spacer (129) from the clip (128) at position AB.
END OF POST SBE 79-0088
POST SBE 72-0189, PRE SBE 79-0088 and POST SBE 79-0088
(10) Remove the bolt (123), the washer (124) and the nut (126) from the clip (125) at position AA.
END OF POST SBE 72-0189, END OF PRE SBE 79-0088 and END OF POST SBE 79-0088
PRE SBE 72-0189
(11) Make a note of the position of the spacer (58). Remove the bolt (55), the washer (56), the nut (59) and the spacer (58) from the clip (57) at position N.
END OF PRE SBE 72-0189
POST SBE 72-0189 and PRE SBE 79-0088
(12) Make a note of the position of the spacers (58) and (61). Remove the bolt (55), the nut (59) and the spacers (58) and (61) from the clips (57) and (60) at position N.
END OF POST SBE 72-0189 and END OF PRE SBE 79-0088
POST SBE 79-0088
(13) Make a note of the position of the spacers (58) and (61). Remove the bolt (55), the washer (56), the nut (59) and the spacers (58) and (61) from the clips (57) and (60) at position N.
END OF POST SBE 79-0088
(14) Remove the bolt (64) and the washer (63) from the clip (62) at position P.
(15) Remove the bolt (65) and the washer (66) from the clip (67) at position Q.
(16) Remove the bolt (68), the washers (69) and (72) and the nut (73) from the clips (70) and (71) at position R.
PRE SBE 72-0189 and POST SBE 79-0088
(17) Remove the bolt (74), the washers (75) and (78) and the nut (79) from the clips (76) and (77) at position S.
END OF PRE SBE 72-0189 and END OF POST SBE 79-0088
POST SBE 72-0189 and PRE SBE 79-0088
(18) Remove the bolt (74) and the nut (79) from the clips (76) and (77) at position S.
END OF POST SBE 72-0189 and END OF PRE SBE 79-0088
PRE SBE 72-0189
(19) Remove the bolt (80), the washers (81) and (84) and the nut (85) from the clips (82) and (83) at position T.
END OF PRE SBE 72-0189
POST SBE 72-0189 and PRE SBE 79-0088
(20) Make a note of the position of the spacer (86). Remove the bolt (80), the nut (85) and the spacer (86) from the clips (82) and (83) at position T.
END OF POST SBE 72-0189 and END OF PRE SBE 79-0088
POST SBE 79-0088
(21) Make a note of the position of the spacer (86). Remove the bolt (80), the washers (81) and (84), the nut (85) and the spacer (86) from the clips (82) and (83) at position T.
END OF POST SBE 79-0088
PRE SBE 72-0189
(22) Remove the bolt (87), the washers (88) and (91) and the nut (92) from the clips (89) and (90) at position U.
(23) Make a note of the position of the spacer (97). Remove the bolt (100), the washers (94) and (99), the nut (93) and the spacer (97) from the clips (95),(96) and (98) at position V.
END OF PRE SBE 72-0189
POST SBE 72-0189 and PRE SBE 79-0088
(24) Make a note of the position of the spacer (103). Remove the bolt (101) and the spacer (103) from the clip (102) at position W.
(25) Remove the bolt (104) and the nut (107) from the clips (105) and (106) at position X.
END OF POST SBE 72-0189 and END OF PRE SBE 79-0088
POST SBE 72-0189 and PRE SBE 75-0081
(26) Remove the bolt (108) and the nut (111) from the clips (109) and (110) at position Y.
END OF POST SBE 72-0189 and END OF PRE SBE 75-0081
POST SBE 72-0189 and PRE SBE 79-0088
(27) Make a note of the position of the spacer (114). Remove the bolt (112), the nut (116) and the spacer (114) from the clips (113) and (115) at position Z.
END OF POST SBE 72-0189 and END OF PRE SBE 79-0088
POST SBE 79-0088
(28) Remove the bolt (131), the washers (132) and (135) and the nut (136) from the clips (133) and (134) at position AC.
END OF POST SBE 79-0088
E. Removal of the Core Engine Part of the Harness through the Bifurcation Panel
(1) Remove the four bolts (137) and the four nuts (138) from the bifurcation panel.
(2) Remove the two flame trap brackets (139).
(3) Remove the core engine part of the harness through the bifurcation panel.
Subtask 71-51-44-020-062-A ** ON A/C NOT FOR ALL (1) Remove the four bolts (137) and the four nuts (138) from the bifurcation panel.
(2) Remove the two flame trap brackets (139).
(3) Remove the core engine part of the harness through the bifurcation panel.
F. Removal of the Ignition Supply Harness from the Engine
(1) Remove the harness from the clips (3), (7), (11) and (15) at positions A, B, C and D.
PRE SBE 79-0088
(2) Remove the harness from the clips (20), (26) and (31) at positions F, G and H.
END OF PRE SBE 79-0088
POST SBE 79-0088
(3) Remove the harness from the clips (35) and (43) at positions J and K.
END OF POST SBE 79-0088
PRE SBE 72-0189
(4) Remove the harness from the clips (48) and (54) at positions L and M.
END OF PRE SBE 72-0189
POST SBE 72-0189
(5) Remove the harness from the clips (125) and (128) at positions AA and AB.
END OF POST SBE 72-0189
(6) Remove the harness from the clips (57) and (62) at positions N and P.
(7) Remove the harness from the clips (67) and (70) at positions Q and R.
(8) Remove the harness from the clips (77) and (82) at positions S and T.
PRE SBE 72-0189
(9) Remove the harness from the clips (90) and (98) at positions U and V.
END OF PRE SBE 72-0189
POST SBE 72-0189 and PRE SBE 79-0088
(10) Remove the harness from the clips (102) and (106) at positions W and X.
END OF POST SBE 72-0189 and END OF PRE SBE 79-0088
POST SBE 72-0189 and PRE SBE 75-0081
(11) Remove the harness from the clip (110) at position Y.
END OF POST SBE 72-0189 and END OF PRE SBE 75-0081
POST SBE 72-0189 and PRE SBE 79-0088
(12) Remove the harness from the clip (115) at position Z.
END OF POST SBE 72-0189 and END OF PRE SBE 79-0088
POST SBE 79-0088
(13) Remove the harness from the clip (134) at position AC.
END OF POST SBE 79-0088
(14) Remove the ignition supply harness from the engine.
Subtask 71-51-44-010-069-A ** ON A/C NOT FOR ALL (1) Remove the harness from the clips (3), (7), (11) and (15) at positions A, B, C and D.
PRE SBE 79-0088
(2) Remove the harness from the clips (20), (26) and (31) at positions F, G and H.
END OF PRE SBE 79-0088
POST SBE 79-0088
(3) Remove the harness from the clips (35) and (43) at positions J and K.
END OF POST SBE 79-0088
PRE SBE 72-0189
(4) Remove the harness from the clips (48) and (54) at positions L and M.
END OF PRE SBE 72-0189
POST SBE 72-0189
(5) Remove the harness from the clips (125) and (128) at positions AA and AB.
END OF POST SBE 72-0189
(6) Remove the harness from the clips (57) and (62) at positions N and P.
(7) Remove the harness from the clips (67) and (70) at positions Q and R.
(8) Remove the harness from the clips (77) and (82) at positions S and T.
PRE SBE 72-0189
(9) Remove the harness from the clips (90) and (98) at positions U and V.
END OF PRE SBE 72-0189
POST SBE 72-0189 and PRE SBE 79-0088
(10) Remove the harness from the clips (102) and (106) at positions W and X.
END OF POST SBE 72-0189 and END OF PRE SBE 79-0088
POST SBE 72-0189 and PRE SBE 75-0081
(11) Remove the harness from the clip (110) at position Y.
END OF POST SBE 72-0189 and END OF PRE SBE 75-0081
POST SBE 72-0189 and PRE SBE 79-0088
(12) Remove the harness from the clip (115) at position Z.
END OF POST SBE 72-0189 and END OF PRE SBE 79-0088
POST SBE 79-0088
(13) Remove the harness from the clip (134) at position AC.
END OF POST SBE 79-0088
(14) Remove the ignition supply harness from the engine.
G. Transferable Parts Removal
(1) Remove all the clips from the ignition supply harness at positions A, B, C and D.
PRE SBE 79-0088
(2) Remove all the clips from the ignition supply harness at positions F, G and H.
END OF PRE SBE 79-0088
POST SBE 79-0088
(3) Remove all the clips from the ignition supply harness at positions J and K.
END OF POST SBE 79-0088
PRE SBE 72-0189
(4) Remove all the clips from the ignition supply harness at positions L and M.
END OF PRE SBE 72-0189
POST SBE 72-0189
(5) Remove all the clips from the ignition supply harness at positions AA and AB.
END OF POST SBE 72-0189
(6) Remove all the clips from the ignition supply harness at positions N and P.
(7) Remove all the clips from the ignition supply harness at positions Q, R, S and T.
PRE SBE 72-0189
(8) Remove all the clips from the ignition supply harness at positions U and V.
END OF PRE SBE 72-0189
POST SBE 72-0189 and PRE SBE 79-0088
(9) Remove all the clips from the ignition supply harness at positions W and X.
END OF POST SBE 72-0189 and END OF PRE SBE 79-0088
POST SBE 72-0189 and PRE SBE 75-0081
(10) Remove all the clips from the ignition supply harness at position Y.
END OF POST SBE 72-0189 and END OF PRE SBE 75-0081
POST SBE 72-0189 and PRE SBE 79-0088
(11) Remove all the clips from the ignition supply harness at position Z.
END OF POST SBE 72-0189 and END OF PRE SBE 79-0088
POST SBE 79-0088
(12) Remove all the clips from the ignition supply harness at position AC.
END OF POST SBE 79-0088
(1) Remove all the clips from the ignition supply harness at positions A, B, C and D.
PRE SBE 79-0088
(2) Remove all the clips from the ignition supply harness at positions F, G and H.
END OF PRE SBE 79-0088
POST SBE 79-0088
(3) Remove all the clips from the ignition supply harness at positions J and K.
END OF POST SBE 79-0088
PRE SBE 72-0189
(4) Remove all the clips from the ignition supply harness at positions L and M.
END OF PRE SBE 72-0189
POST SBE 72-0189
(5) Remove all the clips from the ignition supply harness at positions AA and AB.
END OF POST SBE 72-0189
(6) Remove all the clips from the ignition supply harness at positions N and P.
(7) Remove all the clips from the ignition supply harness at positions Q, R, S and T.
PRE SBE 72-0189
(8) Remove all the clips from the ignition supply harness at positions U and V.
END OF PRE SBE 72-0189
POST SBE 72-0189 and PRE SBE 79-0088
(9) Remove all the clips from the ignition supply harness at positions W and X.
END OF POST SBE 72-0189 and END OF PRE SBE 79-0088
POST SBE 72-0189 and PRE SBE 75-0081
(10) Remove all the clips from the ignition supply harness at position Y.
END OF POST SBE 72-0189 and END OF PRE SBE 75-0081
POST SBE 72-0189 and PRE SBE 79-0088
(11) Remove all the clips from the ignition supply harness at position Z.
END OF POST SBE 72-0189 and END OF PRE SBE 79-0088
POST SBE 79-0088
(12) Remove all the clips from the ignition supply harness at position AC.
END OF POST SBE 79-0088