Special Detailed Inspection (US and HFEC) of Outer Wing, Pylon Forward Attachment Fittings

TASK 57-26-00-220-001-A
Special Detailed Inspection (US and HFEC) of Outer Wing, Pylon Forward Attachment Fittings

WARNING: BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

ZONE: 521
ZONE: 621

1. Reason for the Job
Refer to the MPD TASK: 572654-01

NOTE: The effectivity of this task is ALL. To know if this task is applicable for your aircraft, refer to the MPD task applicability and the weight variant data given in the SRM introduction.

2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 3M (10 FT)
No specific	AR	WARNING NOTICE(S)

B. Consumable Materials

REFERENCE	DESIGNATION
(Material No.08BAA9)	Non Aqueous Cleaner-General - -
(Material No.14SBA1)	Textile-Lint free Cotton -

C. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
521	INBOARD FIXED L.E STRUCTURE
621	INBOARD FIXED L.E STRUCTURE

D. Referenced Information

REFERENCE	DESIGNATION
TASK 54-51-17-000-001-A	Removal of the Pylon-to-Wing Forward Attach-Fitting at RIB4
TASK 54-51-17-000-804-A	Removal of the Pylon-to-Wing Forward Attach-Fitting at RIB5
TASK 54-51-17-400-001-A	Installation of the Pylon-to-Wing Forward Attach-Fitting at RIB4
TASK 54-51-17-400-804-A	Installation of the Pylon-to-Wing Forward Attach-Fitting at RIB5
NTM 572654
SRM 57260000	(for corrective action)
Outer Wing Pylon - Forward Attachment Fittings

3. Job Set-up
Subtask 57-26-00-941-051-A

A. Safety Precautions
(1) Put the WARNING NOTICE(S) in the cockpit to tell persons not to start the engine 1(2).

Subtask 57-26-00-010-051-A ** ON A/C NOT FOR ALL

B. Get Access
(1) Put the ACCESS PLATFORM 3M (10 FT) below the applicable pylon, zone 521(621).
(2) Remove the pylon-to-wing forward attachment fitting (Ref. AMM TASK 54-51-17-000-001).

Subtask 57-26-00-010-051-C ** ON A/C NOT FOR ALL

B. Get Access
(1) Put the ACCESS PLATFORM 3M (10 FT) below the applicable pylon, zone 521(621).
(2) Remove the pylon-to-wing forward attachment fitting (Ref. AMM TASK 54-51-17-000-804).

4. Procedure
Subtask 57-26-00-110-051-A

A. Preparation for Inspection
(1) Use a Textile-Lint free Cotton - (Material No.14SBA1) , made moist with Non Aqueous Cleaner-General - - (Material No.08BAA9) to clean the forward attachment fitting of the outer wing pylon, inboard and outboard.

Subtask 57-26-00-280-050-A

B. Special Detailed Inspection (US and HFEC) of Outer-Wing Pylon Forward-Attachment-Fittings
(1) Do a special detailed inspection of the forward attachment fitting of the outer wing pylon, inboard and outboard NTM 572654.

NOTE: If necessary, refer to the SRM 57260000 for the correct repair procedure. If the defect is not included in this repair, you must request a procedure from AIRBUS.

5. Close-up
Subtask 57-26-00-410-052-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the pylon-to-wing forward attachment fitting (Ref. AMM TASK 54-51-17-400-001).

Subtask 57-26-00-410-052-C ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the pylon-to-wing forward attachment fitting (Ref. AMM TASK 54-51-17-400-804).

Subtask 57-26-00-942-052-A

B. Removal of Equipment
(1) Remove the WARNING NOTICE(S).
(2) Remove the access platform(s).
(3) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

[Rev.8 from Aug 2017] 2026.04.01 02:11:24 UTC