W DOC AIRBUS | AMM A320F

Removal of the Elevator Hinge-Arm End-Fittings

TASK 55-16-42-000-001-A
Removal of the Elevator Hinge-Arm End-Fittings

WARNING: MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS SURFACES ARE CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.
WARNING: MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS SURFACES ARE CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.
WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:
  • THE FLIGHT CONTROLS
  • THE FLIGHT CONTROL SURFACES
  • THE LANDING GEAR AND THE RELATED DOORS
  • COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.
WARNING: YOU MUST PUT ON AND ATTACH A SAFETY HARNESS BEFORE YOU START WORK:
  • ON THE THS OR IN THE REAR FUSELAGE
  • ON TOP OF THE WINGS OR PYLONS.
WITHOUT A SAFETY HARNESS, YOU CAN FALL. THIS CAN KILL YOU OR CAUSE YOU INJURY.
WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.
CAUTION: DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF CARBONFIBER REINFORCED PLASTIC.
1. Reason for the Job
To inspect or to replace the hinge arm fittings
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
AR
ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE
No specific
AR
SAFETY CLIP - CIRCUIT BREAKER
No specific
AR
WARNING NOTICE(S)
98D27903500000
2
PIN-SIDE STICK LOCKING
 B. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
334BB, 334DB, 334FB, 334HB, 335AB, 335BB, 335CB, 335DB, 344BB, 344DB, 344FB, 344HB, 345AB, 345BB, 345CB, 345DB
 C. Referenced Information
REFERENCE
DESIGNATION
TASK 29-10-00-864-001-A
Depressurize the Green Hydraulic System
TASK 29-10-00-864-002-A
Depressurize the Yellow Hydraulic System
TASK 29-10-00-864-003-A
Depressurize the Blue Hydraulic System
TASK 55-13-11-000-001-A
Remove/Open of the Trimmable Horizontal Stabilizer (THS) Trailing-Edge Access-Panels
TASK 55-16-48-000-001-A
Removal of the Elevator Support Struts
TASK 55-22-11-000-001-A
Removal of the Elevator Leading Edge Access Panels 335AB (345AB), 335BB (345BB), 335CB (345CB), 335DB (345DB).
F Elevator Hinge Arm End Fittings
F Elevator Hinge Arm End Fittings
3. Job Set-up
Subtask 55-16-42-860-050-A
A. Depressurize Hydraulic Systems
   (1) Depressurize the Green, Yellow and Blue hydraulic systems (Ref. AMM TASK 29-10-00-864-001) (Ref. AMM TASK 29-10-00-864-002) (Ref. AMM TASK 29-10-00-864-003).
Subtask 55-16-42-865-051-A
B. Open, safety and tag this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
49VUFLIGHT CONTROLS/ELAC1/NORM/SPLY15CE1B11
49VUFLIGHT CONTROLS/THS/ACTR/MOT219CE2B09
** ON A/C NOT FOR ALL
49VUFLIGHT CONTROLS/ELAC1/NORM/SPLY15CE1B06
49VUFLIGHT CONTROLS/THS/ACTR/MOT219CE2B04
** ON A/C ALL
105VUFLIGHT CONTROLS/ELAC2/STBY SPLY16CE2A02
105VUFLT CTL/ELAC1/STBY SPLY16CE1A01
121VUFLIGHT CONTROLS/THS ACTR/MOT319CE3Q17
121VUFLIGHT CONTROLS/THS ACTR/MOT119CE1Q16
121VUFLIGHT CONTROLS/ELAC2/NORM/SPLY15CE2R20
Subtask 55-16-42-481-050-A
C. Install Locking Devices
   (1) Put the 98D27903500000 PIN-SIDE STICK LOCKING in the CAPT and F/O side stick controllers.
Subtask 55-16-42-941-050-A
D. Safety Precautions
   (1) Put the WARNING NOTICE(S) in the flight compartment to tell persons not to operate the flight controls.
   (2) Put the WARNING NOTICE(S) in position to tell persons not to operate the hydraulic systems.
   (3) Put the ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE in position at zone 334 for the left hand elevator hinge arm fittings and/or zone 344 for the right hand elevator hinge arm fittings.
Subtask 55-16-42-010-050-A
E. Get Access
   (1) Open the THS Trailing Edge Access Panels 334BB ( 344BB), 334DB ( 344DB), 334FB ( 344FB), 334HB ( 344HB), as necessary (Ref. AMM TASK 55-13-11-000-001).
   (2) Remove the Elevator Leading Edge Access Panels 335AB ( 345AB), 335BB ( 345BB), 335CB ( 345CB), 335DB ( 345DB), as necessary (Ref. AMM TASK 55-22-11-000-001).
Hinge Arm Fitting Number
THS Panel(s)
Elevator Panel(s)
1
334BB (344BB)
335AB (345AB)
2
334DB (344DB)
335BB (345BB)
3
334DB (344DB)
335BB (345BB)
4
334DB (344DB)
335BB (345BB)
5
334FB (344FB)
335CB (345CB)
6
334HB (344HB)
335DB (345DB)
4. Procedure
Subtask 55-16-42-020-051-B
A. Removal of Hinge-Arm End Fittings 1, 2, 3, 5 and 6
   (1) Disconnect the hinge-arm end fitting (9) from the applicable attachment fitting (1).
     (a) Remove and discard the cotter pin (12).
     (b) Remove the nut (11).
     (c) Remove and discard the cotter pin (2).
     (d) Remove the bolt (4) and the bushes (3) from the hinge support.
   (2) Remove and discard the cotter pin (10).
   (3) Remove the nuts (7), the washers (8) and the bolts (5).
   (4) Record the position of the bolts (5).
NOTE: The bolts (5) have different lengths and some of them attach a bonding strap.
   (5) Remove the hinge-arm end fitting (9) from the hinge arm (6).
Subtask 55-16-42-020-055-B
B. Removal of Hinge-Arm End Fitting No. 4
   (1) Disconnect the elevator support strut (18) (Ref. AMM TASK 55-16-48-000-001).
   (2) Disconnect the hinge-arm end fitting (23) from the attachment fitting (16).
     (a) Remove the sleeve (17).
     (b) Remove and discard the cotter pin (15).
     (c) Remove the bolt (13) and the bush (14) from the hinge support.
   (3) Remove and discard the cotter pin (24).
   (4) Remove the nuts (21), the washers (22) and the bolts (19).
   (5) Record the position of the bolts (19).
NOTE: The bolts (19) have different lengths and some of them attach a bonding strap.
   (6) Remove the hinge-arm end fitting (23) from the hinge arm (20).
[Rev.10 from 2021] 2026.04.01 02:05:13 UTC
"Aviabrain" 2025