W DOC AIRBUS | AMM A320F

Removal of the Belly Fairing Access Panels

TASK 53-35-13-000-001-A
Removal of the Belly Fairing Access Panels

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:
  • THE FLIGHT CONTROLS
  • THE FLIGHT CONTROL SURFACES
  • THE LANDING GEAR AND THE RELATED DOORS
  • COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.
NOTE: The removal procedure for one panel is given. The procedure is almost the same for all panels.
NOTE: A minimum of two persons are necessary to do this procedure.
ZONE: 190
ZONE: 734
ZONE: 744
1. Reason for the Job
Self explanatory
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
1
ACCESS PLATFORM 2M (6 FT)
No specific
AR
CAP - BLANKING
No specific
1
WARNING NOTICE(S)
98D27803000000
1
LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION
 B. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
190
BELLY FAIR, AIR CONDITIONING & HYD COMPT
734
MAIN DOOR
744
MAIN DOOR
147AB, 147BB, 147EB, 147FB, 148FB, 191GB, 191JB, 195CB, 197AB, 197GB
198KB
198BB
198MB, 826CR, 826DR
198GB
 C. Referenced Information
REFERENCE
DESIGNATION
TASK 29-22-00-860-007-A
Installation of the Safety Device of the Ram Air Turbine
TASK 32-12-00-010-001-A
Open the Main Gear Doors for Access
TASK 33-48-12-000-001-A
Removal of the Lower Beacon/Strobe Light from the Fuselage Outside
F Access Panels - Left Belly Fairing ** ON A/C NOT FOR ALL
F Access Panels - Right Belly Fairing ** ON A/C NOT FOR ALL
F Belly Fairing Access Panels - Typical Installation ** ON A/C NOT FOR ALL
F Belly Fairing Access Panels - Typical Installation ** ON A/C NOT FOR ALL
F Access Panels - Left Belly Fairing ** ON A/C NOT FOR ALL
F Access Panels - Right Belly Fairing ** ON A/C NOT FOR ALL
F Belly Fairing Access Panels - Typical Installation ** ON A/C NOT FOR ALL
F Access Panels - Left Belly Fairing ** ON A/C NOT FOR ALL
F Access Panels - Right Belly Fairing ** ON A/C NOT FOR ALL
F Belly Fairing Access Panels - Typical Installation ** ON A/C NOT FOR ALL
F Access Panels - Left Belly Fairing ** ON A/C NOT FOR ALL
F Access Panels - Right Belly Fairing ** ON A/C NOT FOR ALL
3. Job Set-up
Subtask 53-35-13-010-050-A
A. Get Access
   (1) Install the 98D27803000000 LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION on the flap/slat control lever.
   (2) Put the WARNING NOTICE(S) on the flap/slat control lever to tell persons not to operate the flaps or slats.
   (3) If necessary, open the MLG doors (Ref. AMM TASK 32-12-00-010-001).
   (4) Put the ACCESS PLATFORM 2M (6 FT) in position below the applicable access panel.
   (5) Install the Ram Air Turbine (RAT) safety device (Ref. AMM TASK 29-22-00-860-007).
4. Procedure
Subtask 53-35-13-020-050-A ** ON A/C NOT FOR ALL
A. Removal of Access Panels 147AB, 147BB, 147EB, 147FB, 148FB, 191GB, 191JB, 195CB, 197AB, 197GB, 198BB and 198GB
NOTE: It is necessary to record the location of each fastener and each bonding point during the removal procedure. This will make the installation procedure easier.
   (1) Hold the panel (3) and remove the screws (1) and the washers (2).
   (2) Record the position of the screws (1).
NOTE: This will make the installation procedure easier.
   (3) For access panel 191JB:
     (a) Disconnect the electrical connector from anti-collision light 6LV (Ref. AMM TASK 33-48-12-000-001).
     (b) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
     (c) Remove the bonding strap from anti-collision light 6LV.
   (4) Remove the panel (3).
   (5) Record the location of the bonding points on the removed panel (3).
NOTE: The bonding points have a rough surface, no protection, and a diameter of 20 mm (0.7874 in.).
Subtask 53-35-13-020-050-C ** ON A/C NOT FOR ALL
A. Removal of Access Panels 147AB, 147BB, 147EB, 147FB, 148FB, 191GB, 191JB, 195CB, 197AB, 197GB, 198BB, 198MB, 826CR and 826DR
   (1) Hold the panel (3) and remove the screws (1) and the washers (2).
   (2) Record the position of the screws (1).
NOTE: This will make the installation procedure easier.
   (3) For access panel 191JB:
     (a) Disconnect the electrical connector from anti-collision light 6LV (Ref. AMM TASK 33-48-12-000-001).
     (b) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
     (c) Remove the bonding strap from anti-collision light 6LV.
   (4) Remove the panel (3).
   (5) Record the location of the bonding points on the removed panel (3).
NOTE: The bonding points have a rough surface, no protection, and a diameter of 20 mm (0.7874 in.).
Subtask 53-35-13-020-050-G ** ON A/C NOT FOR ALL
A. Removal of Access Panels 147AB, 147BB, 147EB, 147FB, 148FB, 191GB, 191JB, 195CB, 197AB, 197GB, 198KB and 198GB
NOTE: It is necessary to record the location of each fastener and each bonding point during the removal procedure. This will make the installation procedure easier.
   (1) Hold the panel (3) and remove the screws (1) and the washers (2).
   (2) Record the position of the screws (1).
NOTE: This will make the installation procedure easier.
   (3) For access panel 191JB:
     (a) Disconnect the electrical connector from anti-collision light 6LV (Ref. AMM TASK 33-48-12-000-001).
     (b) Put the CAP-BLANKING on each disconnected electrical connector and receptacle.
     (c) Remove the bonding strap from anti-collision light 6LV.
   (4) Remove the panel (3).
   (5) Record the location of the bonding points on the removed panel (3).
NOTE: The bonding points have a rough surface, no protection, and a diameter of 20 mm (0.7874 in.).
[Rev.10 from 2021] 2026.04.01 03:46:54 UTC
"Aviabrain" 2025