DOC AIRBUS | AMM A320FDetailed Inspection of Locking Hooks and Fork Fittings of AFT Cargo Compartment Door at all Frames, Between Longeron 4 and Longeron 5 (6 Places)
TASK 52-32-11-200-006-A
Detailed Inspection of Locking Hooks and Fork Fittings of AFT Cargo Compartment Door at all Frames, Between Longeron 4 and Longeron 5 (6 Places)
Refer to the MPD TASK: 523119-01
DETAILED INSPECTION OF LOCKING HOOKS AND FORK FITTINGS OF AFT CARGO COMPARTMENT DOOR AT ALL FRAMES, BETWEEN LONGERON 4 AND LONGERON 5 (6 PLACES)
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Work Zones and Access Panels
D. Referenced Information
3. Job Set-up
Subtask 52-32-11-010-055-A ** ON A/C NOT FOR ALL
Subtask 52-32-11-615-051-A ** ON A/C NOT FOR ALL
Subtask 52-32-11-865-061-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 01:42:09 UTC
Detailed Inspection of Locking Hooks and Fork Fittings of AFT Cargo Compartment Door at all Frames, Between Longeron 4 and Longeron 5 (6 Places)
WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
ZONE: 826
1. Reason for the JobRefer to the MPD TASK: 523119-01
DETAILED INSPECTION OF LOCKING HOOKS AND FORK FITTINGS OF AFT CARGO COMPARTMENT DOOR AT ALL FRAMES, BETWEEN LONGERON 4 AND LONGERON 5 (6 PLACES)
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE |
| No specific | AR | SAFETY CLIP - CIRCUIT BREAKER |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.05RDA1) | Adhesive Film Tape-Masking - - |
| (Material No.08BAA9) | Non Aqueous Cleaner-General - - |
| (Material No.12ABB1) | Corrosion Preventive Compound-Water Displacing Hard Film - |
| (Material No.12ABC1) | Corrosion Preventive Compound_Water Displacing Soft Film - |
| (Material No.14SBA1) | Textile-Lint free Cotton - |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 826 | AFT CARGO COMPARTMENT DOOR |
| 826AR |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 51-73-11-300-002-A | Repair of Minor Damage on Titanium, Forged Aluminum, or Steel Components |
| TASK 51-75-12-300-001-A | Repair of Major Paint Damage on Light Alloy and Composite Material |
| TASK 51-78-00-916-001-A | Application of Temporary Protection System (TPS) |
| TASK 52-30-00-860-001-A | Open the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump |
| TASK 52-30-00-860-002-A | Close the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump |
| TASK 52-32-21-000-013-A | Removal of the Latching Unit |
| SRM 517300 | |
| SRM 517400 | |
| SRM 523000 | |
Inspection of the Latching Hooks with the Adjacent Cargo Door FrameSubtask 52-32-11-010-055-A ** ON A/C NOT FOR ALL
A. Get Access
(1) Remove the access panel 826AR to get access to the locking mechanism of the cargo door.
(2) Open the cargo door and safety it with the actuator safety locks (Ref. AMM TASK 52-30-00-860-001).
(3) Put the ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE in position below the opened cargo door.
Subtask 52-32-11-865-060-A ** ON A/C NOT FOR ALL (1) Remove the access panel 826AR to get access to the locking mechanism of the cargo door.
(2) Open the cargo door and safety it with the actuator safety locks (Ref. AMM TASK 52-30-00-860-001).
(3) Put the ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE in position below the opened cargo door.
B. Open, safety and tag this(these) circuit breaker(s):
4. Procedure| PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 121VU | HYDRAULIC/HYD POWER/Y | 3803GX | N30 |
| ** ON A/C NOT FOR ALL | |||
| 121VU | HYDRAULIC/HYD POWER/Y | 3803GX | N31 |
| ** ON A/C NOT FOR ALL | |||
| 122VU | DOORS/CARGO | 1MJ | T12 |
| 123VU | Y HYD/ELEC/PUMP | 3802GX | AB06 |
| 123VU | Y HYD/ELEC/ELEC PUMP/NORM | 3801GX | AB03 |
Subtask 52-32-11-615-051-A ** ON A/C NOT FOR ALL
A. Cleaning Procedure
(1) Make sure that the area for inspection is clean. If the inspection area is not clean:
(a) Clean the area with Non Aqueous Cleaner-General - - (Material No.08BAA9) and a Textile-Lint free Cotton - (Material No.14SBA1) .
(2) If there is a Temporary Protection System (TPS) layer applied that prevents the inspection of the area, remove the TPS layer (Ref. AMM TASK 51-78-00-916-001).
Subtask 52-32-11-210-056-B ** ON A/C NOT FOR ALL (1) Make sure that the area for inspection is clean. If the inspection area is not clean:
(a) Clean the area with Non Aqueous Cleaner-General - - (Material No.08BAA9) and a Textile-Lint free Cotton - (Material No.14SBA1) .
(2) If there is a Temporary Protection System (TPS) layer applied that prevents the inspection of the area, remove the TPS layer (Ref. AMM TASK 51-78-00-916-001).
B. Detailed Inspection of Locking Hooks and Fork Fittings of AFT Cargo Compartment Door at all Frames, Between Longeron 4 and Longeron 5 (6 Places)
(1) Examine the inner surface of each latching hook for wear, chafe marks and cracks.
(a) If you find marks, measure the depth of the damage:
(c) If the latching hook has marks with a depth of more than 0.3 mm (0.0118 in.), replace it (Ref. AMM TASK 52-32-21-000-013).
(d) If you find a crack, replace the latching hook (Ref. AMM TASK 52-32-21-000-013).
(2) Examine the fork fittings of each door frame and the adjacent skin area for scratches, marks, cracks and corrosion:
(a) If you find a scratch or a mark:
(c) If you find corrosion:
(3) Make sure that the paint coat of the fork fitting and the adjacent skin area is in the correct condition (Ref. AMM TASK 51-75-12-300-001).
Subtask 52-32-11-916-051-A ** ON A/C NOT FOR ALL (1) Examine the inner surface of each latching hook for wear, chafe marks and cracks.
(a) If you find marks, measure the depth of the damage:
- Marks up to a depth of 0.1 mm (0.0039 in.) are permitted.
(c) If the latching hook has marks with a depth of more than 0.3 mm (0.0118 in.), replace it (Ref. AMM TASK 52-32-21-000-013).
(d) If you find a crack, replace the latching hook (Ref. AMM TASK 52-32-21-000-013).
(2) Examine the fork fittings of each door frame and the adjacent skin area for scratches, marks, cracks and corrosion:
(a) If you find a scratch or a mark:
- find the limits of the damaged area SRM 523000
- remove the damage when it is less than the limit SRM 517300.
(c) If you find corrosion:
- find the limits of the corroded area SRM 523000
- remove the damage when it is less than the limit SRM 517400.
(3) Make sure that the paint coat of the fork fitting and the adjacent skin area is in the correct condition (Ref. AMM TASK 51-75-12-300-001).
C. Application of the Temporary Protection System (TPS)
(1) Apply Adhesive Film Tape-Masking - - (Material No.05RDA1) on the items adjacent to the area: the seals, bellows, door mechanisms, proximity switches and fittings.
(2) If there is a TPS layer, do a check of the condition of the TPS layer (Ref. AMM TASK 51-78-00-916-001).
(4) If, before the inspection:
5. Close-up(1) Apply Adhesive Film Tape-Masking - - (Material No.05RDA1) on the items adjacent to the area: the seals, bellows, door mechanisms, proximity switches and fittings.
(2) If there is a TPS layer, do a check of the condition of the TPS layer (Ref. AMM TASK 51-78-00-916-001).
NOTE: AIRBUS recommends that you always apply a new layer of TPS. This is to make sure that the TPS layer continues to give satisfactory corrosion protection. If you think that the TPS layer is in the correct condition, you can apply a new layer (as a spray) on the layer.
(3) If the TPS layer is damaged, remove the TPS layer and apply a new layer of Corrosion Preventive Compound_Water Displacing Soft Film - (Material No.12ABC1) or Corrosion Preventive Compound-Water Displacing Hard Film - (Material No.12ABB1) . (4) If, before the inspection:
- there was removal of the TPS layer
or - the inspection area was cleaned with high pressure water, steam, solvents and/or cleaning agents.
Subtask 52-32-11-865-061-A ** ON A/C NOT FOR ALL
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
Subtask 52-32-11-410-055-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 121VU | HYDRAULIC/HYD POWER/Y | 3803GX | N30 |
| ** ON A/C NOT FOR ALL | |||
| 121VU | HYDRAULIC/HYD POWER/Y | 3803GX | N31 |
| ** ON A/C NOT FOR ALL | |||
| 122VU | DOORS/CARGO | 1MJ | T12 |
| 123VU | Y HYD/ELEC/PUMP | 3802GX | AB06 |
| 123VU | Y HYD/ELEC/ELEC PUMP/NORM | 3801GX | AB03 |
B. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the access panel 826AR.
(3) Remove the actuator safety locks and close the cargo door (Ref. AMM TASK 52-30-00-860-002).
(4) Remove the access platform(s).
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Install the access panel 826AR.
(3) Remove the actuator safety locks and close the cargo door (Ref. AMM TASK 52-30-00-860-002).
(4) Remove the access platform(s).