Removal of the Safety Devices from the Landing Gear Doors

TASK 32-00-00-081-002-A
Removal of the Safety Devices from the Landing Gear Doors

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.

WARNING: MAKE SURE THAT THE WHEEL CHOCKS ARE IN POSITION. MOVEMENT OF THE AIRCRAFT CAN BE DANGEROUS.

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	SAFETY BARRIER(S)
No specific	AR	WARNING NOTICE(S)

B. Referenced Information

REFERENCE	DESIGNATION
TASK 32-12-00-010-001-A	Open the Main Gear Doors for Access
TASK 32-12-00-410-001-A	Close the Main Gear Doors after Access
TASK 32-22-00-010-001-A	Nose Gear Doors - Ground Doors Opening
TASK 32-22-00-410-001-A	Nose Gear Doors - Ground Doors Closing
Main and Nose Landing-Gear Doors Safety-Devices

3. Job Set-up
Subtask 32-00-00-941-062-A

A. Safety Precautions
(1) Make sure that the SAFETY BARRIER(S)S are in position.
(2) Make sure that there is a WARNING NOTICE(S) to tell persons not to operate:

the landing gear or
the landing gear doors.

(3) Make sure that the wheel chocks are correctly installed.

Subtask 32-00-00-010-056-A

B. Get Access
(1) Make sure that the applicable ground door-opening handle(s) is(are) set to 'open':

for the MLG doors (Ref. AMM TASK 32-12-00-010-001)
for the NLG doors (Ref. AMM TASK 32-22-00-010-001).

4. Procedure
Subtask 32-00-00-081-051-A

A. Removal of the Safety Devices from the Landing Gear Doors
(1) To remove the safety devices from the MLG doors:
(a) Remove the pins (1) from the DAH602734 SLEEVE-GROUND LOCK or the 460005835 SLEEVE - GROUND LOCK.
(b) Remove the DAH602734 SLEEVE-GROUND LOCK or the 460005835 SLEEVE - GROUND LOCK from each of the piston rods of the MLG door actuating cylinders.
(2) To remove the safety devices from the NLG doors:
(a) Remove the 98D32203502000 SAFETY PIN - NLG DOOR from the holes in each NLG door and hinge.

Subtask 32-00-00-410-051-A

B. Close the applicable landing gear door/s:

for the MLG doors (Ref. AMM TASK 32-12-00-410-001)
for the NLG doors (Ref. AMM TASK 32-22-00-410-001).

5. Close-up
Subtask 32-00-00-942-065-A

A. Removal of Equipment
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the safety barriers.
(3) Remove the WARNING NOTICE(S).
(4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

[Rev.10 from 2021] 2026.04.01 00:39:15 UTC