Removal of the Hydraulic Low-Pressure Switch Tube

TASK 29-11-49-000-005-A
Removal of the Hydraulic Low-Pressure Switch Tube

WARNING: OBEY THE HYDRAULIC SAFETY PROCEDURES.

WARNING: DO NOT TOUCH THE HYDRAULIC SYSTEM COMPONENTS FOR A SHORT TIME AFTER THE ENGINE IS SHUTDOWN. THE ENGINE COMPONENTS STAY HOT FOR SOME TIME AND CAN CAUSE INJURY.

CAUTION: DO NOT LET HYDRAULIC FLUID FALL ON THE ENGINE. UNWANTED HYDRAULIC FLUID MUST BE REMOVED IMMEDIATELY WITH A CLEAN LINT FREE CLOTH. THE FLUID CAN CAUSE DAMAGE TO THE SURFACE PROTECTION AND TO SOME PARTS.

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 1M (3 FT)-ADJUSTABLE
No specific	2	CONTAINER 10 L(2 1/2 USGAL)
No specific	AR	CONTAINER 5 L (1.32 USGAL)
No specific	AR	COVER - PROTECTION
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	AR	WARNING NOTICE(S)
No specific	1	WRENCH - STANDARD

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL

C. Referenced Information

REFERENCE	DESIGNATION
TASK 29-10-00-864-001-A	Depressurize the Green Hydraulic System
TASK 29-14-00-614-001-A	Depressurization of the Hydraulic Reservoirs
Hydraulic Low-Pressure Switch Tube
Hydraulic Low-Pressure Switch Hose/Tube Assembly
Hydraulic Low-Pressure Switch Hose Assembly
FOR [1000EM1] (ENGINE-1)
TASK 71-13-00-010-040-B	Opening of the Fan Cowl Doors

3. Job Set-up
Subtask 29-11-49-860-085-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Depressurize the Green hydraulic system (Ref. AMM TASK 29-10-00-864-001).
(2) Depressurize the Green hydraulic reservoir (Ref. AMM TASK 29-14-00-614-001).
(3) Put WARNING NOTICE(S) in position to tell persons not to pressurize the Green hydraulic system:

on the ground service panel 197CB.

(4) Put WARNING NOTICE(S) in position on the access door 195BB to tell persons not to pressurize the Green hydraulic reservoir.

Subtask 29-11-49-941-071-A ** ON A/C NOT FOR ALL

B. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:

put WARNING NOTICE(S) to tell persons not to start the engine.

(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) Put WARNING NOTICE(S) in position to tell persons not to pressurize the Green hydraulic system:

in the cockpit, on the HYD section of the overhead panel 40VU.

(4) On the overhead maintenance panel 50VU:

make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.

(5) Put WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).
(6) Put a CONTAINER 5 L (1.32 USGAL) below the hydraulic low-pressure switch tube.

Subtask 29-11-49-865-058-A ** ON A/C NOT FOR ALL

C. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
121VU	HYDRAULIC/G HYD/PUMP ENG1/MONG	1702GK	R34

Subtask 29-11-49-010-071-A ** ON A/C NOT FOR ALL

D. Get Access
(1) Open the left fan cowl door:
(a) FOR [1000EM1] (ENGINE-1)

open the door 437AL (Ref. AMM TASK 71-13-00-010-040).

(2) Put the ACCESS PLATFORM 1M (3 FT)-ADJUSTABLE in position at the engine.

4. Procedure
Subtask 29-11-49-020-067-A ** ON A/C NOT FOR ALL

A. Removal of the Hydraulic Low-Pressure Switch Tube

Hydraulic Low-Pressure Switch Tube ** ON A/C NOT FOR ALL

PRE SB RA32029-13
(1) Disconnect the low-pressure switch tube (15) from the pressure hose/tube and let the fluid flow into the CONTAINER 5 L (1.32 USGAL).

NOTE: Use a second WRENCH - STANDARD to hold the fitting on the pressure hose/tube when you loosen the coupling nut on the tube.

(2) Disconnect the low-pressure switch tube (15) from the hydraulic low-pressure switch.

NOTE: Use a second WRENCH - STANDARD to hold the pressure switch when you loosen the coupling nut on the tube.

(3) Remove the bolts (5) and the washers (10) that attach the clamps (20) to the channel. Remove the clamps (20) from the low-pressure switch tube (15).
(4) Remove the low-pressure switch tube (15) from the engine.
(5) Put COVER - PROTECTION on the low-pressure switch tube (15), the fitting on the pressure hose/tube and the hydraulic low-pressure switch.

END OF PRE SB RA32029-13

Subtask 29-11-49-020-087-A ** ON A/C NOT FOR ALL

B. Removal of the Hydraulic Low-Pressure Switch Tube

Hydraulic Low-Pressure Switch Hose/Tube Assembly ** ON A/C NOT FOR ALL

POST SB RA32029-13
(1) Disconnect the low-pressure switch hose/tube assembly (17) from the pressure hose/tube and let the fluid flow into the CONTAINER 10 L(2 1/2 USGAL).

NOTE: Use a second WRENCH - STANDARD to hold the fitting on the pressure hose/tube when you loosen the coupling nut on the tube.

(2) Disconnect the low-pressure switch hose/tube assembly (17) from the hydraulic low-pressure switch.

NOTE: Use a second WRENCH - STANDARD to hold the pressure switch when you loosen the coupling nut on the tube.

(3) Remove the bolt (7) and the washer (10) that attach the clamp (20) to the channel. Remove the clamp (20) from the low-pressure switch hose/tube assembly (17).
(4) Remove the bolts (7), the washers (10) and the nuts (25) that attach the clamps (20) to the channel. Remove the clamps (20) from the low-pressure switch hose/tube assembly (17).
(5) Remove the low-pressure switch hose/tube assembly (17).
(6) Put COVER - PROTECTION on the low-pressure switch hose/tube assembly (17), the fitting on the pressure hose/tube and the hydraulic low-pressure switch.

END OF POST SB RA32029-13

Subtask 29-11-49-020-123-A ** ON A/C NOT FOR ALL

C. Removal of the Hydraulic Low-Pressure Switch Tube

Hydraulic Low-Pressure Switch Hose Assembly ** ON A/C NOT FOR ALL

POST SB RA32029-15

POST SB RA32029-16

(1) Disconnect the low-pressure switch hose assembly (19) from the pressure hose/tube and let the fluid flow into the CONTAINER 10 L(2 1/2 USGAL).

NOTE: Use a second WRENCH - STANDARD to hold the fitting on the pressure hose/tube when you loosen the coupling nut on the tube.

(2) Disconnect the low-pressure switch hose assembly (19) from the hydraulic low-pressure switch.

NOTE: Use a second WRENCH - STANDARD to hold the pressure switch when you loosen the coupling nut on the tube.

(3) Remove the low-pressure switch hose assembly (19).
(4) Put COVER - PROTECTION on the low-pressure switch hose assembly (19), the fitting on the pressure hose/tube and the hydraulic low-pressure switch.

END OF POST SB RA32029-15

END OF POST SB RA32029-16

[Rev.10 from 2021] 2026.04.01 00:17:10 UTC