Removal of the Hydraulic Pressure Hose/Tube Assembly

TASK 29-11-49-000-002-A
Removal of the Hydraulic Pressure Hose/Tube Assembly

WARNING: OBEY THE HYDRAULIC SAFETY PROCEDURES.

WARNING: DO NOT TOUCH THE HYDRAULIC SYSTEM COMPONENTS FOR A SHORT TIME AFTER THE ENGINE IS SHUTDOWN. THE ENGINE COMPONENTS STAY HOT FOR SOME TIME AND CAN CAUSE INJURY.

CAUTION: DO NOT LET HYDRAULIC FLUID FALL ON THE ENGINE. UNWANTED HYDRAULIC FLUID MUST BE REMOVED IMMEDIATELY WITH A CLEAN LINT FREE CLOTH. THE FLUID CAN CAUSE DAMAGE TO THE SURFACE PROTECTION AND TO SOME PARTS.

1. Reason for the Job
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	1	ACCESS PLATFORM 1M (3 FT)-ADJUSTABLE
No specific	AR	CONTAINER 5 L (1.32 USGAL)
No specific	1	COVER - PROTECTION
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	AR	WARNING NOTICE(S)
No specific	1	WRENCH - STRAP

B. Work Zones and Access Panels

ZONE/ACCESS	ZONE DESCRIPTION
FOR [1000EM1] (ENGINE-1)
437AL

C. Referenced Information

REFERENCE	DESIGNATION
TASK 29-10-00-864-001-A	Depressurize the Green Hydraulic System
TASK 29-14-00-614-001-A	Depressurization of the Hydraulic Reservoirs
Hydraulic Pressure Hose/Tube Assembly
Hydraulic Pressure Hose/Tube Assembly
Hydraulic Pressure Hose/Tube Assembly
Installation of the Hydraulic Pressure Hose/Tube Assembly
FOR [1000EM1] (ENGINE-1)
TASK 71-13-00-010-040-B	Opening of the Fan Cowl Doors

3. Job Set-up
Subtask 29-11-49-860-065-A ** ON A/C NOT FOR ALL

A. Aircraft Maintenance Configuration
(1) Depressurize the Green hydraulic system (Ref. AMM TASK 29-10-00-864-001).
(2) Depressurize the Green hydraulic reservoir (Ref. AMM TASK 29-14-00-614-001).
(3) Put WARNING NOTICE(S) in position to tell persons not to pressurize the Green hydraulic system:

on the ground service panel 197CB.

(4) Put WARNING NOTICE(S) on the access door 195BB to tell persons not to pressurize the Green hydraulic reservoir.

Subtask 29-11-49-941-065-A ** ON A/C NOT FOR ALL

B. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:

put WARNING NOTICE(S) to tell persons not to start the engine.

(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) Put WARNING NOTICE(S) in position to tell persons not to pressurize the Green hydraulic system:

in the cockpit, on the HYD section of the overhead panel 40VU.

(4) On the overhead maintenance panel 50VU:

make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.

(5) Put WARNING NOTICE(S) to tell persons not to energize the FADEC 1(2).
(6) Put a CONTAINER 5 L (1.32 USGAL) below the suction-hose adapter connection to the hydraulic pump.

Subtask 29-11-49-865-053-A ** ON A/C NOT FOR ALL

C. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
121VU	HYDRAULIC/G HYD/PUMP ENG1/MONG	1702GK	R34

Subtask 29-11-49-010-065-A ** ON A/C NOT FOR ALL

D. Get Access
(1) Open the left fan cowl door:
(a) FOR [1000EM1] (ENGINE-1)
open the door 437AL (Ref. AMM TASK 71-13-00-010-040).
(2) Put an ACCESS PLATFORM 1M (3 FT)-ADJUSTABLE in position at the engine.

4. Procedure
Subtask 29-11-49-020-060-A ** ON A/C NOT FOR ALL

A. Removal of the Hydraulic Pressure Hose
(1) Disconnect the pressure hose/tube (20) from the union in the hydraulic pump and let the fluid flow into the container.

NOTE: Use a second WRENCH - STRAP to hold the union on the hydraulic pump when you loosen the coupling nut on the pressure hose/tube.

(2) Disconnect the pressure hose/tube (20) from the fluid disconnect panel at the top of the engine.
(3) Remove the bolt (5), the washer (10) and the clamp (15) that attach the pressure hose/tube (20) to the higher bracket.

PRE SB RA 32029-13
(4) Remove the bolt (5), the washer (10) and the clamp (15) that attach the pressure hose/tube (20) to the two channels.

END OF PRE SB RA 32029-13

POST SB RA 32029-13

PRE SB RA 32029-14
(5) Remove the bolts (5, 6, 7, 12), the washers (8, 10, 14) and the clamps (9, 15, 16) that attach the pressure hose/tube (20) to the two channels and the bracket on the engine flange.

END OF POST SB RA 32029-13

END OF PRE SB RA 32029-14

POST SB RA 32029-14

POST SB RA 32029-15

POST SB RA 32029-16

(6) Remove the bolts (6, 7, 12, 22), the washers (8, 14, 24) and the clamps (9, 16, 26) that attach the pressure hose/tube (20) to the two channels and the bracket on the engine flange.

END OF POST SB RA 32029-14

END OF POST SB RA 32029-15

END OF POST SB RA 32029-16

(7) Disconnect the pressure switch tube from the tee-fitting on the pressure hose/tube (20).

NOTE: Use a second WRENCH - STRAP to hold the wrenching flats of the tee-fitting when you to hold the wrenching flats of the tee-fitting when you loosen the coupling nut on the tube.

(8) Remove the bolt (5), the washer (10) and the clamp (15) that attach the pressure hose/tube (20) to the lower bracket.
(9) Remove the bolt (25), the washer (30) and the nut (35) from the band of the center mount clamp (40).
(10) Open the band of the clamp (40) and remove the pressure hose/tube (20) from the insert. Put the band on the insert and install the bolt (25), the washer (30) and the nut (35).
(11) Remove the pressure hose/tube (20) from the engine.
(12) Put COVER - PROTECTION on the tee-fitting and the ends of the pressure hose/tube (20), the union on the hydraulic pump, and the fitting on the fluid disconnect panel.

[Rev.10 from 2021] 2026.04.01 00:17:04 UTC