W DOC AIRBUS | AMM A320F

Dimensional Check of the Slat-To-Track Attachment Fittings, Tracks 5 Thru 12

TASK 27-84-62-200-001-A
Dimensional Check of the Slat-To-Track Attachment Fittings, Tracks 5 Thru 12

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:
  • THE FLIGHT CONTROLS
  • THE FLIGHT CONTROL SURFACES
  • THE LANDING GEAR AND THE RELATED DOORS
  • COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.
WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.
1. Reason for the Job
Self Explanatory
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
AR
SAFETY BARRIER(S)
No specific
AR
WARNING NOTICE(S)
 B. Consumable Materials
REFERENCE
DESIGNATION
(Material No.03GBD1)
Synthetic Oil base Grease-General Purpose Lithium Thickened -
 C. Referenced Information
REFERENCE
DESIGNATION
TASK 27-84-62-000-001-A
Removal of the Slat Tracks 5 thru 12
TASK 27-84-62-400-001-A
Installation of the Slat Tracks 5 thru 12
TASK 27-84-64-000-001-A
Removal of the No. 2 Slat
TASK 27-84-64-400-002-A
Installation of the No. 2 Slat
TASK 27-84-65-000-001-A
Removal of the No 3 Slat
TASK 27-84-65-400-002-A
Installation of the No 3 Slat
TASK 27-84-66-000-001-A
Removal of the No. 4 Slat
TASK 27-84-66-400-002-A
Installation of the No. 4 Slat
TASK 27-84-67-000-001-A
Removal of the No. 5 Slat
TASK 27-84-67-400-002-A
Installation of the No. 5 Slat
F Slat 2, Track 5 - Attachment Details ** ON A/C NOT FOR ALL
F Slat 2, Track 5 - Attachment Details ** ON A/C NOT FOR ALL
F Slat 2, Track 6 - Attachment Details
F Slat 3, Track 7 - Attachment Details
F Slat 3, Track 8 - Attachment Details
F Slat 4, Track 9 - Attachment Details
F Slat 4, Track 10 - Attachment Details
F Slat 5, Track 11 - Attachment Details ** ON A/C NOT FOR ALL
F Slat 5, Track 11 - Attachment Details ** ON A/C NOT FOR ALL
F Slat 5, Track 12 - Attachment Details
3. Job Set-up
Subtask 27-84-62-941-052-A
A. Safety Precautions
   (1) Put the SAFETY BARRIER(S) in position.
   (2) Put a WARNING NOTICE(S) in the cockpit to tell persons not to operate the slat controls.
Subtask 27-84-62-010-052-A
B. Get Access
   (1) Remove the applicable Slat:
   (2) Remove the applicable Slat track (Ref. AMM TASK 27-84-62-000-001).
   (3) Make sure that the 98D27803500001 LOCKING TOOL ZERO POS or 98D27803500002 LOCKING TOOL ZERO POS is on the flap/slat control lever on panel 114VU.
   (4) For the Slat track 5, remove:
F Slat 2, Track 5 - Attachment Details ** ON A/C NOT FOR ALL
F Slat 2, Track 5 - Attachment Details ** ON A/C NOT FOR ALL
     (a) the nut (16), the locking plate (17), the nut (7), the washer (6), the bolt (15) and the eccentric bush (14).
     (b) the links (8) and (10) and the bolt (18).
NOTE: The bolts (1) and (19) and their related nuts and washers were removed when the Slat No. 2 was removed.
   (5) For the Slat track 6, remove:
F Slat 2, Track 6 - Attachment Details
     (a) the nuts (15), the washers (14), the bolts (18) and the two links (16).
     (b) the nut (21), the locking plate (19), the nut (13), the washer (12), the bolt (4) and the eccentric bush (5).
     (c) the links (9) and (11) and the bolt (20).
NOTE: The bolts (3) and their related nuts and washers were removed when the Slat No. 2 was removed.
   (6) For the Slat track 7, remove:
F Slat 3, Track 7 - Attachment Details
     (a) the nut (10), the locking plate (11), the nut (4), the washer (5), the bolt (15) and the eccentric bush (6).
     (b) the links (14) and (21) and the bolt (12).
NOTE: The bolts (3) and (16) and their related nuts and washers were removed when the Slat No. 3 was removed.
   (7) For the Slat track 8, remove:
F Slat 3, Track 8 - Attachment Details
     (a) the nuts (17), the washers (16), the bolts (20) and the two links (18).
     (b) the nut (9), the locking plate (10), the nut (15), the washer (14), the bolt (4) and the eccentric bush (5).
     (c) the links (13) and (21) and the bolt (11).
NOTE: The bolts (3) and their related nuts and washers were removed when the Slat No. 3 was removed.
   (8) For the Slat track 9, remove:
F Slat 4, Track 9 - Attachment Details
     (a) the nut (14), the locking plate (15), the nut (4), the washer (5), the bolt (13) and the eccentric bush (12).
     (b) the links (6) and (8) and the bolt (16).
NOTE: The bolts (1) and (17) and their related nuts and washers were removed when the Slat No. 4 was removed.
   (9) For the Slat track 10, remove:
F Slat 4, Track 10 - Attachment Details
     (a) the nuts (17), the washers (16), the bolts (20) and the two links (18).
     (b) the nut (9), the locking plate (10), the nut (15), the washer (14), the bolt (4) and the eccentric bush (5).
     (c) the links (13) and (21) and the bolt (11).
NOTE: The bolts (3) and their related nuts and washers were removed when the Slat No. 4 was removed.
   (10) For the Slat track 11, remove:
F Slat 5, Track 11 - Attachment Details ** ON A/C NOT FOR ALL
F Slat 5, Track 11 - Attachment Details ** ON A/C NOT FOR ALL
     (a) the nut (10), the locking plate (9), the nut (5), the washer (6), the bolt (12) and the eccentric bush (11).
     (b) the links (4) and (16) and the bolt (8).
NOTE: The bolts (1) and (20) and their related nuts and washers were removed when the Slat No. 5 was removed.
   (11) For the Slat track 12, remove:
F Slat 5, Track 12 - Attachment Details
     (a) the nut (11), the washer (10) and the bolt (30).
     (b) the nut (14), the washer (13), the bolt (29) and the links (8) and (31).
     (c) the nut (26), the locking plate (27), the nut (16), the washer (17), the bolt (25) and the eccentric bush (24).
     (d) the links (18) and (20) and the bolt (28).
NOTE: The bolts (5) and (6) and their related nuts and washers were removed when the Slat No. 5 was removed.
4. Procedure
Subtask 27-84-62-220-051-A
A. Dimensional Check of Slat 2, Track 5
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
B
12.666
12.684

12.639

OD 1
(0.4987)
(0.4994)

(0.4976)




0.0220
0.0580

0.1120

(0.0009)
(0.0023)

(0.0044)
B
12.706
12.724


12.751
ID 2
(0.5002)
(0.5009)


(0.5020)
Subtask 27-84-62-220-052-A
B. Dimensional Check of Slat 2, Track 5
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
B
12.666
12.684

12.653

OD 1
(0.4987)
(0.4994)

(0.4981)




0.0030
0.0340

0.0600

(0.0001)
(0.0013)

(0.0024)
B
12.687
12.700


12.713
ID 3
(0.4995)
(0.5000)


(0.5005)
Subtask 27-84-62-220-053-A
C. Dimensional Check of Slat 2, Track 5
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
15.966
15.984

15.943

OD 5
(0.6286)
(0.6293)

(0.6277)




0.0160
0.0520

0.0980

(0.0006)
(0.0020)

(0.0039)
C
16.000
16.018


16.041
ID 4
(0.6299)
(0.6306)


(0.6315)
Subtask 27-84-62-220-054-A
D. Dimensional Check of Slat 2, Track 5
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.640

OD 19
(0.4987)
(0.4994)

(0.4976)




0.0160
0.0610

0.1130

(0.0006)
(0.0024)

(0.0044)
C
12.700
12.727


12.753
ID 5
(0.5000)
(0.5011)


(0.5021)
Subtask 27-84-62-220-055-A
E. Dimensional Check of Slat 2, Track 5
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.653

OD 19
(0.4987)
(0.4994)

(0.4981)




0.0030
0.0340

0.0600

(0.0001)
(0.0013)

(0.0024)
C
12.687
12.700


12.713
ID 21
(0.4995)
(0.5000)


(0.5005)
Subtask 27-84-62-220-056-A
F. Dimensional Check of Slat 2, Track 5
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.643

OD 19
(0.4987)
(0.4994)

(0.4978)




0.0160
0.0520

0.0980

(0.0006)
(0.0020)

(0.0039)
C
12.700
12.718


12.741
ID 20
(0.5000)
(0.5007)


(0.5016)
Subtask 27-84-62-220-057-A
G. Dimensional Check of Slat 2, Track 5
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.639

OD 15
(0.4987)
(0.4994)

(0.4976)




0.0220
0.0580

0.1120

(0.0009)
(0.0023)

(0.0044)
C
12.706
12.724


12.751
ID 8
(0.5002)
(0.5009)


(0.5020)
Subtask 27-84-62-220-058-A
H. Dimensional Check of Slat 2, Track 5
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
15.836
15.854

15.820

OD 12
(0.6235)
(0.6242)

(0.6228)




0.0080
0.0390

0.0710

(0.0003)
(0.0015)

(0.0028)
C
15.862
15.875


15.891
ID 9
(0.6245)
(0.6250)


(0.6256)
Subtask 27-84-62-220-059-A
I. Dimensional Check of Slat 2, Track 5
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
18.959
18.980

18.927

OD 13
(0.7464)
(0.7472)

(0.7452)




0.0270
0.0690

0.1330

(0.0011)
(0.0027)

(0.0052)
C
19.007
19.028


19.060
ID 10
(0.7483)
(0.7491)


(0.7504)
Subtask 27-84-62-220-060-A
J. Dimensional Check of Slat 2, Track 5
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.643

OD 15
(0.4987)
(0.4994)

(0.4978)




0.0160
0.0520

0.0980

(0.0006)
(0.0020)

(0.0039)
C
12.700
12.718


12.741
ID 11
(0.5000)
(0.5007)


(0.5016)
Subtask 27-84-62-220-061-A
K. Dimensional Check of Slat 2, Track 6
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
B
12.666
12.684

12.639

OD 3
(0.4987)
(0.4994)

(0.4976)




0.0220
0.0580

0.1120

(0.0009)
(0.0023)

(0.0044)
B
12.706
12.724


12.751
ID 1
(0.5002)
(0.5009)


(0.5020)
Subtask 27-84-62-220-062-A
L. Dimensional Check of Slat 2, Track 6
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
B
12.666
12.684

12.653

OD 3
(0.4987)
(0.4994)

(0.4981)




0.0030
0.0340

0.0600

(0.0001)
(0.0013)

(0.0024)
B
12.687
12.700


12.713
ID 2
(0.4995)
(0.5000)


(0.5005)
Subtask 27-84-62-220-063-A
M. Dimensional Check of Slat 2, Track 6
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.639

OD 18
(0.4987)
(0.4994)

(0.4976)




0.0220
0.0580

0.1120

(0.0009)
(0.0023)

(0.0044)
C
12.706
12.724


12.751
ID 16
(0.5002)
(0.5009)


(0.5020)
Subtask 27-84-62-220-064-A
N. Dimensional Check of Slat 2, Track 6
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.653

OD 18
(0.4987)
(0.4994)

(0.4981)




0.0030
0.0340

0.0600

(0.0001)
(0.0013)

(0.0024)
C
12.687
12.700


12.713
ID 17
(0.4995)
(0.5000)


(0.5005)
Subtask 27-84-62-220-065-A
O. Dimensional Check of Slat 2, Track 6
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.639

OD 4
(0.4987)
(0.4994)

(0.4976)




0.0220
0.0580

0.1120

(0.0009)
(0.0023)

(0.0044)
C
12.706
12.724


12.751
ID 11
(0.5002)
(0.5009)


(0.5020)
Subtask 27-84-62-220-066-A
P. Dimensional Check of Slat 2, Track 6
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
15.836
15.854

15.820

OD 7
(0.6235)
(0.6242)

(0.6228)




0.0080
0.0390

0.0710

(0.0003)
(0.0015)

(0.0028)
C
15.862
15.875


15.891
ID 10
(0.6245)
(0.6250)


(0.6256)
Subtask 27-84-62-220-067-A
Q. Dimensional Check of Slat 2, Track 6
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
18.959
18.980

18.927

OD 6
(0.7464)
(0.7472)

(0.7452)




0.0270
0.0690

0.1330

(0.0011)
(0.0027)

(0.0052)
C
19.007
19.028


19.060
ID 9
(0.7483)
(0.7491)


(0.7504)
Subtask 27-84-62-220-068-A
R. Dimensional Check of Slat 2, Track 6
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.643

OD 4
(0.4987)
(0.4994)

(0.4978)




0.0160
0.0520

0.0980

(0.0006)
(0.0020)

(0.0039)
C
12.700
12.718


12.741
ID 8
(0.5000)
(0.5007)


(0.5016)
Subtask 27-84-62-220-069-A
S. Dimensional Check of Slat 3, Track 7
   (1) Fits and clearance dimensions.
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
B
12.666
12.684

12.639

OD 3
(0.4987)
(0.4994)

(0.4976)




0.0220
0.0580

0.1120

(0.0009)
(0.0023)

(0.0044)
B
12.706
12.724


12.751
ID 1
(0.5002)
(0.5009)


(0.5020)
Subtask 27-84-62-220-070-A
T. Dimensional Check of Slat 3, Track 7
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
B
12.666
12.684

12.653

OD 3
(0.4987)
(0.4994)

(0.4981)




0.0030
0.0340

0.0600

(0.0001)
(0.0013)

(0.0024)
B
12.687
12.700


12.713
ID 2
(0.4995)
(0.5000)


(0.5005)
Subtask 27-84-62-220-071-A
U. Dimensional Check of Slat 3, Track 7
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
15.966
15.984

15.943

OD 20
(0.6286)
(0.6293)

(0.6277)




0.0160
0.0520

0.0980

(0.0006)
(0.0020)

(0.0039)
C
16.000
16.018


16.041
ID 19
(0.6299)
(0.6306)


(0.6315)
Subtask 27-84-62-220-072-A
V. Dimensional Check of Slat 3, Track 7
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.640

OD 16
(0.4987)
(0.4994)

(0.4976)




0.0160
0.0610

0.1130

(0.0006)
(0.0024)

(0.0044)
C
12.700
12.727


12.753
ID 20
(0.5000)
(0.5011)


(0.5021)
Subtask 27-84-62-220-073-A
W. Dimensional Check of Slat 3, Track 7
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.653

OD 16
(0.4987)
(0.4994)

(0.4981)




0.0030
0.0340

0.0600

(0.0001)
(0.0013)

(0.0024)
C
12.687
12.700


12.713
ID 18
(0.4995)
(0.5000)


(0.5005)
Subtask 27-84-62-220-074-A
X. Dimensional Check of Slat 3, Track 7
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.643

OD 16
(0.4987)
(0.4994)

(0.4978)




0.0160
0.0520

0.0980

(0.0006)
(0.0020)

(0.0039)
C
12.700
12.718


12.741
ID 17
(0.5000)
(0.5007)


(0.5016)
Subtask 27-84-62-220-075-A
Y. Dimensional Check of Slat 3, Track 7
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.639

OD 15
(0.4987)
(0.4994)

(0.4976)




0.0220
0.0580

0.1120

(0.0009)
(0.0023)

(0.0044)
C
12.706
12.724


12.751
ID 14
(0.5002)
(0.5009)


(0.5020)
Subtask 27-84-62-220-076-A
Z. Dimensional Check of Slat 3, Track 7
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.643

OD 15
(0.4987)
(0.4994)

(0.4978)




0.0160
0.0520

0.0980

(0.0006)
(0.0020)

(0.0039)
C
12.700
12.718


12.741
ID 9
(0.5000)
(0.5007)


(0.5016)
Subtask 27-84-62-220-077-A
AA. Dimensional Check of Slat 3, Track 7
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
15.836
15.854

15.820

OD 8
(0.6235)
(0.6242)

(0.6228)




0.0080
0.0390

0.0710

(0.0003)
(0.0015)

(0.0028)
C
15.862
15.875


15.891
ID 13
(0.6245)
(0.6250)


(0.6256)
Subtask 27-84-62-220-078-A
AB. Dimensional Check of Slat 3, Track 7
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
18.959
18.980

18.927

OD 7
(0.7464)
(0.7472)

(0.7452)




0.0270
0.0690

0.1330

(0.0011)
(0.0027)

(0.0052)
C
19.007
19.028


19.060
ID 21
(0.7483)
(0.7491)


(0.7504)
Subtask 27-84-62-220-079-A
AC. Dimensional Check of Slat 3, Track 8
   (1) Fits and clearance dimensions.
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
B
12.666
12.684

12.639

OD 3
(0.4987)
(0.4994)

(0.4976)




0.0220
0.0580

0.1120

(0.0009)
(0.0023)

(0.0044)
B
12.706
12.724


12.751
ID 2
(0.5002)
(0.5009)


(0.5020)
Subtask 27-84-62-220-080-A
AD. Dimensional Check of Slat 3, Track 8
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
B
12.666
12.684

12.653

OD 3
(0.4987)
(0.4994)

(0.4981)




0.0030
0.0340

0.0600

(0.0001)
(0.0013)

(0.0024)
B
12.687
12.700


12.713
ID 1
(0.4995)
(0.5000)


(0.5005)
Subtask 27-84-62-220-081-A
AE. Dimensional Check of Slat 3, Track 8
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.639

OD 20
(0.4987)
(0.4994)

(0.4976)




0.0220
0.0580

0.1120

(0.0009)
(0.0023)

(0.0044)
C
12.706
12.724


12.751
ID 18
(0.5002)
(0.5009)


(0.5020)
Subtask 27-84-62-220-082-A
AF. Dimensional Check of Slat 3, Track 8
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.653

OD 20
(0.4987)
(0.4994)

(0.4981)




0.0030
0.0340

0.0600

(0.0001)
(0.0013)

(0.0024)
C
12.687
12.700


12.713
ID 19
(0.4995)
(0.5000)


(0.5005)
Subtask 27-84-62-220-083-A
AG. Dimensional Check of Slat 3, Track 8
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.639

OD 4
(0.4987)
(0.4994)

(0.4976)




0.0220
0.0580

0.1120

(0.0009)
(0.0023)

(0.0044)
C
12.706
12.724


12.751
ID 13
(0.5002)
(0.5009)


(0.5020)
Subtask 27-84-62-220-084-A
AH. Dimensional Check of Slat 3, Track 8
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
15.836
15.854

15.820

OD 7
(0.6235)
(0.6242)

(0.6228)




0.0080
0.0390

0.0710

(0.0003)
(0.0015)

(0.0028)
C
15.862
15.875


15.891
ID 12
(0.6245)
(0.6250)


(0.6256)
Subtask 27-84-62-220-085-A
AI. Dimensional Check of Slat 3, Track 8
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
18.959
18.980

18.927

OD 6
(0.7464)
(0.7472)

(0.7452)




0.0270
0.0690

0.1330

(0.0011)
(0.0027)

(0.0052)
C
19.007
19.028


19.060
ID 21
(0.7483)
(0.7491)


(0.7504)
Subtask 27-84-62-220-086-A
AJ. Dimensional Check of Slat 3, Track 8
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.643

OD 4
(0.4987)
(0.4994)

(0.4978)




0.0160
0.0520

0.0980

(0.0006)
(0.0020)

(0.0039)
C
12.700
12.718


12.741
ID 8
(0.5000)
(0.5007)


(0.5016)
Subtask 27-84-62-220-087-A
AK. Dimensional Check of Slat 4, Track 9
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
B
12.666
12.684

12.639

OD 1
(0.4987)
(0.4994)

(0.4976)




0.0220
0.0580

0.1120

(0.0009)
(0.0023)

(0.0044)
B
12.706
12.724


12.751
ID 2
(0.5002)
(0.5009)


(0.5020)
Subtask 27-84-62-220-088-A
AL. Dimensional Check of Slat 4, Track 9
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
B
12.666
12.684

12.653

OD 1
(0.4987)
(0.4994)

(0.4981)




0.0030
0.0340

0.0600

(0.0001)
(0.0013)

(0.0024)
B
12.687
12.700


12.713
ID 3
(0.4995)
(0.5000)


(0.5005)
Subtask 27-84-62-220-089-A
AM. Dimensional Check of Slat 4, Track 9
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
15.966
15.984

15.943

OD 21
(0.6286)
(0.6293)

(0.6277)




0.0160
0.0520

0.0980

(0.0006)
(0.0020)

(0.0039)
C
16.000
16.018


16.041
ID 20
(0.6299)
(0.6306)


(0.6315)
Subtask 27-84-62-220-090-A
AN. Dimensional Check of Slat 4, Track 9
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.640

OD 17
(0.4987)
(0.4994)

(0.4976)




0.0160
0.0610

0.1130

(0.0006)
(0.0024)

(0.0044)
C
12.700
12.727


12.753
ID 21
(0.5000)
(0.5011)


(0.5021)
Subtask 27-84-62-220-091-A
AO. Dimensional Check of Slat 4, Track 9
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.653

OD 17
(0.4987)
(0.4994)

(0.4981)




0.0030
0.0340

0.0600

(0.0001)
(0.0013)

(0.0024)
C
12.687
12.700


12.713
ID 19
(0.4995)
(0.5000)


(0.5005)
Subtask 27-84-62-220-092-A
AP. Dimensional Check of Slat 4, Track 9
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.643

OD 17
(0.4987)
(0.4994)

(0.4978)




0.0160
0.0520

0.0980

(0.0006)
(0.0020)

(0.0039)
C
12.700
12.718


12.741
ID 18
(0.5000)
(0.5007)


(0.5016)
Subtask 27-84-62-220-093-A
AQ. Dimensional Check of Slat 4, Track 9
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.639

OD 13
(0.4987)
(0.4994)

(0.4976)




0.0220
0.0580

0.1120

(0.0009)
(0.0023)

(0.0044)
C
12.706
12.724


12.751
ID 6
(0.5002)
(0.5009)


(0.5020)
Subtask 27-84-62-220-094-A
AR. Dimensional Check of Slat 4, Track 9
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
15.836
15.854

15.820

OD 10
(0.6235)
(0.6242)

(0.6228)




0.0080
0.0390

0.0710

(0.0003)
(0.0015)

(0.0028)
C
15.862
15.875


15.891
ID 7
(0.6245)
(0.6250)


(0.6256)
Subtask 27-84-62-220-095-A
AS. Dimensional Check of Slat 4, Track 9
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
18.959
18.980

18.927

OD 11
(0.7464)
(0.7472)

(0.7452)




0.0270
0.0690

0.1330

(0.0011)
(0.0027)

(0.0052)
C
19.007
19.028


19.060
ID 8
(0.7483)
(0.7491)


(0.7504)
Subtask 27-84-62-220-096-A
AT. Dimensional Check of Slat 4, Track 9
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.643

OD 13
(0.4987)
(0.4994)

(0.4978)




0.0160
0.0520

0.0980

(0.0006)
(0.0020)

(0.0039)
C
12.700
12.718


12.741
ID 9
(0.5000)
(0.5007)


(0.5016)
Subtask 27-84-62-220-097-A
AU. Dimensional Check of Slat 4, Track 10
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
B
12.666
12.684

12.639

OD 3
(0.4987)
(0.4994)

(0.4976)




0.0220
0.0580

0.1120

(0.0009)
(0.0023)

(0.0044)
B
12.706
12.724


12.751
ID 1
(0.5002)
(0.5009)


(0.5020)
Subtask 27-84-62-220-098-A
AV. Dimensional Check of Slat 4, Track 10
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
B
12.666
12.684

12.653

OD 3
(0.4987)
(0.4994)

(0.4981)




0.0030
0.0340

0.0600

(0.0001)
(0.0013)

(0.0024)
B
12.687
12.700


12.713
ID 2
(0.4995)
(0.5000)


(0.5005)
Subtask 27-84-62-220-099-A
AW. Dimensional Check of Slat 4, Track 10
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.639

OD 20
(0.4987)
(0.4994)

(0.4976)




0.0220
0.0580

0.1120

(0.0009)
(0.0023)

(0.0044)
C
12.706
12.724


12.751
ID 18
(0.5002)
(0.5009)


(0.5020)
Subtask 27-84-62-220-100-A
AX. Dimensional Check of Slat 4, Track 10
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.653

OD 20
(0.4987)
(0.4994)

(0.4981)




0.0030
0.0340

0.0600

(0.0001)
(0.0013)

(0.0024)
C
12.687
12.700


12.713
ID 19
(0.4995)
(0.5000)


(0.5005)
Subtask 27-84-62-220-101-A
AY. Dimensional Check of Slat 4, Track 10
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.639

OD 4
(0.4987)
(0.4994)

(0.4976)




0.0220
0.0580

0.1120

(0.0009)
(0.0023)

(0.0044)
C
12.706
12.724


12.751
ID 13
(0.5002)
(0.5009)


(0.5020)
Subtask 27-84-62-220-102-A
AZ. Dimensional Check of Slat 4, Track 10
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
15.836
15.854

15.820

OD 7
(0.6235)
(0.6242)

(0.6228)




0.0080
0.0390

0.0710

(0.0003)
(0.0015)

(0.0028)
C
15.862
15.875


15.891
ID 12
(0.6245)
(0.6250)


(0.6256)
Subtask 27-84-62-220-103-A
BA. Dimensional Check of Slat 4, Track 10
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
18.959
18.980

18.927

OD 6
(0.7464)
(0.7472)

(0.7452)




0.0270
0.0690

0.1330

(0.0011)
(0.0027)

(0.0052)
C
19.007
19.028


19.060
ID 21
(0.7483)
(0.7491)


(0.7504)
Subtask 27-84-62-220-104-A
BB. Dimensional Check of Slat 4, Track 10
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.643

OD 4
(0.4987)
(0.4994)

(0.4978)




0.0160
0.0520

0.0980

(0.0006)
(0.0020)

(0.0039)
C
12.700
12.718


12.741
ID 8
(0.5000)
(0.5007)


(0.5016)
Subtask 27-84-62-220-105-A
BC. Dimensional Check of Slat 5, Track 11
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
B
9.497
9.512

9.472

OD 1
(0.3739)
(0.3745)

(0.3729)




0.0230
0.0530

0.1080

(0.0009)
(0.0021)

(0.0043)
B
9.535
9.550


9.580
ID 2
(0.3754)
(0.3760)


(0.3772)
Subtask 27-84-62-220-106-A
BD. Dimensional Check of Slat 5, Track 11
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
B
9.497
9.512

9.488

OD 1
(0.3739)
(0.3745)

(0.3735)




0.0000
0.0280

0.0460

(0.0000)
(0.0011)

(0.0018)
B
9.512
9.525


9.534
ID 3
(0.3745)
(0.3750)


(0.3754)
Subtask 27-84-62-220-107-A
BE. Dimensional Check of Slat 5, Track 11
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
B
9.497
9.512

9.472

OD 12
(0.3739)
(0.3745)

(0.3729)




0.0230
0.0530

0.1030

(0.0009)
(0.0021)

(0.0041)
B
9.535
9.550


9.575
ID 4
(0.3754)
(0.3760)


(0.3770)
Subtask 27-84-62-220-108-A
BF. Dimensional Check of Slat 5, Track 11
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
B
12.666
12.684

12.653

OD 14
(0.4987)
(0.4994)

(0.4981)




0.0030
0.0340

0.0600

(0.0001)
(0.0013)

(0.0024)
B
12.687
12.700


12.713
ID 7
(0.4995)
(0.5000)


(0.5005)
Subtask 27-84-62-220-109-A
BG. Dimensional Check of Slat 5, Track 11
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
B
15.966
15.984

15.939

OD 13
(0.6286)
(0.6293)

(0.6275)




0.0220
0.0580

0.1120

(0.0009)
(0.0023)

(0.0044)
B
16.006
16.024


16.051
ID 16
(0.6302)
(0.6309)


(0.6319)
Subtask 27-84-62-220-110-A
BH. Dimensional Check of Slat 5, Track 11
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
B
9.497
9.512

9.478

OD 12
(0.3739)
(0.3745)

(0.3731)




0.0130
0.0430

0.0810

(0.0005)
(0.0017)

(0.0032)
B
9.525
9.540


9.559
ID 15
(0.3750)
(0.3756)


(0.3763)
Subtask 27-84-62-220-111-A
BI. Dimensional Check of Slat 5, Track 11
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.466
12.484

12.443

OD 17
(0.4908)
(0.4915)

(0.4899)




0.0160
0.0520

0.0980

(0.0006)
(0.0020)

(0.0039)
C
12.500
12.518


12.541
ID 18
(0.4921)
(0.4928)


(0.4937)
Subtask 27-84-62-220-112-A
BJ. Dimensional Check of Slat 5, Track 11
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
9.497
9.512

9.473

OD 20
(0.3739)
(0.3745)

(0.3730)




0.0180
0.0550

0.1030

(0.0007)
(0.0022)

(0.0041)
C
9.530
9.552


9.576
ID 17
(0.3752)
(0.3761)


(0.3770)
Subtask 27-84-62-220-113-A
BK. Dimensional Check of Slat 5, Track 11
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
9.497
9.512

9.489

OD 20
(0.3739)
(0.3745)

(0.3736)




0.0000
0.0280

0.0440

(0.0000)
(0.0011)

(0.0017)
C
9.512
9.525


9.533
ID 21
(0.3745)
(0.3750)


(0.3753)
Subtask 27-84-62-220-114-A
BL. Dimensional Check of Slat 5, Track 11
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
9.497
9.512

9.478

OD 20
(0.3739)
(0.3745)

(0.3731)




0.0130
0.0430

0.0810

(0.0005)
(0.0017)

(0.0032)
C
9.525
9.540


9.559
ID 19
(0.3750)
(0.3756)


(0.3763)
Subtask 27-84-62-220-115-A
BM. Dimensional Check of Slat 5, Track 12
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
B
11.079
11.097

11.062

OD 6
(0.4362)
(0.4369)

(0.4355)




-0.0010
0.0350

0.0690

(0.0000)
(0.0014)

(0.0027)
B
11.096
11.114


11.131
ID 2
(0.4369)
(0.4376)


(0.4382)
Subtask 27-84-62-220-116-A
BN. Dimensional Check of Slat 5, Track 12
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
B
11.079
11.097

11.067

OD 6
(0.4362)
(0.4369)

(0.4357)




0.0030
0.0340

0.0580

(0.0001)
(0.0013)

(0.0023)
B
11.100
11.113


11.125
ID 1
(0.4370)
(0.4375)


(0.4380)
Subtask 27-84-62-220-117-A
BO. Dimensional Check of Slat 5, Track 12
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
B
9.497
9.512

9.472

OD 5
(0.3739)
(0.3745)

(0.3729)




0.0230
0.0530

0.1030

(0.0009)
(0.0021)

(0.0041)
B
9.535
9.550


9.575
ID 3
(0.3754)
(0.3760)


(0.3770)
Subtask 27-84-62-220-118-A
BP. Dimensional Check of Slat 5, Track 12
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
B
9.497
9.512

9.488

OD 5
(0.3739)
(0.3745)

(0.3735)




0.0000
0.0280

0.0460

(0.0000)
(0.0011)

(0.0018)
B
9.512
9.525


9.534
ID 4
(0.3745)
(0.3750)


(0.3754)
Subtask 27-84-62-220-119-A
BQ. Dimensional Check of Slat 5, Track 12
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
9.497
9.512

9.472

OD 30
(0.3739)
(0.3745)

(0.3729)




0.0230
0.0530

0.1030

(0.0009)
(0.0021)

(0.0041)
C
9.535
9.550


9.575
ID 9
(0.3754)
(0.3760)


(0.3770)
Subtask 27-84-62-220-120-A
BR. Dimensional Check of Slat 5, Track 12
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
9.497
9.512

9.488

OD 30
(0.3739)
(0.3745)

(0.3735)




0.0000
0.0280

0.0460

(0.0000)
(0.0011)

(0.0018)
C
9.512
9.525


9.534
ID 7
(0.3745)
(0.3750)


(0.3754)
Subtask 27-84-62-220-121-A
BS. Dimensional Check of Slat 5, Track 12
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
11.079
11.097

11.062

OD 29
(0.4362)
(0.4369)

(0.4355)




-0.0010
0.0350

0.0690

(0.0000)
(0.0014)

(0.0027)
C
11.096
11.114


11.131
ID 12
(0.4369)
(0.4376)


(0.4382)
Subtask 27-84-62-220-122-A
BT. Dimensional Check of Slat 5, Track 12
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
11.079
11.097

11.064

OD 29
(0.4362)
(0.4369)

(0.4356)




0.0030
0.0410

0.0710

(0.0001)
(0.0016)

(0.0028)
C
11.100
11.120


11.135
ID 15
(0.4370)
(0.4378)


(0.4384)
Subtask 27-84-62-220-123-A
BU. Dimensional Check of Slat 5, Track 12
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
9.497
9.512

9.472

OD 25
(0.3739)
(0.3745)

(0.3729)




0.0230
0.0530

0.1030

(0.0009)
(0.0021)

(0.0041)
C
9.535
9.550


9.575
ID 18
(0.3754)
(0.3760)


(0.3770)
Subtask 27-84-62-220-124-A
BV. Dimensional Check of Slat 5, Track 12
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
12.666
12.684

12.653

OD 22
(0.4987)
(0.4994)

(0.4981)




0.0030
0.0340

0.0600

(0.0001)
(0.0013)

(0.0024)
C
12.687
12.700


12.713
ID 19
(0.4995)
(0.5000)


(0.5005)
Subtask 27-84-62-220-125-A
BW. Dimensional Check of Slat 5, Track 12
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
15.966
15.984

15.939

OD 23
(0.6286)
(0.6293)

(0.6275)




0.0220
0.0580

0.1120

(0.0009)
(0.0023)

(0.0044)
C
16.006
16.024


16.051
ID 20
(0.6302)
(0.6309)


(0.6319)
Subtask 27-84-62-220-126-A
BX. Dimensional Check of Slat 5, Track 12
   (1) Fits and clearance dimensions
NOTE: The limits on the chrome-plated surfaces only apply when there is a layer of chrome on the bearing surfaces.

FIG. DETAIL AND ITEM N°
ORIGINAL MANUFACTURING LIMITS
IN-SERVICE WEAR LIMITS
C
9.497
9.512

9.478

OD 25
(0.3739)
(0.3745)

(0.3731)




0.0130
0.0430

0.0810

(0.0005)
(0.0017)

(0.0032)
C
9.525
9.540


9.559
ID 21
(0.3750)
(0.3756)


(0.3763)
5. Close-up
Subtask 27-84-62-410-053-A
A. Close Access
   (1) Make sure that the parts retained from the removed component are clean and in the correct condition.
   (2) For the Slat track 5,
F Slat 2, Track 5 - Attachment Details ** ON A/C NOT FOR ALL
F Slat 2, Track 5 - Attachment Details ** ON A/C NOT FOR ALL
apply a layer of Synthetic Oil base Grease-General Purpose Lithium Thickened - (Material No.03GBD1) to:
  • the bolts (15) and (18)
  • the eccentric bush (14)
  • the bearing (9).
   (3) For the Slat track 5
     (a) Put the bolt (18) in the link (10) and install the links (8) and (10).
     (b) Install the eccentric bush (14), the bolt (15), the washer (6) and the nut (7). Tighten the nut (7) with your hand (this will be safetied when the Slat No. 2 is installed).
NOTE: The bolts (1) and (19) and their related nuts and washers will be correctly installed when the Slat No. 2 is installed.
   (4) For the Slat track 6,
F Slat 2, Track 6 - Attachment Details
apply a layer of Synthetic Oil base Grease-General Purpose Lithium Thickened - (Material No.03GBD1) to:
  • the bolts (4), (18) and (20)
  • the eccentric bush (5)
  • the bearings (10) and (17).
   (5) For the Slat track 6
     (a) Put the bolt (20) in the link (9) and install the links (9) and (11).
     (b) Install the eccentric bush (5), the bolt (4), the washer (12) and the nut (13). Tighten the nut (13) with your hand (this will be safetied when the Slat No. 2 is installed).
     (c) Install the two links (16), the bolts (18), the washers (14) and the nuts (15). Tighten the nuts (15) with your hand (these will be safetied when the Slat No. 2 is installed).
NOTE: The bolts (3) and their related nuts and washers will be correctly installed when the Slat No. 2 is installed.
   (6) For the Slat track 7,
F Slat 3, Track 7 - Attachment Details
apply a layer of Synthetic Oil base Grease-General Purpose Lithium Thickened - (Material No.03GBD1) to:
  • the bolts (12) and (15)
  • the eccentric bush (6)
  • the bearing (13).
   (7) For the Slat track 7
     (a) Put the bolt (12) in the link (21) and install the links (14) and (21).
     (b) Install the eccentric bush (6), the bolt (15), the washer (5) and the nut (4). Tighten the nut (4) with your hand (this will be safetied when the Slat No. 3 is installed).
NOTE: The bolts (3) and (16) and their related nuts and washers will be correctly installed when the Slat No. 3 is installed.
   (8) For the Slat track 8,
F Slat 3, Track 8 - Attachment Details
apply a layer of Synthetic Oil base Grease-General Purpose Lithium Thickened - (Material No.03GBD1) to:
  • the bolts (4), (11) and (20)
  • the eccentric bush (5)
  • the bearings (12) and (19).
   (9) For the Slat track 8
     (a) Put the bolt (11) in the link (21) and install the links (13) and (21).
     (b) Install the eccentric bush (5), the bolt (4), the washer (14) and the nut (15). Tighten the nut (15) with your hand (this will be safetied when the Slat No. 3 is installed).
     (c) Install the two links (18), the bolts (20), the washers (16) and the nuts (17). Tighten the nuts (17) with your hand (these will be safetied when the Slat No. 3 is installed).
NOTE: The bolts (3) and their related nuts and washers will be correctly installed when the Slat No. 3 is installed.
   (10) For the Slat track 9,
F Slat 4, Track 9 - Attachment Details
apply a layer of Synthetic Oil base Grease-General Purpose Lithium Thickened - (Material No.03GBD1) to:
  • the bolts (13) and (16)
  • the eccentric bush (12)
  • the bearing (7).
   (11) For the Slat track 9
     (a) Put the bolt (16) in the link (8) and install the links (6) and (8).
     (b) Install the eccentric bush (12), the bolt (13), the washer (5) and the nut (4). Tighten the nut (4) with your hand (this will be safetied when the Slat No. 4 is installed).
NOTE: The bolts (1) and (17) and their related nuts and washers will be correctly installed when the Slat No. 4 is installed.
   (12) For the Slat track 10,
F Slat 4, Track 10 - Attachment Details
apply a layer of Synthetic Oil base Grease-General Purpose Lithium Thickened - (Material No.03GBD1) to:
  • the bolts (4), (11) and (20)
  • the eccentric bush (5)
  • the bearings (12) and (19).
   (13) For the Slat track 10
     (a) Put the bolt (11) in the link (21) and install the links (13) and (21).
     (b) Install the eccentric bush (5), the bolt (4), the washer (14) and the nut (15). Tighten the nut (15) with your hand (this will be safetied when the Slat No. 4 is installed).
     (c) Install the two links (18), the bolts (20), the washers (16) and the nuts (17). Tighten the nuts (17) with your hand (these will be safetied when the Slat No. 4 is installed).
NOTE: The bolts (3) and their related nuts and washers will be correctly installed when the Slat No. 4 is installed.
   (14) For the Slat track 11,
F Slat 5, Track 11 - Attachment Details ** ON A/C NOT FOR ALL
F Slat 5, Track 11 - Attachment Details ** ON A/C NOT FOR ALL
apply a layer of Synthetic Oil base Grease-General Purpose Lithium Thickened - (Material No.03GBD1) to:
  • the bolts (8) and (12)
  • the eccentric bush (11)
  • the bearing (7).
   (15) For the Slat track 11
     (a) Put the bolt (8) in the link (16) and install the links (4) and (16).
     (b) Install the eccentric bush (11), the bolt (12), the washer (6) and the nut (5). Tighten the nut (5) with your hand (this will be safetied when the Slat No. 5 is installed).
NOTE: The bolts (1) and (20) and their related nuts and washers will be correctly installed when the Slat No. 5 is installed.
   (16) For the Slat track 12,
F Slat 5, Track 12 - Attachment Details
apply a layer of Synthetic Oil base Grease-General Purpose Lithium Thickened - (Material No.03GBD1) to:
  • the bolts (25), (28), (29) and (30)
  • the eccentric bush (24)
  • the bearings (7), (15) and (19).
   (17) For the Slat track 12
     (a) Put the bolt (28) in the link (20) and install the links (18) and (20).
     (b) Install the eccentric bush (24), the bolt (25), the washer (17) and the nut (16). Tighten the nut (16) with your hand (this will be safetied when the Slat No. 5 is installed).
     (c) Install the links (8) and (31), the bolt (29), the washer (13) and the nut (14).
     (d) Install the bolt (30), the washer (10) and the nut (11). Tighten the nuts (14) and (11) with your hand (these will be safetied when the Slat No. 5 is installed).
NOTE: The bolts (5) and (6) and their related nuts and washers will be correctly installed when the Slat No. 5 is installed.
   (18) Install the applicable Slat track (Ref. AMM TASK 27-84-62-400-001).
   (19) Install the applicable Slat:
Subtask 27-84-62-942-053-A
B. Removal of Equipment
   (1) Remove the safety barriers.
   (2) Make sure that the work area is clean and clear of tools and other items.
   (3) Remove the WARNING NOTICE(S).
   (4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
[Rev.10 from 2021] 2026.03.31 23:58:03 UTC
"Aviabrain" 2025