Removal of the Side Rollers - Slat Tracks 5 thru 12

TASK 27-84-62-000-002-A
Removal of the Side Rollers - Slat Tracks 5 thru 12

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:

THE FLIGHT CONTROLS
THE FLIGHT CONTROL SURFACES
THE LANDING GEAR AND THE RELATED DOORS
COMPONENTS THAT MOVE.

MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.

WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.

1. Reason for the Job
Self Explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment

REFERENCE	QTY	DESIGNATION
No specific	AR	ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE
No specific	AR	SAFETY BARRIER(S)
No specific	AR	SAFETY CLIP - CIRCUIT BREAKER
No specific	AR	WARNING NOTICE(S)

B. Referenced Information

REFERENCE	DESIGNATION
TASK 27-84-49-000-001-A	Removal of the Type B Actuators
TASK 27-84-49-000-002-A	Removal of the Type B Actuators
TASK 27-84-61-000-001-A	Removal of the Slat Tracks 1 thru 4
TASK 27-84-64-000-001-A	Removal of the No. 2 Slat
TASK 27-84-65-000-001-A	Removal of the No 3 Slat
TASK 27-84-66-000-001-A	Removal of the No. 4 Slat
TASK 27-84-67-000-001-A	Removal of the No. 5 Slat
Side Rollers and Vertical Rollers - Detail and Location ** ON A/C NOT FOR ALL
Side Rollers and Vertical Rollers - Detail and Location ** ON A/C NOT FOR ALL

3. Job Set-up
Subtask 27-84-62-941-054-A

A. Safety Precautions
(1) Put the SAFETY BARRIER(S) in position.
(2) Put a WARNING NOTICE(S) in the cockpit to tell persons not to operate the slat controls.
(3) Make sure that the 98D27803500001 LOCKING TOOL ZERO POS or 98D27803500002 LOCKING TOOL ZERO POS is on the slat/flap control lever.

Subtask 27-84-62-865-052-A

B. Open, safety and tag this(these) circuit breaker(s):

PANEL	DESIGNATION	FIN	LOCATION
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1	5CV	B06
** ON A/C NOT FOR ALL
49VU	FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1	5CV	B01
** ON A/C ALL
121VU	FLIGHT CONTROLS/SLT/CTL/SYS2	7CV	R21

Subtask 27-84-62-010-051-A

C. Get Access
(1) Put an ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE below the applicable zone 510 or 610.
(2) Remove the applicable slat:

for track 5 and 6 side-rollers (Ref. AMM TASK 27-84-64-000-001)
for track 7 and 8 side-rollers (Ref. AMM TASK 27-84-65-000-001)
for track 9 and 10 side-rollers (Ref. AMM TASK 27-84-66-000-001)
for track 11 and 12 side-rollers (Ref. AMM TASK 27-84-67-000-001).

(3) Remove the applicable actuators:

for tracks 5, 6, 8, 10 and 12 (Ref. AMM TASK 27-84-49-000-001)
for tracks 7, 9 and 11 (Ref. AMM TASK 27-84-49-000-002).

(4) When it is necessary to remove all the side-rollers (20), remove the applicable track (2) (Ref. AMM TASK 27-84-61-000-001).

NOTE: To replace two or more side-rollers from opposite sides of the track, you must remove all the side-rollers. Keep the serviceable side-rollers and their related shims together for the installation.
To replace side-rollers at the same side of the track, remove only the side-rollers you are to replace.

(5) Make sure that the 98D27803500001 LOCKING TOOL ZERO POS or 98D27803500002 LOCKING TOOL ZERO POS is on the slat/flap control lever.

4. Procedure
Subtask 27-84-62-020-051-A

A. Removal of the Side Rollers - Slat Tracks 5 thru 12

WARNING: USE PROTECTIVE GOGGLES AND GLOVES WHEN YOU REMOVE OR INSTALL LOCKWIRE. EACH TIME YOU CUT LOCKWIRE, REMOVE AND DISCARD IT IMMEDIATELY. LOOSE LOCKWIRE CAN CUT YOU OR MAKE YOU BLIND, AND/OR CAN CAUSE DAMAGE.

(1) For tracks 8 and 11, where applicable, remove and discard the lockwire from the bolts (21).
(2) Remove the bolts (21), the washers (22), the applicable side-roller(s) (20) and the shims (23).

[Rev.10 from 2021] 2026.03.31 23:58:02 UTC