W DOC AIRBUS | AMM A320F

Removal of the Torque Shaft

TASK 27-54-45-000-010-A
Removal of the Torque Shaft

WARNING: PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU START A TASK ON OR NEAR:
  • THE FLIGHT CONTROLS
  • THE FLIGHT CONTROL SURFACES
  • THE LANDING GEAR AND THE RELATED DOORS
  • COMPONENTS THAT MOVE.
MOVEMENT OF COMPONENTS CAN KILL OR CAUSE INJURY TO PERSONS AND/OR CAN CAUSE DAMAGE TO THE EQUIPMENT.
WARNING: MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING GEAR. THIS WILL PREVENT UNWANTED MOVEMENT OF THE LANDING GEAR, AND THUS POSSIBLE INJURY TO PERSONS AND DAMAGE TO THE AIRCRAFT AND/OR EQUIPMENT.
CAUTION: BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
  • DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
  • DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
  • MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
FIN: 6222CM
FIN: 6272CM
1. Reason for the Job
Self explanatory
2. Job Set-up Information
 A. Fixtures, Tools, Test and Support Equipment
REFERENCE
QTY
DESIGNATION
No specific
AR
ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE
No specific
AR
SAFETY BARRIER(S)
No specific
AR
SAFETY CLIP - CIRCUIT BREAKER
No specific
AR
WARNING NOTICE(S)
98D27504030001
1
LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT
98D27604000000
1
COLLAR-SAFETY, SPOILER
98D27604004000
1
COLLAR SAFETY SPOILER
98D27803000000
1
LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION
 B. Work Zones and Access Panels
ZONE/ACCESS
ZONE DESCRIPTION
FOR [6222CM] (FLAP XMSN TORQUE SHAFT)
575CB
FOR [6272CM] (FLAP XMSN TORQUE SHAFT)
675CB
 C. Referenced Information
REFERENCE
DESIGNATION
TASK 27-50-00-400-003-A
Installation of the Lock-Torque Shaft - Flaps and Slats (98D27504030001)
TASK 27-50-00-866-008-A
Extension of the Flaps on the Ground
TASK 27-50-00-866-008-A-01
Extension of the Flaps/Slats on the Ground
TASK 27-60-00-866-002-A
Extension-Retraction of the Spoilers for Maintenance
TASK 57-51-37-000-004-A
Removal of the Access Panels 575AB(675AB), 575BB(675BB), 575CB(675CB), 575DB(675DB), 575EB(675EB), 575FB(675FB), 575GB(675GB), 575HB(675HB)
F Torque Shafts - Flap Power Transmission ** ON A/C NOT FOR ALL
F Torque Shafts- Flap Power Transmission
F Torque Shafts - Flap Power Transmission ** ON A/C NOT FOR ALL
3. Job Set-up
Subtask 27-54-45-941-057-A
A. Safety Precautions
   (1) As necessary, use the applicable SAFETY BARRIERS, specified by the operator's instructions and your local regulations.
   (2) Put a WARNING NOTICE(S) in position to tell persons not to operate the flap/slat controls.
Subtask 27-54-45-860-059-A
B. Aircraft Maintenance Configuration
WARNING: MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS SURFACES ARE CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE TO EQUIPMENT.
   (1) Extend the flaps fully (Ref. AMM TASK 27-50-00-866-008).
   (2) Install the 98D27803000000 LOCKING TOOL-FLAP SLAT LEVER,INT. POSITION on the flap/slat control lever.
Subtask 27-54-45-865-057-A
C. Open, safety and tag this(these) circuit breaker(s):
PANELDESIGNATIONFINLOCATION
** ON A/C NOT FOR ALL
49VUFLIGHT CONTROLS/FLP/CTL AND MONG/SYS16CVB07
** ON A/C NOT FOR ALL
49VUFLIGHT CONTROLS/FLP/CTL AND MONG/SYS16CVB02
** ON A/C ALL
121VUFLIGHT CONTROLS/FLP/CTL AND/MONG/SYS28CVQ21
Subtask 27-54-45-010-058-A
D. Get Access
   (1) Put the ACCESS PLATFORM 4M (13 FT)-ADJUSTABLE in the applicable position.
   (2) Remove the applicable access panel (Ref. AMM TASK 57-51-37-000-004):
     (a) FOR [6222CM] (FLAP XMSN TORQUE SHAFT)
remove 575CB
     (b) FOR [6272CM] (FLAP XMSN TORQUE SHAFT)
remove 675CB.
   (3) Put the applicable spoiler in the 'M' (Maintenance) position (Ref. AMM TASK 27-60-00-866-002).
   (4) Put the 98D27604000000 COLLAR-SAFETY, SPOILER or 98D27604004000 COLLAR SAFETY SPOILER on the piston rod of the servo-control.
4. Procedure
CAUTION: BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
  • DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
  • DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
  • MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
Subtask 27-54-45-020-059-A
A. Removal of the Torque Shaft
   (1) Install the 98D27504030001 LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT on a torque shaft, outboard of the component that you remove (Ref. AMM TASK 27-50-00-400-003).
   (2) Remove and discard the nuts (80).
   (3) Remove the bolts (81) and the torque shaft (78).
   (4) Remove the torque shaft (79).
[Rev.10 from 2021] 2026.04.01 07:00:05 UTC
"Aviabrain" 2025