DOC AIRBUS | AMM A320FRemoval of the Fire Extinguisher Bottle
TASK 26-25-41-000-001-A
Removal of the Fire Extinguisher Bottle
Self explanatory
2. Job Set-up Information
A. Work Zones and Access Panels
B. Referenced Information
3. Job Set-up
Subtask 26-25-41-861-050-A ** ON A/C NOT FOR ALL
Subtask 26-25-41-020-050-B ** ON A/C NOT FOR ALL
(1) Remove the waste bin.
(2) Remove the fire extinguisher bottle (4):
(a) If the nut-clips (5) are installed:
1 Remove the screws (3).
2 Carefully remove the fire extinguisher bottle (4) and the washers (2) from the waste-bin housing.
3 If necessary, remove the nut-clips (5) from the fire extinguisher bottle (4).
(b) If the nuts (1) are installed:
1 Remove the nuts (1) and the screws (3).
2 Carefully remove the fire extinguisher bottle (4) and the washers (2) from the waste-bin housing.
Subtask 26-25-41-020-050-C ** ON A/C NOT FOR ALL
(1) Remove the fire extinguisher bottle (3):
(a) Remove the screws (2).
(b) Carefully remove the fire extinguisher bottle (3) and the washers (1) from the waste-bin housing.
(c) If necessary, remove the nut-clips (4) from the fire extinguisher bottle (3).
[Rev.10 from 2021]
2026.04.01 04:24:06 UTC
Removal of the Fire Extinguisher Bottle
ZONE: 200
FIN: 7910MM ** ON A/C NOT FOR ALL
FIN: 7911MM ** ON A/C NOT FOR ALL
FIN: 7912MM ** ON A/C NOT FOR ALL
FIN: 7914MM31 ** ON A/C NOT FOR ALL
FIN: 7914MM41 ** ON A/C NOT FOR ALL
FIN: 7914MM42 ** ON A/C NOT FOR ALL
1. Reason for the JobFIN: 7910MM ** ON A/C NOT FOR ALL
FIN: 7911MM ** ON A/C NOT FOR ALL
FIN: 7912MM ** ON A/C NOT FOR ALL
FIN: 7914MM31 ** ON A/C NOT FOR ALL
FIN: 7914MM41 ** ON A/C NOT FOR ALL
FIN: 7914MM42 ** ON A/C NOT FOR ALL
Self explanatory
2. Job Set-up Information
A. Work Zones and Access Panels
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 200 | UPPER HALF FUSELAGE |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 24-42-00-861-001-A | Energize the Ground Service Network from the External Power |
| TASK 25-40-00-00 | LAVATORIES - DESCRIPTION AND OPERATION |
| TASK 26-25-00-00 | LAVATORY FIRE EXTINGUISHING - DESCRIPTION AND OPERATION |
Fire Extinguisher BottleSubtask 26-25-41-861-050-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) Energize the ground service network
(Ref. AMM TASK 24-42-00-861-001).
Subtask 26-25-41-010-050-A ** ON A/C NOT FOR ALL (1) Energize the ground service network
(Ref. AMM TASK 24-42-00-861-001).
B. Get Access
(1) For the location of this component refer to (Ref. AMM D/O 25-40-00-00), (Ref. AMM D/O 26-25-00-00).
(2) Get access to the related lavatory and open the service door.
4. Procedure(1) For the location of this component refer to (Ref. AMM D/O 25-40-00-00), (Ref. AMM D/O 26-25-00-00).
(2) Get access to the related lavatory and open the service door.
Subtask 26-25-41-020-050-B ** ON A/C NOT FOR ALL
CAUTION:
MAKE SURE THAT YOU DO NOT BEND THE DISCHARGE TUBE(S) WHEN YOU REMOVE OR INSTALL THE FIRE EXTINGUISHER. IF YOU DO, YOU CAN CAUSE DAMAGE TO THE JOINT BETWEEN THE DISCHARGE TUBE AND THE CONTAINER.
A. Removal of the Fire Extinguisher Bottle (1) Remove the waste bin.
(2) Remove the fire extinguisher bottle (4):
(a) If the nut-clips (5) are installed:
1 Remove the screws (3).
2 Carefully remove the fire extinguisher bottle (4) and the washers (2) from the waste-bin housing.
3 If necessary, remove the nut-clips (5) from the fire extinguisher bottle (4).
(b) If the nuts (1) are installed:
1 Remove the nuts (1) and the screws (3).
2 Carefully remove the fire extinguisher bottle (4) and the washers (2) from the waste-bin housing.
CAUTION:
MAKE SURE THAT YOU DO NOT BEND THE DISCHARGE TUBE(S) WHEN YOU REMOVE OR INSTALL THE FIRE EXTINGUISHER. IF YOU DO, YOU CAN CAUSE DAMAGE TO THE JOINT BETWEEN THE DISCHARGE TUBE AND THE CONTAINER.
A. Removal of the Fire Extinguisher Bottle (1) Remove the fire extinguisher bottle (3):
(a) Remove the screws (2).
(b) Carefully remove the fire extinguisher bottle (3) and the washers (1) from the waste-bin housing.
(c) If necessary, remove the nut-clips (4) from the fire extinguisher bottle (3).