Visual Check of the Pressure Indication of the Inflation Reservoir - Escape-Slides at Doors 2/3

TASK 25-62-00-040-002-A
Visual Check of the Pressure Indication of the Inflation Reservoir - Escape-Slides at Doors 2/3

1. Reason for the Job

NOTE: This deactivation task is not related to an AFM-CDL/MMEL item.

2. Job Set-up Information
A. Referenced Information

REFERENCE	DESIGNATION
TASK 25-62-49-000-001-A	Removal of the Escape-Slide Inflation Reservoir
TASK 25-62-49-400-001-A	Installation of the Escape-Slide Inflation Reservoir
Inflation Reservoir Pressure-Gage ** ON A/C NOT FOR ALL
Pressure Gage - Inflation Reservoir ** ON A/C NOT FOR ALL

3. Job Set-up
Subtask 25-62-00-010-065-A ** ON A/C NOT FOR ALL

A. Get Access
(1) Remove/open the access panel to the escape-slide inflation reservoir (Ref. AMM TASK 25-62-49-000-001).

4. Procedure
Subtask 25-62-00-210-064-A ** ON A/C NOT FOR ALL

A. Visual Inspection

Inflation Reservoir Pressure-Gage ** ON A/C NOT FOR ALL

(1) Make sure that the pressure gage (1) (referred to as gage) shows the correct pressure.

NOTE: There are two different types of gage (1) (MODEL A and MODEL B). MODEL A has a green cursor which is temperature sensitive. MODEL B has a needle with an internal mechanism, which is temperature sensitive. They can give temporary low pressure indications when there are sudden temperature changes (from a cold to a warm environment). The cursor/needle moves to changes in temperature faster than the gas can expand in the inflation reservoir.

(a) The permitted indications for MODEL A are as follows:

The needle in AREA A (green cursor width) shows that the pressure indication is correct.
The needle in AREA B, which is half the range of AREA A, shows a permitted indication, because of sudden temperature changes.

(b) The permitted indications for MODEL B are as follows:

The GREEN BAND shows a correct indication
AREA B, which has a range equal to AREA A, shows a permitted indication because of sudden temperature changes.

(c) If the gage (1) shows an incorrect indication:
1 Let the temperature conditions become stable, then examine the gage (1) again.
2 If the gage needle continues to show an incorrect indication, replace the inflation reservoir (Ref. AMM TASK 25-62-49-000-001).

Subtask 25-62-00-210-064-B ** ON A/C NOT FOR ALL

A. Visual Inspection

Pressure Gage - Inflation Reservoir ** ON A/C NOT FOR ALL

(1) Make sure that the pressure gage (1) (referred to as gage) shows the correct pressure.

NOTE: The gage (1) has a needle with an internal mechanism, which is temperature sensitive. They can give temporary low pressure indications when there are sudden temperature changes (from a cold to a warm environment). The needle moves to changes in temperature faster than the gas can expand in the inflation reservoir.

(a) The permitted indications are as follows:

The GREEN BAND shows a correct indication
AREA B, which has a range equal to AREA A, shows a permitted indication because of sudden temperature changes.

(b) If the gage (1) shows an incorrect indication:
1 Let the temperature conditions become stable, then examine the gage (1) again.
2 If the gage needle continues to show an incorrect indication, replace the inflation reservoir (Ref. AMM TASK 25-62-49-000-001).

5. Close-up
Subtask 25-62-00-410-060-A ** ON A/C NOT FOR ALL

A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Install/Close the inflation reservoir access-panel (Ref. AMM TASK 25-62-49-400-001).
(3) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

[Rev.10 from 2021] 2026.03.31 23:40:00 UTC