DOC AIRBUS | AMM A320FInstallation of the Net Stanchions in the Forward Cargo Compartment
TASK 25-54-17-400-001-A
Installation of the Net Stanchions in the Forward Cargo Compartment
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Work Zones and Access Panels
C. Referenced Information
3. Job Set-up
Subtask 25-54-17-860-050-A ** ON A/C NOT FOR ALL
Subtask 25-54-17-910-050-A ** ON A/C NOT FOR ALL
Subtask 25-54-17-865-055-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.03.31 23:39:06 UTC
Installation of the Net Stanchions in the Forward Cargo Compartment
ZONE: 130
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | ACCESS PLATFORM 2M (6 FT) |
| No specific | 1 | WARNING NOTICE(S) |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 130 | FWD CARGO COMPT AFT BULKHEAD OF AVNCS COMPT TO FWD PRESSURE BULKHEAD OF WING CENTER BOX |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 52-30-00-080-001-A | Removal of the Safety Support Equipment |
| TASK 52-30-00-480-001-A | Installation of the Safety Support Equipment |
| TASK 52-30-00-860-001-A | Open the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump |
| TASK 52-30-00-860-002-A | Close the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump |
Stanchion - Door Net - Forward Cargo CompartmentSubtask 25-54-17-860-050-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) Make sure that the forward cargo-compartment door is open (Ref. AMM TASK 52-30-00-860-001).
(2) Make sure that the ACCESS PLATFORM 2M (6 FT) is in position at the opening of the forward cargo-compartment door.
Subtask 25-54-17-860-050-B ** ON A/C NOT FOR ALL (1) Make sure that the forward cargo-compartment door is open (Ref. AMM TASK 52-30-00-860-001).
(2) Make sure that the ACCESS PLATFORM 2M (6 FT) is in position at the opening of the forward cargo-compartment door.
A. Aircraft Maintenance Configuration
(1) Make sure that the forward cargo-compartment door is open (Ref. AMM TASK 52-30-00-860-001).
(2) Make sure that the forward cargo-compartment door is safetied with the actuator safety lock (Ref. AMM TASK 52-30-00-480-001).
(3) Make sure that the ACCESS PLATFORM 2M (6 FT) is in position at the opening of the forward cargo-compartment door.
(4) Make sure that the WARNING NOTICE(S) is in position on the control panel of the forward cargo-loading-system to tell persons not to use it.
Subtask 25-54-17-865-054-A ** ON A/C NOT FOR ALL (1) Make sure that the forward cargo-compartment door is open (Ref. AMM TASK 52-30-00-860-001).
(2) Make sure that the forward cargo-compartment door is safetied with the actuator safety lock (Ref. AMM TASK 52-30-00-480-001).
(3) Make sure that the ACCESS PLATFORM 2M (6 FT) is in position at the opening of the forward cargo-compartment door.
(4) Make sure that the WARNING NOTICE(S) is in position on the control panel of the forward cargo-loading-system to tell persons not to use it.
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:
4. Procedure| PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 2000VU | SEMI AUTO CLS-FWD | 3MY | E08 |
| 2000VU | SEMI AUTO CLS-FWD | 2MY | E06 |
Subtask 25-54-17-910-050-A ** ON A/C NOT FOR ALL
A. Preparation for Installation:
(1) Do an inspection of the component interfaces and the adjacent area.
(2) Clean the component interfaces and the adjacent area.
(3) Make sure that the parts retained from the removed component are clean and in the correct condition.
Subtask 25-54-17-420-050-A ** ON A/C NOT FOR ALL (1) Do an inspection of the component interfaces and the adjacent area.
(2) Clean the component interfaces and the adjacent area.
(3) Make sure that the parts retained from the removed component are clean and in the correct condition.
B. Installation of the Net Stanchions.
(1) Make sure that the stanchion locking base (3) is in the unlocked position.
(2) Carefully insert the stanchion plunger (2) in the upper ceiling fitting (1).
(3) Push the stanchion (2) up and align the stanchion locking base (3) with the tie-down point (4).
(4) Carefully lower the stanchion (2).
(5) Make sure that the stanchion locking base (3) is in the correct position on the tie-down point (4).
(6) Turn the stanchion locking base (3) clockwise 90 degrees to attach the stanchion (2) to the tie-down point (4).
(7) Make sure that the stanchion (2) is correctly attached.
(8) Connect the net fittings to the applicable net attachment fittings, if necessary.
5. Close-up(1) Make sure that the stanchion locking base (3) is in the unlocked position.
(2) Carefully insert the stanchion plunger (2) in the upper ceiling fitting (1).
(3) Push the stanchion (2) up and align the stanchion locking base (3) with the tie-down point (4).
(4) Carefully lower the stanchion (2).
(5) Make sure that the stanchion locking base (3) is in the correct position on the tie-down point (4).
(6) Turn the stanchion locking base (3) clockwise 90 degrees to attach the stanchion (2) to the tie-down point (4).
(7) Make sure that the stanchion (2) is correctly attached.
(8) Connect the net fittings to the applicable net attachment fittings, if necessary.
Subtask 25-54-17-865-055-A ** ON A/C NOT FOR ALL
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
Subtask 25-54-17-410-050-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 2000VU | SEMI AUTO CLS-FWD | 3MY | E08 |
| 2000VU | SEMI AUTO CLS-FWD | 2MY | E06 |
B. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the forward cargo-compartment door (Ref. AMM TASK 52-30-00-860-002).
(3) Remove the access platform(s).
Subtask 25-54-17-410-050-B ** ON A/C NOT FOR ALL (1) Make sure that the work area is clean and clear of tools and other items.
(2) Close the forward cargo-compartment door (Ref. AMM TASK 52-30-00-860-002).
(3) Remove the access platform(s).
B. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the safety lock from the actuator of the forward cargo-compartment door (Ref. AMM TASK 52-30-00-080-001).
(3) Remove the WARNING NOTICE(S).
(4) Close the forward cargo-compartment door (Ref. AMM TASK 52-30-00-860-002).
(5) Remove the access platform(s).
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the safety lock from the actuator of the forward cargo-compartment door (Ref. AMM TASK 52-30-00-080-001).
(3) Remove the WARNING NOTICE(S).
(4) Close the forward cargo-compartment door (Ref. AMM TASK 52-30-00-860-002).
(5) Remove the access platform(s).