DOC AIRBUS | AMM A320FInstallation of the Control Panel
TASK 25-52-67-400-001-A
Installation of the Control Panel
Self explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
B. Consumable Materials
C. Work Zones and Access Panels
D. Referenced Information
3. Job Set-up
Subtask 25-52-67-860-050-A ** ON A/C NOT FOR ALL
Subtask 25-52-67-910-050-A ** ON A/C NOT FOR ALL
Subtask 25-52-67-410-050-A ** ON A/C NOT FOR ALL
[Rev.10 from 2021]
2026.04.01 06:27:31 UTC
Installation of the Control Panel
WARNING:
DO NOT GET THE FLUID ON YOUR SKIN OR IN YOUR EYES. IF YOU DO:
- FLUSH IT AWAY WITH CLEAN WATER
- GET MEDICAL AID.
WARNING:
BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURER'S INSTRUCTIONS AND YOUR LOCAL REGULATIONS.
CAUTION:
USE ONLY THE SPECIFIED MATERIALS AND OBEY THE INSTRUCTIONS FROM THE MATERIAL MANUFACTURERS. OTHER MATERIALS CAN CAUSE DAMAGE TO THE SURFACE PROTECTION OF THE COMPONENTS AND THE RELATED AREA.
1. Reason for the JobSelf explanatory
2. Job Set-up Information
A. Fixtures, Tools, Test and Support Equipment
| REFERENCE | QTY | DESIGNATION |
|---|---|---|
| No specific | 1 | ACCESS PLATFORM 2M (6 FT) |
| No specific | 1 | WARNING NOTICE(S) |
| REFERENCE | DESIGNATION |
|---|---|
| (Material No.06LCG9) | Non Hardening Jointing Putty-Medium Temp. Area - - |
| ZONE/ACCESS | ZONE DESCRIPTION |
|---|---|
| 130 | FWD CARGO COMPT AFT BULKHEAD OF AVNCS COMPT TO FWD PRESSURE BULKHEAD OF WING CENTER BOX |
| 150 | AFT CARGO COMPARTMENT FWD PRESS BULKHEAD TO AFT BULKHEAD OF AFT CARGO COMPARTMENT |
| REFERENCE | DESIGNATION |
|---|---|
| TASK 25-52-00-710-004-A | Operational Test of the Door Sill Latches in the Forward Cargo Compartment and in the Aft Cargo Compartment |
| TASK 25-52-00-710-005-A | Operational Test of the Power Drive Units |
| TASK 52-30-00-860-001-A | Open the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump |
| TASK 52-30-00-860-002-A | Close the FWD or Aft Cargo-Compartment Door with the Yellow Electric Pump |
Control Panel 2020VUSubtask 25-52-67-860-050-A ** ON A/C NOT FOR ALL
A. Aircraft Maintenance Configuration
(1) Make sure that the forward and/or aft cargo-compartment door is/are opened (Ref. AMM TASK 52-30-00-860-001).
(2) Make sure that the ACCESS PLATFORM 2M (6 FT) is in position at the opening of the applicable cargo-compartment door.
(3) Make sure that the WARNING NOTICE(S) is in position at the applicable control panel of the cargo loading system.
Subtask 25-52-67-865-058-A ** ON A/C NOT FOR ALL (1) Make sure that the forward and/or aft cargo-compartment door is/are opened (Ref. AMM TASK 52-30-00-860-001).
(2) Make sure that the ACCESS PLATFORM 2M (6 FT) is in position at the opening of the applicable cargo-compartment door.
(3) Make sure that the WARNING NOTICE(S) is in position at the applicable control panel of the cargo loading system.
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged:
4. Procedure| PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 2000VU | SEMI AUTO CLS-FWD | 3MY | E08 |
| 2000VU | SEMI AUTO CLS-FWD | 2MY | E06 |
| 2001VU | SEMI AUTO CLS-AFT | 103MY | D08 |
| 2001VU | SEMI AUTO CLS-AFT | 102MY | D06 |
Subtask 25-52-67-910-050-A ** ON A/C NOT FOR ALL
A. Preparation for the Installation
(1) Clean the component interfaces and the adjacent area.
(2) Do an inspection of the component interfaces and the adjacent area.
(3) Make sure that the work area is clean and clear of tools and other items.
(4) Apply Non Hardening Jointing Putty-Medium Temp. Area - - (Material No.06LCG9) to the thread of the screws (3).
Subtask 25-52-67-420-050-A ** ON A/C NOT FOR ALL (1) Clean the component interfaces and the adjacent area.
(2) Do an inspection of the component interfaces and the adjacent area.
(3) Make sure that the work area is clean and clear of tools and other items.
(4) Apply Non Hardening Jointing Putty-Medium Temp. Area - - (Material No.06LCG9) to the thread of the screws (3).
B. Installation of the Control Panel 2020VU in the Forward and/or Aft Cargo Compartment
(1) Remove the CAP-BLANKING from each electrical connector and receptacle.
(2) Make sure that all the electrical connections are clean and in the correct condition.
(3) Connect the electrical connector (1) to the receptacle (4).
(4) Put the control panel (2) in its correct installation position on the structure (5).
(5) Install the screws (3).
(6) Install the insulation near the control panel (2).
Subtask 25-52-67-865-059-A ** ON A/C NOT FOR ALL (1) Remove the CAP-BLANKING from each electrical connector and receptacle.
(2) Make sure that all the electrical connections are clean and in the correct condition.
(3) Connect the electrical connector (1) to the receptacle (4).
(4) Put the control panel (2) in its correct installation position on the structure (5).
(5) Install the screws (3).
(6) Install the insulation near the control panel (2).
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
Subtask 25-52-67-710-051-A ** ON A/C NOT FOR ALL | PANEL | DESIGNATION | FIN | LOCATION |
|---|---|---|---|
| ** ON A/C NOT FOR ALL | |||
| 2000VU | SEMI AUTO CLS-FWD | 3MY | E08 |
| 2000VU | SEMI AUTO CLS-FWD | 2MY | E06 |
| 2001VU | SEMI AUTO CLS-AFT | 103MY | D08 |
| 2001VU | SEMI AUTO CLS-AFT | 102MY | D06 |
D. Test
(1) Do this test (Ref. AMM TASK 25-52-00-710-004).
(2) Do this test (Ref. AMM TASK 25-52-00-710-005).
5. Close-up(1) Do this test (Ref. AMM TASK 25-52-00-710-004).
(2) Do this test (Ref. AMM TASK 25-52-00-710-005).
Subtask 25-52-67-410-050-A ** ON A/C NOT FOR ALL
A. Close Access
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the WARNING NOTICE(S).
(3) Remove the access platform(s).
(4) Close the forward and/or aft cargo-compartment door (Ref. AMM TASK 52-30-00-860-002).
(1) Make sure that the work area is clean and clear of tools and other items.
(2) Remove the WARNING NOTICE(S).
(3) Remove the access platform(s).
(4) Close the forward and/or aft cargo-compartment door (Ref. AMM TASK 52-30-00-860-002).